Related Manuals for HNC HT3000-D Series
Summary of Contents for HNC HT3000-D Series
- Page 1 HT3000-D Series Intelligent HMI User Manual High-definition and high-speed intelligent HMI...
-
Page 2: Table Of Contents
Content 1. Product introduction ................................4 1. Main functions ................................4 2. Core Highlights ................................4 2. Product specifications ................................ 4 3. HMI supporting software ..............................6 3. Product size ..................................7 1. HT300-D4 ..................................7 2. HT3000-D7 ..................................8 3. HT3000-D10 ................................9 4. - Page 3 b. Download project ................................16 c. Run project ..................................16 3.HTCloud manager ................................17 a. Enter device manager interface ............................17 Local manager ................................17 Could manager ................................17 b. Excute device management ..............................17 Download project ..............................17 U upload project ............................... 18 ...
-
Page 4: Product Introduction
Product description 一、 1. The main function The HT3000 embedded system is developed based on the embedded Linux system . It is an embedded system software that runs on industrial automation monitoring and management equipment. By running the configuration project, you can intuitively observe the industrial site conditions and communicate with various industrial control equipment. - Page 5 Memory (RAM) 512M Ethernet port 10/100Base-T *1 10/100 Base-T *1 10/100/ 10 00 Base-T *1 10/100Base-T *1 COM1: RS232*1 COM1: RS232*1 serial interface COM2: RS485*1 COM2: RS485*1 COM3: RS485*1 USB HOST USB2.0 *1 USB2.0 * 2 Built-in real-time clock Input power 24V DC ±20% Power consumption 6 W @24VDC...
-
Page 6: Hmi Supporting Software
Global 4G 三、 HMI supporting software 1. HT3000 needs to be used with HTCloud Designer editing software. Please download from HNC official website: www.hncelectric.com 2. It is also recommended to download Cloud APP “IoTBus” 3. Cloud APP “IoTBus” download: ... -
Page 7: Product Size
Product Size 三、 1. D4 7 / 38... -
Page 8: Ht3000-D7
2. D7 8 / 38... -
Page 9: Ht3000-D10
3. D10 9 / 38... -
Page 10: Ht3000-D15
4. D15 4 HMI interface diagram 1. D4 2. D4E 10 / 38... -
Page 11: Ht3000-D4W
3. D4W 4. D7/D10 COM1 /2 pin definition definition definition Carrier Detect (DBD) Data ready (DSR) Accept data (RXD) N.B. Send data (TXD) N.B. N.B. N.B. Signal ground (SG) 5. D7E/D10E COM1 /2 pin definition definition definition Carrier Detect (DBD) Data ready (DSR) Accept data (RXD) N.B. -
Page 12: D7W/D10W
6. D7W/D10W COM1 /2 pin definition definition definition Carrier Detect (DBD) Data ready (DSR) Accept data (RXD) N.B. Send data (TXD) N.B. N.B. N.B. Signal ground (SG) 7. D15 COM 1 pin definition definition definition Carrier Detect (DBD) Data ready (DSR) Accept data (RXD) N.B. -
Page 13: Ht3000-D15W/D15Ew
Accept data (RXD) N.B. Send data (TXD) N.B. N.B. N.B. Signal ground (SG) 9. D15W/D15EW COM 1 pin definition definition definition Carrier Detect (DBD) Data ready (DSR) Accept data (RXD) N.B. Send data (TXD) N.B. N.B. N.B. Signal ground (SG) 5 HMI installation and use 1. -
Page 14: Screen Calibration
3. Screen calibration It has a " power-on calibration " function . Press and hold the HMI screen, then connect the power to the HMI. After hearing the buzzer beeps three times at intervals, the device will enter the calibration interface. A calibration mark will appear on the upper left side of the screen . -
Page 15: Software Instructions
Software Instructions 1. HMI connection settings HT3000 communicates with the PLC through the RS232 serial port, RS485 serial port or Ethernet port. During the hardware wiring process, the HT3000-10 communicates with the PLC through the RS232 serial port and connects to the static Ethernet network. a. -
Page 16: Download Project
b. Download project Project Step 1: Enter the device manager, you can choose to use the local manager or cloud manager; Step 2: Click [Download project] to enter the project download confirmation interface; Step 3: In the confirmation download interface, you can choose whether to reserve the history and alarm records, whether to reserve the formula and whether to package the font download. -
Page 17: Htcloud Manager
3. HTCloud manager Open the HTCloud Designer software in computer, click the device manager icon of menu; or click the [project}, open the [ HTCloud Designer ] installation document ,open the [ HTCloud Manager ] and enter device manager. Support to use the local manager and cloud manager effective control HMI. -
Page 18: U Upload Project
Firmware update Step 1: click [ Firmware update ],choice firm package, click [open] , The latest firmware update package can be get from HNC Step 2: enter offline update confirm interface, click [update] Step 3: waiting for update to complete, pop-up prompt " update success " , click [OK]. -
Page 19: Start Calibration
Start calibration Click [ start calibration ], the device enter the calibration interface, press the calibration mark 1above the screen for long time, and enter next calibration site, calibration the device touch the screen in order of " left , right, up, down, mid " ... - Page 20 ① split history file Step 1: click [start split file], you can split historical files for the recent period of time. Step 2: waiting to split the historical record to complete, pop-up prompt [split success], click [OK], historical file list will add current split historical files.
-
Page 21: Restart The Device
③ Delete history file Step 1: Select the history file in the history file list and click [Delete Select File] Step 2: Pop up the Confirm Delete File prompt box and click [Yes]; Step 3: Wait for the history file to be deleted successfully. The " Delete Successful! " prompt box will pop up, click [OK]. ... -
Page 22: Background Settings
4. Background settings Long press the upper right corner of the HMI device to enter the background setting s interface, or access the HMI through a browser, enter IP / setting to enter the background setting s interface a. Project Settings ... - Page 23 Step 2: Enter the compilation interface, set the appropriate output path after compilation, click [Save]; Step 3: After the running file is saved successfully, the system will pop up a prompt box of saving successfully, click [OK]. D ownload project ...
-
Page 24: Network Settings
b. Network Settings Ethernet connection Enter the HT3000-10 background setting s interface, click [Network], enter the Ethernet setting s interface, open the [Switch], the network type includes DHCP and Static IP. ① Dynamic IP Connect the network cable, select [DHCP] for the network type, and click [Save], the device will automatically obtain the IP. ②... - Page 25 after verification. After the connection is successful, display the green tick " ". After the connection is successful, you can see the gray i "", click the gray i icon can set the IP address, subnet mask, default gateway, DNS. After setting, click [Save] to set WI-FI IP address information.
-
Page 26: Personal Hot Spot
Click the gray i icon and then click [Close] to close the window. Personal hot spot Click [AP] to enter the personal hot spot interface, the HMI built-in network card can also be shared to share WI-FI hot spots for other users. -
Page 27: Network Configuration Model
Set password, click "Password", a password input box pops up, click on the upper left corner of the input box to switch the plaintext ciphertext of the password. Enter the password, click [Enter], and click [Save] to save the added password information. The factory default WI-FI password is empty. -
Page 28: Routing Configuration
With 4G (HT3000-7G) The HMI with WI-FI version includes Ethernet, 4G ,and routing modules, without WI-FI / hot spots, and the network is provided by the network cable / 4G. The routing modes include: :close routing /4G client mode. The specific use of each routing mode will be explained below. ... - Page 29 Comparison of various routing modes and network types: Close routing 4G routing 4G client AP MODE Repeated mode _ Client mode ( Routing switch ) mode mode Ethernet LAN/Internet LAN/Internet unsupported unsupported Connect to the Wi-Fi LAN/Internet unsupported unsupported Connect to the Internet unsupported Internet Hotpot...
- Page 30 4G routing mode Enter the HMI background settings interface, click [Network], enter the routing configuration interface, click "Settings", click "4G Routing Mode", a prompt "Will this turn off WI-FI,confirm switching to this mode?", click "ok" to set the 4G routing mode. In "4G routing"...
-
Page 31: Settings
mode, The client mode will fix the IP to 192.168.255.1. In the "Client" mode, the network is provided by the hot spot connected by WI-FI. At this time, the HMI is equivalent to a router. The HMI is connected to the wired network, and then connected to the device through the wire to provide the network to the device. In this mode, personal hot spot function is not supported. -
Page 32: Security Settings
② Set terminal code Enter the HMI background settings interface, click [Settings], in the [Settings] interface, you can see [Terminal code], click [Set], enter the new terminal code, and click Enter on the keyboard. ③ Set buzzer switch Enter the HMI background settings interface, click [Settings], in the [Settings] interface, you can see [Beep], turn on [Beep], when the user clicks the button, the buzzer will respond sound. - Page 33 the firmware, otherwise it cannot be executed related operations. ② Enter background password Adding password verification into the background can avoid potential security risks and economic losses caused by misoperation of unrelated personnel. The specific operations are as follows: Step 1: Enter the HMI background settings interface, click [Settings]; Step 2: Open the [Enter the set interface password] function on the [Security] interface;...
-
Page 34: Others
④ Enable screen calibration Click [Screen calibration], pop up [Enabling calibration will restart the device, whether to restart the calibration?], click OK to perform touch screen calibration. Others ① Set the frequency of cloud online detection Enter the HMI background settings interface, click [Settings], switch to the [Others] interface, click Settings on [Cloud On-line Detection], select the cloud online detection frequency which we need. -
Page 35: System Information
③ MQTT Agency The firmware version 3.16.0.20/2.16.0.20 and later versions add the MQTT agency function. Click on the "MQTT Agency" to turn on or off the MQTT agency. Turning on the MQTT agent means to use the HMI as a small MQTT server with the server address either Ethernet or WI-FI IP address from the device, please refer to the MQTT user manual. -
Page 36: Cloud Settings
Enter the HMI background settings, click [Information], select [Update], enter the firmware upgrade interface, select [USB], then select the appropriate firmware update package, and click [OK] to upgrade the firmware. After the upgrade is successful , the device will restart. SD card update firmware Enter the HMI background settings, click [Information], select [Update], enter the firmware update interface, select [SD], select the appropriate firmware update package, and click [OK] to update the firmware. -
Page 37: Multi-Language Settings
Remote control Enter the APP on mobile phone and enter the device; click [Access] to access the device. If the current project allows remote operation, the user can remotely control the device through the mobile phone. Multi-language settings Enter the HMI background settings interface, click the language settings button at the top right of the screen, you can switch the system language, the device supports two languages: simplified Chinese and English. -
Page 38: Exit Background Settings
Exit background settings On the HMI background settings interface, click [Back] to exit the background settings and enter the project running interface. 38 / 38...
Need help?
Do you have a question about the HT3000-D Series and is the answer not in the manual?
Questions and answers