Related Manuals for AlienTek UT70
Summary of Contents for AlienTek UT70
- Page 1 UT70 USB Tester User Manual User High Performance USB Tester Manual User Manual Revision history Version Date Modify V1.00 2023/09/18 First release...
-
Page 2: Table Of Contents
2.4.3 Tool interface ....................11 2.4.4 Setting interface .................... 14 3，ATK-UT70 Instructions ..................17 3.1 UT70 USB test driver installed ................17 3.2 Install the running environment of the upper computer software ..... 18 3.3 ATK-UT70 Function description ................19 3.2 ATK-UT70 Firmware upgrade ..................20 3.3 Firmware update precautions .................. -
Page 3: Notes
9, When the load current of some fast charging adapters / power bank is low (< 50mA), the external power supply may be stopped. At this time, the power bank mode of UT70 can be used to provide fake load and maintain power supply. - Page 4 UT70 USB Tester User Manual High Performance USB Tester Detailed specification parameters of UT70 USB tester are shown in Table 1.1: Items Description Product model: UT70 Screen size: 0.96 inch IPS screen Basic parameters LCD resolution: 160 * 80 Product size: 67.5mm * 24.5mm * 10.5mm Net weight: 15g USB-A IN（Public seat）：7A...
-
Page 5: 2，Quick Start
(1) Used in conjunction with PC to download good UT70 USB tester data package, there is a configuration software, for a link below: http://www.openedv.com/docs/t ool/USB/index.html... -
Page 6: Appearance Description
2.4 Function Description 2.4.1 Main interface The UT70 USB tester has four main interfaces, and when the main interface can switch states, these four main interfaces can be switched by sliding the left/right buttons. User Manual... - Page 7 UT70 USB Tester User Manual High Performance USB Tester 1. Basic measurement interface The basic measurement interface is used to display the most basic measurement parameters, including voltage, current, power, operation time, electric quantity and other information. Figure 2.2 Basic measurement interface Interface introduction: ①...
- Page 8 UT70 USB Tester User Manual High Performance USB Tester Operating instructions: Short press: Key to switch to the previous main interface. ◀ Short press the key to switch the upload frequency. ■ Short press: Key to switch to the next main interface.
- Page 9 UT70 USB Tester User Manual High Performance USB Tester 3. Data recording interface The data recording interface is used to record the Ah/Wh flowing from the power supply to the device offline. It supports a maximum of 4 groups of data records (10200 points/group, the default is recorded once every 1 second, the interval can be set).
-
Page 10: Fast Charging Protocol Testing Interface
UT70 USB Tester User Manual High Performance USB Tester Application Function Interface The application function interface is used to select different functions, achieve protocol detection, tool detection, settings, etc., as shown in the following figure. Figure 2.5 Function Application Interface... - Page 11 UT70 USB Tester User Manual High Performance USB Tester Figure 2.7 Automatic detection completion interface Interface Introduction: ① The name of the detected fast charging protocol. ② The detection results of the corresponding protocol may vary depending on the protocol description.
- Page 12 UT70 USB Tester User Manual High Performance USB Tester interface, click the Select Application Function [Pro] icon to enter the automatic detection and trigger selection interface. The first time you enter, you will be prompted to unplug all external devices. After clicking [OK], select the [PD] option to start PD protocol triggering, as shown in the following figure.
-
Page 13: Tool Interface
UT70 USB Tester User Manual High Performance USB Tester After successful triggering, voltage selection： Short press: Key, cycle up to switch the desired voltage/step voltage reduction. ◀ Short press: Key, cycle down to switch the desired voltage/step voltage increase. ▶... - Page 14 UT70 USB Tester User Manual High Performance USB Tester Long press: key to forcibly exit the identification cable. ■ After successful cable identification: Short press : key to restart cable identification. ■ When testing E-marker cables, it is important to note that it is recommended not to use the Type-C port for power supply (it is recommended to use Micro USB power supply or USB A port power supply instead), otherwise it may cause abnormal testing.
- Page 15 Figure 2.13 Start of line resistance measurement The measurements were performed as follows: 1. Connect the UT70 to the power supply device using the cable to be tested (do not connect the UT70 to any load, and the current is displayed as 0).
-
Page 16: Setting Interface
UT70 USB Tester User Manual High Performance USB Tester 2.4.4 Setting interface Operate the [Application Functions] main interface in sequence —>[Set] icon option to enter the settings interface, as shown in the following figure. Figure 2.15 Setting interface Data Record Setting Interface In the [Settings] interface above, select the [Data Record] option and briefly press to enter the data record settings interface. - Page 17 UT70 USB Tester User Manual High Performance USB Tester Function items Interpretation Operation mode Adjustable range Start this mode, conduct false loads at intervals, simulate device power consumption, and prevent power loss Power Bank due to low current of the power bank...
- Page 18 UT70 USB Tester User Manual High Performance USB Tester brightness backlight after how long it takes ->Left and right key minutes adjustment Middle key short press Set the default brightness for backlight brightness ->Left and right key 3%-100% display adjustment Table 2.3.4.5 Backlight Setting Options...
-
Page 19: 3，Atk-Ut70 Instructions
3.1 UT70 USB test driver installed When the UT70 USB tester is connected to the computer through the Micro USB cable for the first time, the computer will automatically install the driver for it. Please wait until the driver is installed before it can be used with the upper computer. -
Page 20: Install The Running Environment Of The Upper Computer Software
If the user's computer does not have it installed. NET4.0 running environment, you can use the downloaded data pack inside. To install the running environment, go to the UT70 USB Tester Data Pack/Configuration software/Software Running environment dotNetFx40_Full_x86_x64.exe. If it has already been installed, click the environment installation package to install it, and the following message will be displayed indicating that the computer has been installed and there is no need to reinstall it. -
Page 21: Atk-Ut70 Function Description
3.3 ATK-UT70 Function description Figure 3.2.1 ATK-UT70 main interface Interface introduction: Device information: display the model and version of UT70 (USB tester). Equipment / Host computer function control 1, Reconnect / Disconnect: controls and displays the current connection status. 2, Language: set software language. -
Page 22: Atk-Ut70 Firmware Upgrade
At this time, the maximum recording time for the file is only half an hour 3.2 ATK-UT70 Firmware upgrade The firmware update of ATK-UT70 software supports two upgrade modes: local mode and net mode. -
Page 23: Firmware Update Precautions
UT70 USB Tester User Manual High Performance USB Tester Then operate the host computer in the following steps: ① Click on the "Update" option on the upper computer, and an upgrade window will pop up. Select "Net mode", ② Then Click on the "Start Upgrade" option in the upper computer upgrade window, and the tester itself will jump to the upgrade mode to display the upgrade interface. -
Page 24: 4，Faq
4，FAQ 4.1 Solve different problems first If the user UT70 has a problem, he can give priority to updating the upper computer and updating the firmware of the tester to see if the problem disappears. If these problems persist, you can ask us after sales for help and support. -
Page 25: The Fast Charge Protocol Detects And Triggers Exceptions
UT70 USB Tester User Manual High Performance USB Tester and then access the line and equipment。 If you access two C lines to monitor, you can't blind plug, C1 to C1 surface, not C1C2, because there is only one line in the C line for communication, C_IN is C1 communication, C_OUT side should also be connected to C1 communication. -
Page 26: Hid Port On The Button Side
0, and D+/D- will be similarly close to 0. 5，Services 1. After – sales Service： UT70 has a one-year free warranty service in the case of non-artificial damage. Please contact the dealer for warranty service. 2. Website Download www.alientek.com/download...
Need help?
Do you have a question about the UT70 and is the answer not in the manual?
Questions and answers