JANUS INTERNATIONAL NOKE ION Install Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

SCAN FOR PDF

NOKĒ ION

INSTALL

GUIDE

Table of Contents

Need help?

Do you have a question about the NOKE ION and is the answer not in the manual?

Questions and answers

Summary of Contents for JANUS INTERNATIONAL NOKE ION

Page 1 SCAN FOR PDF NOKĒ ION INSTALL GUIDE...
Page 2: Install Guide
Nokē Ion Install Guide Nokē Ion Install Guide (Internal Use Only) Revised 10/22/24...
Page 3: Table Of Contents
Nokē Ion Install Guide (Internal Use Only) Table of Contents Introduc?on ..............................1 Dimensions ............................... 2 Installing the Notched Sliding Latch ......................3 Adding the Lock to the NSE System ......................5 Installing the Nokē Ion Lock ......................... 7 Installing the Wirepas Antenna ........................ 7 Installing the Nokē...
Page 4: Introduc?On
Nokē Ion Install Guide (Internal Use Only) Introduc2on The Nokē Smart Entry (NSE) system has two main hardware parts when installed on a standard roll up door: a wired Nokē Ion Lock Body, which is mounted inside the storage unit on a door rail, and a Notched Sliding Latch, which is mounted on the outside of the unit’s door. These two pieces are aligned so that the Lock Body will catch and secure the Notched Sliding Latch when locked. The Nokē Ion system offers optional peripheral attachments, including an optional wall-mount RGB LED status indicator light, and an in-unit Motion Detector. The Nokē Ion Lock Body requires a standard 12Vdc power source when connected to the PIR Motion Sensor; otherwise, if there is no motion sensor connected then the Noke ̄ Ion will accept power inputs from 12Vdc to 24Vdc. Nokē Ion locks automatically form a secure wireless mesh network to ensure reliable communication. Nokē gateways strategically located throughout the facility connect this wireless mesh network to Nokē ’ s encrypted cloud servers. The Nokē Ion locks pass activity logs from one lock to the next until a Noke ̄ gateway is within signal range, and then the information is sent back through the cloud.
Page 5: Dimensions
Nokē Ion Install Guide (Internal Use Only) Dimensions 1.02in. x 1.71in. x 9.56in. (26.0mm. x 43.5mm. x 242.9mm) Material: Chrome Plated Zinc and ABS Plas?c Connec.vity: Bluetooth enabled, Wirepas Power: 12V - 24V DC with 20mA standby current Lock Ac.va.on: 200mA Opera.ng Temperature: 14°F to 122°F (-10°C to 50°C) Water Resistance Ra.ng: Alerts: Audible sounds with op?onal mul?-color LED...
Page 6: Installing The Notched Sliding Latch
Nokē Ion Install Guide (Internal Use Only) Installing the Notched Sliding Latch If you are doing a retroYit installation, make sure to remove the standard Janus sliding latch from the door before installing the notched sliding latch and Noke ̄ Ion lock body. (Available in left or right- handed versions.) Le5-hand (Part #200460-0001) and Right-hand (Part #200460-0000) Right-hand version is displayed. To install the notched sliding latch, 1. Switch out the standard sliding latch with either the right or le`-handed notched sliding latch. Cau.on: Ensure that the notch on the sliding latch is facing down towards the ﬂoor so that the locking apparatus within the Nokē...
Page 7 Nokē Ion Install Guide (Internal Use Only) 3. Par?ally open the door enough to enter the unit, and then pull the door back down to view the back of the sliding latch assembly. 4. Secure the latch with the four lock nuts. Tighten the nuts with an impact driver. 5.
Page 8: Adding The Lock To The Nse System
Nokē Ion Install Guide (Internal Use Only) Adding the Lock to the NSE System Add the lock to the NSE system via the Nokē Storage Smart Entry manager’s mobile app. To add a lock, 1. Open your Nokē Storage Smart Entry manager’s mobile app, and then tap + (top-right corner). 2. Tap Add Unit Controller.
Page 9 Nokē Ion Install Guide (Internal Use Only) 9. Enter the Unit name in the Search ﬁeld to locate the unit, and then tap Unlock. 10. Slide the latch to close the unit. 11. Conﬁrm the lock is closed. Step 9 Step 10 Step 11 12.
Page 10: Installing The Nokē Ion Lock
Nokē Ion Install Guide (Internal Use Only) Installing the Nokē Ion Lock Installing the Wirepas Antenna Op#on 1: Interior storage units or Exterior storage units with LoS between unit interiors The Wirepas antenna is an accessory that must be mounted at the top of the door frame. Antennas perform best when they have Line of Sight (LoS) to each other to form a strong mesh network. Before starting the installation, ensure that the length of the antenna cabling is sufYicient to reach the Nokē Ion lock body inside the unit. Additionally, allow for some extra space to neatly bundle any excess power supply and antenna cables at the top of the door header, securing them with the provided zip ties. This approach will create a tidy and professional appearance, reducing the risk of tenants inadvertently snagging cables while moving items in and out of their units. To install the antenna, 1.
Page 11 Nokē Ion Install Guide (Internal Use Only) 4. Ahach the Screw-On Antenna to the SMA Connector. Tighten with 5 in-lb of torque. !Do NOT Over5ghten! 5. The cable will be run to the Nokē Ion Lock Body in the following sec?on. Con?nue to the next sec?on to ﬁnish the moun?ng process.
Page 12 Nokē Ion Install Guide (Internal Use Only) 3. Mount the External Antenna cover to the wall using 3 screws (Sheet Metal or Concrete Anchors). Make sure the Drain sec?on of the design is facing down and the Foam Gasket is on the top. 4.
Page 13: Installing The Nokē Ion Lock Body
Nokē Ion Install Guide (Internal Use Only) Installing the Nokē Ion Lock Body The Nokē Ion lock body bolts to the inside of the unit on the door rail. It’s important to align the sliding latch correctly with the lock so as not to damage the lock itself when opening and closing the door. Preferably this is a one-person process using an alignment jig. The alignment jig is designed for a standard size 650 Janus guide rail using a standard hole. If the door being installed is not this conYiguration, the installer may need to use a two-person installation method with one installer inside and another outside. To install the lock, 1. Key components for using Alignment Jig 2. Open the door and insert the Alignment Jig into the Guide Rail. Place in the railing so the Alignment Post is INSIDE the Guide Rail Hole.
Page 14 Nokē Ion Install Guide (Internal Use Only) 3. The jig is now in posi?on to drill the Nokē Ion Moun?ng Holes for the two Carriage Bolts. Use a 17/64” drill bit and posi?on inside the Bushings in the Alignment Jig and drill your holes.
Page 15 Nokē Ion Install Guide (Internal Use Only) 7. Align the lock over the drill holes and insert the carriage bolt into the bohom hole and loosely ?ghten. This temporarily holds the lock in place which lets you easily ahach the power supply, Wirepas antenna, and cables out in the open.
Page 16 Nokē Ion Install Guide (Internal Use Only) Op.onal: If you are installing Interface Module, you will need to remove the Nokē Ion Wire Harness from the 10-Pin Connector so you will be able to plug in the 10-Pin to 10-Pin Extender Cable w/ LED Breakout.
Page 17: Installing The Led Light Assembly (Op?Onal)
Nokē Ion Install Guide (Internal Use Only) Installing the LED Light Assembly (Op?onal) The 4-pin LED light assembly is an optional installation that requires drilling through the door frame. It is only used to indicate the status of the lock: Locked/Unlocked/Updating. Before you begin installing the LED light, it is important to measure and mark the height on the door frame where you will drill the 1” OD access hole centered 50” above Yinished Yloor (AFF) and 3” from the edge of the door opening on the door jamb. This will ensure that the LEDs are uniformly placed throughout the installation for the facility. LED Light Assembly To install the Status LED OPTION 1: Sheet metal frame building 1. Mark and drill the 1” OD access hole for the LED light assembly into the face of the door frame centered at 50”...
Page 18 Nokē Ion Install Guide (Internal Use Only) 4. From inside the unit, remove the back cover from the LED housing, and then feed the threaded nut end over the 4-pin wiring and carefully twist it onto the threaded LED light un?l it is hand ?ght.
Page 19: Installing The Interface Module (Op?Onal)
Nokē Ion Install Guide (Internal Use Only) Installing the Interface Module (Op?onal) The interface module is installed into a unit if the unit is meant to be using the Daisy-Chain power concept (used more commonly on external units), if the unit is meant to have a Motion Sensor installed, or both. The interface module helps move the cables into a simpler conYiguration to help the installer, and it also reduces some cable lengths to reduce power losses. Finally, the interface module helps simplify what cables are being installed into the Nokē Ion main lock body, which is important because volume inside that electronics cavity is limited. Interface Module Assembly To install the Interface Module, 1. 10-Pin Interface Module Cable Ends: 2. Connectors on the PCB are used as follows: Revised 10/22/24...
Page 20 Nokē Ion Install Guide (Internal Use Only) 3. Start a 4” small zip ?e around the 10-Pin Cable Tie-Oﬀ. Insert the Interface Module End of the 10-Pin cable connector through this zip ?e and into the Interface Module main body. Align and connect with its ma?ng connector on the PCB.
Page 21 Nokē Ion Install Guide (Internal Use Only) the PCB from the 10-Pin connector. If no Mo?on Sensor is used in this unit, just leave this connector empty. 6. Feed all the cables around the columns in the center of the Interface Module. Once the cables are all placed correctly, install the Cable Cover using the included screw.
Page 22 Nokē Ion Install Guide (Internal Use Only) 8. On the Nokē Ion Lock Body, remove the Short Wire Harness that comes standard with the Nokē Ion and insert the Lock Body End w/ LED Breakout into its place on the PCBA. 9.
Page 23: Installing The Mo?On Sensor (Op?Onal)
Nokē Ion Install Guide (Internal Use Only) Installing the Mo?on Sensor (Op?onal) The Motion Sensor is an optional installation for mounting a sensor that can detect if a person is inside the unit. The sensor will provide this information to the Nokē Ion lock which is then passed to the cloud and can be used for data analysis, customer notiYication, etc. This installation is meant to be Yinished before the Interface Module has been mounted to the unit. Motion sensor should be mounted at ~8ft (2.4m) off the ground MoNon Sensor Assembly To install the Mo.on Sensor, 1. Drill or knock-out a hole for the Sensor Moun?ng Screw and the Cable Feed-Through hole. 2.
Page 24 Nokē Ion Install Guide (Internal Use Only) 4. Pre-drill a pilot hole in the sheet metal where you would like the BOTTOM moun?ng screw to be located. The top can be pre-drilled now, or you can use a sheet metal screw and screw it in at a later step.
Page 25 Nokē Ion Install Guide (Internal Use Only) 8. Hold it up in the unit so the lower screw hole aligns with the pilot hole. Screw the lower screw into the sheet metal. 9. Rotate the Sensor Body right-side-up. Orient the Sensor unit so that it is facing correctly into the unit (approximately diagonally across the unit or 45 degrees from the wall for oddly shaped units).
Page 26 Nokē Ion Install Guide (Internal Use Only) 12. Connect the 4-pin Connector on the other end of the Sensor cable into the Interface Module (see the Installing the Interface Module (Op.onal) sec?on on Page 1616). Clean up cables and securely mount so they are not at risk of being damaged by future tenants of the storage unit. 13.
Page 27: Tes?Ng The Locks
Nokē Ion Install Guide (Internal Use Only) Tes?ng the Locks After installing a section of locks at the facility, go back through and test each of the locks one more time via the Noke ̄ Storage Smart Entry manager’s mobile app. To test a lock, 1. Open your Nokē Storage Smart Entry manager’s mobile app, and then tap + (top-right corner). 2. Tap the Units icon at the bohom of the screen. 3.
Page 28: Maintenance
Nokē Ion Install Guide (Internal Use Only) Maintenance Inspect the entire facility for tampering or damage at the end of the installation. Disclaimer Always install all network and devices in a safe manner and in full compliance with this manual and any applicable laws related thereto. No warranties express or implied are contained herein. Nokē or Janus International is not liable for any injuries or damages to any operators, property, or bystanders incurred as a result of using the networking devices by its customers. Nokē or Janus International also cannot be held liable for any and all errors in this manual or for any incidental or consequential damages that result for the use of the material presented in this manual. This manual contains proprietary information belonging solely and exclusively to Nokē and Janus International. All rights are reserved. No part of this manual may be photocopied, reproduced, or translated to another language without the written consent of Nokē or Janus International. Contact Us Toll Free: (833) 257-0240 Nokē Smart Entry Support: Email: smartentrysupport@janusintl.com Website: www.janusintl.com/products/Nokē Revised 10/22/24...
Page 29: Compliance Statement
Nokē Ion Install Guide (Internal Use Only) Compliance Statement Nokē Ion FCC ID 2AFRJ-ION1 IC 32315-ION1 FCC Compliance Statements This device complies with Part 15 of the FCC Rules. OperaGon is subject to the following two condiGons: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operaGon.
Page 30 Nokē Ion Install Guide (Internal Use Only) MoGon Sensor FCC Compliance Statements This device complies with Part 15 of the FCC Rules. OperaGon is subject to the following two condiGons: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operaGon.