Bionaire BCM6100 Instruction Leaflet

BCM610005EFM1.qxd 5/23/05 9:23 Page 1
HUMIDIFIER SAFETY
PLEASE READ AND SAVE
BEDROOM
cool moisture
THESE IMPORTANT SAFETY
humidifier
INSTRUCTIONS
BCM6100
MODEL
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions
should always be followed to reduce the risk of fire, electric
shock, and injury to persons, including the following:
1.Read all instructions before using the appliance.
2.To avoid fire or shock hazard, plug the appliance directly
into a 120V AC electrical outlet.
3.Keep the cord out of heavy traffic areas. To avoid fire hazard,
NEVER put the cord under rugs or near heat registers.
4.DO NOT place humidifier near heat sources such as
stoves, radiators, and heaters. Locate your humidifier on
an inside wall near an electrical outlet. The humidifier
should be at least 4" away from the wall for best results.
5.NEVER place humidifier in an area where it is accessible
to children. NEVER use humidifier in a closed room,
particularly where a child may be sleeping, resting, or
playing (a closed room may result in excessive humidity).
6.WARNING: Do not attempt to refill humidifier without first
unplugging the unit from its electrical outlet. Failure to
heed this warning may cause personal injury. Be sure to
unplug the unit by pulling on the plug and not the cord.
7.Never place anything over moisture outlet when the unit
is running.
8.NEVER drop or insert any object into any openings
unless instructed in this manual.
9.DO NOT operate any appliance with a damaged cord or
plug, after the appliance malfunctions, or if it has been
dropped or damaged in any manner. Return appliance to
manufacturer for examination, electrical or mechanical
adjustment, or repair.
10.Use appliance only for intended household use as
described in this manual. Any other use not recom-
mended by the manufacturer may cause fire, electric shock,
or injury to persons. The use of attachments not recom-
mended or sold by the manufacturer may cause hazards.
Filter: WF6000
11.DO NOT use outdoors.
Read instructions before operating. Retain for future reference.
12.Always place humidifier on a firm, flat, level surface. A water-
Instruction Leaflet
proof mat or pad is recommended for use under the humid-
ifier. NEVER place it on a rug or carpet, or on a finished floor
that may be damaged by exposure to water or moisture.
INFO-LINE
13.DO NOT allow the Moisture Outlet to directly face the wall.
If after having read this leaflet, you have any questions
Moisture could cause damage, particularly to wall paper.
or comments on your humidifier,
14.Humidifier should be unplugged when not in use.
call 1-800-253-2764 in North America.
REPLACING THE WICK FILTER DAILY MAINTENANCE
To replace the wick filter, follow the steps below. 1. Before cleaning, set the mode to the OFF position and
unplug the unit from the electrical outlet.
Through normal use, waterborne minerals and sediment
become trapped in the wick filter. The harder your water, 2. Lift off the water tank and the humidifier housing.
the greater the amount of minerals in the water, and the
3. Carry the base and the water tank to the sink, remove
more often you will need to change your wick filter. You
the filter, then drain and rinse the base and water tank
will be able to check the life of the filter on your humidifier
thoroughly to remove any sediment and dirt. Wipe
by checking the Filter Monitor located on the moisture
clean and dry with a clean cloth or paper towel.
outlet. When the unit is not in operation, the Filter Monitor
4. Put the filter back in the unit, replace the humidifier
will also read as OFF. When the unit is turned on, the
housing, then refill the water tank with cool tap water as
Filter Monitor needle will need 60 minutes to read the
instructed under "Filling the Water Tank".
current filter condition. If the needle reads change after
60 minutes, then filter replacement is needed. Regular fil-
5. If moisture forms on the walls or windows, turn off the
ter replacement is necessary to ensure optimal humidifier humidifier.
performance.
1. Turn the unit off and unplug the humidifier from the WEEKLY MAINTENANCE
electrical outlet.
Remove scale:
2. Open the filter housing using the tab on the left side of
1. Repeat steps 1-3 above.
the filter door.
2. Clean the base by partially filling the base with one 8-oz
3. Discard the old wick filter and insert a new wick filter
cup of undiluted white vinegar, or use Clean-Away
into the hanging tabs.
Bionaire ® . Let solution stand 20 minutes, cleaning all
4. Repeat "Operating Instructions" steps listed within. it the interior surfaces with a soft brush. Dampen a cloth
with undiluted white vinegar and wipe out entire base to
will take about 30 minutes for the humidifier to reach
maximum output. remove scale.
3. Rinse with clean warm water to remove scale and the white
You can obtain your filter model by calling
1-800-253-2764 in North America or by visiting your vinegar solution before beginning to disinfect the tank.
nearest retailer or authorized service center. This
humidifier takes model WF6000 replacement filter. DISINFECT TANK:
1. Fill water tank with 1 teaspoon of chlorine bleach and 1
CLEANING AND MAINTENANCE INSTRUCTIONS
gallon of water.
Humidifiers provide comfort by adding moisture to dry,
2. Let the solution stand for 20 minutes, swishing every
heated indoor air. To get the most benefit from the
few minutes. Wet all surfaces.
humidifier and avoid product misuse, follow all instruc-
3. Empty the reservoir after 20 minutes, and rinse well
tions carefully, specifically the operation, care and mainte-
with water until the bleach smell is gone. Dry with a
nance guidelines. Please note that this is an electrical appli-
clean cloth or paper towel.
ance, and requires attention when in use.
4. Check to see if it is time to change the wick filter.
In addition, if you do not follow the recommended care and
maintenance instructions, micro-organisms may be able to 5. Refill the water tank with cool water, replace the humidi-
grow in the water within the humidifier's water tank. fier housing and the water tank. Repeat Operating
Instructions.
The length of cord used on this appliance was selected to
15.NEVER tilt, move, or attempt to empty unit while it is
operating. Shut off and unplug before removing the reduce the hazards of becoming tangled in, or tripping
water reservoir and moving the unit. over a longer cord. If a longer cord is necessary an
16.This humidifier requires daily and weekly maintenance to approved extension cord may be used. The electrical rat-
ing of the extension cord must be equal to or greater than
operate appropriately. Refer to daily and weekly cleaning
procedures. Use only cleaners and additives recom- the rating of the humidifier. Care must be taken to arrange
mended by the manufacturer. the extension cord so that it will not drape over the coun-
tertop or tabletop where it can be pulled on by children or
17.NEVER use detergents, gasoline, glass cleaner, furniture
polish, paint thinner, or other household solvents to accidentally tripped over.
clean any part of the humidifier.
This device complies with Part15 of the FCC Rules.
18.Excessive humidity in a room can cause water conden- Operation is subjected to the following two conditions: (1)
sation on windows and some furniture. If this happens,
this device may not cause harmful interference, and (2)
turn the humidifier OFF.
this device must accept any interference received, includ-
19.Do not use humidifier in an area where humidity level is ing interference that may cause undesired operation.
in excess of 50%. Use a hygrometer, available at your
Modifications not authorized by the manufacturer may
local retailer or through the manufacturer, to measure the
void user's authority to operate this device.
humidity.
20.DO NOT attempt to repair or adjust any electrical or
HOW YOUR COOL MOISTURE HUMIDIFIER WORKS
mechanical functions on this unit. Doing so will void your
warranty. The inside of the unit contains no user service- Your Bionaire ® Cool Moisture humidifier draws dry air
able parts. All servicing should be performed by qualified through the front air intake grill area. This air is then
personnel only. passed through a moisture–laden wick filter which retains
21.Never place housing under water flow or immerse in the minerals and deposits. The resulting moist air is
liquids. directed back into the room from the top air grill.
22.Do not plug in the cord with wet hands: electric shock
Tip: This humidification system provides a cool, invisi-
could result.
ble moisture
23.Do not pour water in any openings other than the water
output. It is normal not to see the mist.
reservoir.
24.To prevent damage to surfaces, do not place humidifier
PRE-OPERATING INSTRUCTIONS
under overhanging surfaces.
1. Be sure the humidifier is switched off and disconnected
25.NEVER operate unit without water in the reservoir.
from the electrical outlet.
26.Do not move unit after it has been used until unit cools
2. Select a location for your humidifier, on a flat surface,
completely.
about 4" away from the
27.Use both hands when carrying full reservoir of water.
wall. Do not place your
PLEASE SAVE THESE humidifier on furniture, a
floor location that will not
INSTRUCTIONS.
be damaged by mois-
ture is best.
CONSUMER SAFETY INFORMATION
3. Remove the water tank,
THIS PRODUCT IS EQUIPPED
by holding the tank han-
WITH A POLARIZED AC (a plug
dle and lifting straight
having one blade wider than the
upwards.
other). This plug will fit into the
4. Remove the filter door
power outlet only one way. If the
by pulling the tab
plug does not fit fully into the
straight out. Check to see
outlet, reverse the plug. If it still does not fit, contact qual-
that the wick filter is
ified personnel to install the proper outlet.
properly in place. Replace
the humidifier filter door.
DO NOT DEFEAT THE SAFETY PURPOSE OF THIS
POLARIZED PLUG IN ANY WAY.
STORAGE INSTRUCTIONS Fig. 4
If your humidifier will not be in use for two days or more,
Trouble Shooting for your Cool Mist Humidifier
or at the end of the season follow these instructions.
Trouble Probable Cause
1. Clean and dry the humidifier thoroughly as per the
• Mist output minimal to Filter has not
none. absorbed water.
"Weekly Maintenance" instructions.
Mineral buildup in base.
2. Let the humidifier dry completely before storing. Do not
store with water inside the base or water tank.
Humidistat is set too low.
3. Remove the tank cap. Do not store with the tank cap in
Wick Filter needs
place.
to be replaced.
4. Store in a cool dry location.
Normal operation.
SERVICE INSTRUCTIONS
• Water leaks from water Rubber O-ring is missing
1. Do NOT attempt to repair or adjust any electrical or
reservoir. or improperly placed.
mechanical functions on this unit. Doing so will void the
Tank Cap not
Warranty. The inside of the unit contains no user serv-
tight enough.
iceable parts. All servicing should be performed by
• Water Filter turns brown. Your filter needs
qualified personnel only.
to be changed.
2. If you need to exchange the unit, please return it in its
In areas with hard water
original carton, with a sales receipt, to the store where
TM by your wick filter will need
to be changed frequently.
you purchased it. If you are returning the unit more than
30 days after the date of purchase, please see the
Mineral deposits cause
• Film on water reservoir.
enclosed Warranty.
film on tank to build up.
3. Should your humidifier require service, please call
1-800-253-2764 in North America for further assis-
Filter needs
• Water cloudy.
tance. to be replaced.
Using warm water
to refill water tank.
4 . If you have any other questions or comments, feel
free to write to us or visit our website Humidifier is reacting
• Humidistat cycles on/off.
to room humidity level.
www.bionaire.com
Over tightened.
• Very tight reservoir cap.
The Holmes Group, Inc.
Consumer Service Department
13052 Jurupa Avenue
Fontana, CA 92337
FILLING THE WATER TANK MANUAL OPERATION WITH REMOTE
1. Twist off the water tank cap located on the bottom of 1. Press Mode button on the remote. "High" illuminates on
the water reservoir by turning counter clockwise and fill
the water tank with cool, fresh water. Do not fill with
warm water as this may cause leaking.
2. After filling the water tank, replace the water tank cap
by firmly turning clockwise and then replace the water 2. Press Mode button on remote a second time for "Med"
reservoir on the base. The water reservoir will immedi-
ately begin to empty into the base.
Note: While using the remote, the backlight function will
turn on when any button is pushed and will turn off after
FIRST USE ONLY 10 seconds of non-use.
1. Put batteries into Remote. The "Room" humidity will be
Note: Do not block ventilation openings on remote while in
displayed at all times. (Use 3 AAA Alkaline batteries
use, this may affect the accuracy of the humidity reading.
only, do not mix batteries)
2. Plug unit into outlet. The first time the unit is plugged in,
HUMIDISTAT OPERATION WITH REMOTE
it will beep every two seconds until it is synced with the
1. Press Mode button on remote until the remote screen
remote. To sync unit with remote follow the below
steps:Unlock remote. (This must be done before
each use of the remote) To Unlock remote, hold
down the mode button for 2 seconds until the lock
symbol disappears on the screen. Once the remote
is unlocked, press the mode button again and the unit
will quickly beep 5 times telling the user the signal was
received. If you have more than one humidifier, DO
2. Press Mode button on remote again for "Med" and
NOT SYNC more than 1 unit at once.
Battery Replacement: If the batteries are running low
on power, a low battery indicator will appear on the
remote. Low batteries will affect transmission distance
3. To turn unit "Off", press the Mode button and the LCD
and the screen contrast. We recommend replacing bat-
teries immediately.
Remote Distance: The transmission distance for this
remote is approximately 30ft. Do not use farther than
G 30ft. from the appliance. Remote must be used in same
Fig 1 C
D
room as appliance.
B
Communication Safety Check: Every minute while in
Note: It is normal for the
E Auto mode, the Galileo ® Center communicates with the
humidifier to cycle on and off
base unit. If the Galileo ® Center goes out of range and/or
as it maintains the preset
has low batteries, the communication will stop, and after
humidity.
8 minutes of non-communication the unit will shut off.
A
Fig 2
ADJUSTING SET HUMIDITY:
F 1. When in "Auto" mode, press the (+) or (-) buttons on
A. Humidifier Tank
mode
B. Carry Handle
C. Filter Monitor
D. Humidifier Housing
E. Filter Door
F. Humidifier Base
G. Control Panel
Fig. 5 WARRANTY
The Manufacturer warrants to the original retail purchaser, for
FREQUENTLY ASKED QUESTIONS
TWO (2) YEARS from the date of original purchase, either to
Solution Question Answer
repair or replace at its option, without charge (parts and
• What are the variables that The estimated run time for this humidifier is based on aver
Wait 15 minutes before
starting humidifier. affect run time? age room conditions. The actual run time of your humidifier labor), any supplied or manufactured part of this humidifier
Regular cleaning of tray is dependent on numerous variables such as:
which, upon inspection by an authorized service center,
Air exchange in the room where the humidifier is placed.
after each use will help
proves to have failed in normal use due to defects in material
keep the unit functioning
properly. Room construction of the room where the humidifier is placed.
or workmanship, or, at its option, to replace the unit.
Set the humidistat to
Temperature of the room where the humidifier is placed.
high.
Operation under conditions other than those recommend-
Replace your wick filter
(WF6000) by calling Humidity levels in the room where the humidifer is placed.
ed or at voltages other than the voltage indicated on the
1-800-253-2764, or visit
Movement of occupants and the opening and closing of unit, or any attempts by unauthorized personnel to service
www.bionaire.com.
Mist is invisible. doors in the room where the humidifier is placed.
the unit or modify it, will render the guarantee void.
Check to see if inlet or
Home furnishings in the room where the humidifer is placed.
outlet grills are blocked.
The Manufacturer shall not be liable for any personal injury,
Remove tank
• How do I remove film on See Daily Maintenance instructions. Regular cleaning is property damage or any incidental or consequential dam-
cap then replace
water tank? recommended.
ages of any kind, resulting from defects, malfunctions, mis-
or reposition ring.
Tighten the • How can I extend the run Run your unit on the lowest setting.
use, improper installation or alteration of the product.
tank cap.
time?
If your unit has electronics, set it to your desired humidity
THE MANUFACTURER EXPRESSLY DISCLAIMS ALL
Replace your wick filter
level. The unit will turn on and off, which will extend the run
(WF6000) by calling
time.
1-800-253-2764, or visit
www.bionaire.com.
Fill the tank all the way full, place it on the base, let the
Use Clean Away TM Solution
water empty into the base until it stops bubbling, then refill
(DMS216), to order call
the tank full again. This ensures maximum water capacity
1-800-253-2764, or visit
and will extend run time.
The provisions of this Warranty are in addition to, and not
www.bionaire.com.
a modification of, or subtraction from the statutory
Replace your wick filter
warranties and other rights and remedies contained in
(WF6000) by calling
1-800-253-2764, or visit
any applicable legislation and to the extent that any such
www.bionaire.com.
provision purports to disclaim, exclude or limit any such
Refill using cool water.
statutory warranties or other rights or remedies, such pro-
visions shall be deemed to be amended to the extent
necessary to comply therewith.
Set the humidistat to a
higher or lower setting.
Add liquid soap or
petroleum jelly to cap
gasket to ease opening.
A consumer service representative will help determine
which is the best procedure in order for your humidifier to
be repaired.
KEEP THIS NUMBER FOR FUTURE REFERENCE.
Bionaire
The Holmes Group, Inc.
EXTENDED RUN TIME SETTING:
By setting you humidifier to a specific humidity level, you
remote screen indicating mode. The power light on the
are actually also extending the run time. Since the unit will
unit will turn on. The unit turns on and operates in
turn on and off to maintain the set humidity level, less
"High" mode. The units "High" light will illuminate. In this
water will be used, so you will need to fill the unit less
mode, the unit will continuously run at its high setting.
than you would on manual setting.
mode and once again for "Low" mode.
UNIT OPERATION WITHOUT REMOTE
Your humidifier can be operated directly from the control
panel located on the top of the unit
A. Remote and Unit are OFF:
1. Press the Mode button on the unit the first
time.The "High" light illuminates and the unit runs
in "High" mode. The power light turns on.
2. Press the Mode button a second time to run in
"Med" mode.
displays "Auto" and "High". The "Set" humidity is dis-
3. Press the Mode button again to run in "Low" mode.
played next to the "Room" humidity. The "Auto" light on
4. Press the Mode button again and the unit shuts off.
unit will illuminate. The unit will cycle on and off to main-
tain the "Set" humidity at high setting. NOTE: The
Note: The "auto" light only illuminates when the unit is
default room humidity is 45%. In this mode the unit will set to "auto" mode by the remote.
run to maintain the "Set" humidity.
B. Remote is ON and Unit is ON:
1. Press the Mode button on the unit. The unit will
"Auto", and again for "Low" and "Auto". The unit will
then switch "Modes"; either from "High" to "Med",
cycle on and off to maintain the "Set" humidity at the
"Med" to "Low", or "Low" to "Off". The unit's
designated setting.
lights will reflect the change.
The Remote will display a different mode – the mode in
will go blank (except for
which it was left. If a button is pressed on the Remote,
Fig 3 Filter Monitor
the "Room" humidity dis-
the Remote's signal will override the "Mode" on the unit
play which is always dis-
and the two will be back in sync.
played while batteries are
Low
in the remote) and the unit
Med
TIMER FUNCTION:
will shut off.
Using Timer to Turn Unit Off
1) Hold mode button for 2 seconds to unlock remote.
Auto
High
2) Push + and - together.
Mode
2.1) "timer" turns on. 1 Hr appears on the screen.
3) Push + or - to adjust the number of hours the unit will
run before it automatically shuts itself off.
3.1) you can choose from; 1 to 8 hours
the remote. The "Set" number will increase or decrease
with each press. Hold the button down to scroll. The 3.2) 1 through 8 will scroll in a continuous loop
minimum humidity is 35% and the maximum is 60%.
4) After you have made your selection, the whole screen
The unit scrolls one digit at a time in a continuous loop.
flashes for 5 seconds after last button push of + or -
35%, 36%..., 59%, 60%, 35%, 36%....
then goes back to previous mode
4.1) "timer" remains lit to show the timer function has
been set.
RESPONSIBILITY FOR CONSEQUENTIAL
DAMAGES OR INCIDENTAL LOSSES CAUSED
BY USE OF THIS PRODUCT.
FOR WARRANTY SERVICE, PLEASE CALL
1-800-253-2764 IN NORTH AMERICA.
® the Bionaire logo ® , Galile ® and Clean-Away™ are trademarks of
Printed In China
5) At any time if you unlock the remote and push the
mode button to turn the unit off, the timer setting
will be erased and "timer" will disappear from the
remote.
6) To check how much time is remaining, press and hold
the + and – buttons simultaneously.
Using Timer to Turn Unit On
This function is meant for a person to pre-humidify a
room by setting the timer. For Example: It's 8 am, and
you want to come home to a humidified room at 8 pm.
To accomplish this place the unit in the desired room and
set the timer to turn the unit on in 12 hours. Once the
timer is activated the unit will run for a preset time of 2
hours.
1) Hold mode button for 2 seconds to unlock remote.
2) DO NOT push mode again as this will turn unit on.
3) Push + and - together.
3.1) Unit remains off.
3.2) "timer" and "auto - high" turns on and flashes on
the remote, and 1 Hr appears on the screen.
4) Push + or - to adjust the number of hours that will pass
before it turns itself on.
4.1) you can choose from; 1to16 hours
4.2) 1 through 16 will scroll in a continuous loop
5) The whole screen flashes for 5 seconds after last but-
ton push of + or - then goes back to previous mode
5.1) The timer will turn the unit on and run for 2 hrs.
During the 2 hours, the digital humidistat will main
tain the room in auto – high at the default of 45%.
6) At any time if you unlock the remote and push the
mode button on the remote, the timer setting will
be erased and "timer" will disappear from the
screen.
7) To check how much time is remaining, press and hold
the + and – buttons simultaneously.