Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for SmartPool EcoSmart 400
- Page 1 EcoSmart 400 User Guide v1.1...
-
Page 3: Table Of Contents
TABLE OF CONTENTS Installing the device................4 Quick start guide ................5 Connect to Wifi ..................5 Add your devices ...................6 The main screen................. 7 Setting timers ..................8 Setting Timers from the Hub..............8 Special timers for your ecosmart controller........9 Setting timers from your phone ............10 Weather tab ..................11 Energy tab ..................12 EcoSmart hub settings ..............12... -
Page 4: Installing The Device
INSTALLING THE DEVICE 1. Mount the device close to your pool plant pipework so that you can install the temperature sensor in or against the water pipe. 2. The temperature sensor can be attached by mounting it to the surface of the water pipe. If choosing this method, you must carefully insulate the temperature sensor to ensure it measures the water temperature as accurately as possible. -
Page 5: Quick Start Guide
QUICK START GUIDE CONNECT TO WIFI 1. In your plant room, power on your SmartPool and connect to the SP400 hotspot using your mobile phone. 2. Open a web browser and connect to SP400.local, tap the Menu (hamburger icon top left) and select WiFi. -
Page 6: Add Your Devices
ADD YOUR DEVICES 1. Tap the DEVICES tab at the top of the hub screen. 2. With your first smart plug powered on in your pool house close to your hub, tap the Switch next to the device you wish to connect, e.g. Pump as shown in the picture. 3. -
Page 7: The Main Screen
THE MAIN SCREEN From the MAIN screen of your hub you can view the status of connected devices, the power consumption and pool temperature. You can also turn the connected devices on and off and switch on/off the timer control. Note: if you have the timer activated and you tap to manually control a device, it will disable the Timer Control. -
Page 8: Setting Timers
Timers may be set from the hub unit or from your phone. SETTING TIMERS FROM THE HUB On your SmartPool Hub, tap the TIMER tab at the top of the screen. You may need to tap the screen to “wake” it from power save mode. -
Page 9: Special Timers For Your Ecosmart Controller
SPECIAL TIMERS FOR YOUR ECOSMART CONTROLLER There are two special timers which you can use to add Smart Timer functions to your devices. These require that you have entered a location for your device in SETTINGS (see Settings section) so that the correct weather forecast information can be used. -
Page 10: Setting Timers From Your Phone
To set a sunset based timer: 1. Tap the switch to turn on Period 3. 2. Ignore the start time as this will be set for you each day. Tap the On at Sunset switch. 3. Tap the Stop Time for Period 3 and select the time to switch off using the hour and minute rollers. -
Page 11: Weather Tab
WEATHER TAB The WEATHER tab is for information only. It allows you to see the part of the day the “Smart” controller will use to start and stop the devices you have connected using the EcoSmart Timer functions. If you touch and hold the Thermometer icon you will see the optimum time of day to run heat pumps. -
Page 12: Energy Tab
ECOSMART HUB SETTINGS The SETTINGS tab is where you configure your SmartPool for your specific location. WHEN YOU HAVE COMPLETED YOUR SETTINGS MAKE SURE TO... -
Page 13: System Clock
You can rename the auxiliary devices to a more relevant name, e.g. Fountain. FREEZE PROTECT Tap this to enable your SmartPool to automatically turn on the pump when the temperature drops below 4 degrees centigrade. TEMPERATURE CONTROL Auxiliary 1 may be used to control your pool heating system. You will need to consult your pool installation engineer to connect it to the heater controller. -
Page 14: Changing The Settings From Your Phone
Temperature Set Point. When the temperature is below the set point the SmartPool will turn on the Aux1device which you have connected to your heater. It is suggested that you name Aux1 ‘Heater’ to make it clear. -
Page 15: Remote Control
If you are using the Internet connection you can only control the pool devices and set timers. Internet remote can be set in ‘view only’ mode or ‘full control’. Each SmartPool hub has a unique ID which you should not share, to ensure that nobody else can access the pool control via the Internet. -
Page 16: Alexa Control
Once the hub has restarted you will need to configure Alexa to connect to the SmartPool. For this to work, your SmartPool and your Alexa device will need to be on the same WiFi network. To make the connection, simply ask Alexa to discover your devices by saying “Alexa, Discover Devices”. -
Page 17: Updating Software
You will need a very reliable WiFi connection and steady power supply to ensure that the update completes successfully. Read and follow the instructions on the SmartPool Support page to ensure there are no errors. Enter the following URL into your web browser and click on the Software update page for “SmartPool EcoSmart 400”. -
Page 18: Troubleshooting
TROUBLESHOOTING 1. POOR CONNECTIVITY The key to a reliable SmartPool operation is good WiFi connection. If the WiFi is not reliable in your pool house then the addition of a WiFi repeater will probably fix it. Low cost devices are available from any online retailer.
Need help?
Do you have a question about the EcoSmart 400 and is the answer not in the manual?
Questions and answers