Bionaire BCH4230-CN Instruction Leaflet

BCH4830-CN_08EFM1.qxd :126461/9100020009151 5/14/08 10:54 AM Page 1
Oscillating Twin Ceramic
Heater
When using electrical appliances, basic safety
precautions should always be followed to reduce the risk
BCH4830-CN
MODEL
of fire, electric shock, and injury to persons, including the
following:
1. Read all instructions before using the appliance.
2. To avoid fire or shock hazard, plug the appliance
directly into a 120V AC electrical outlet.
3. The heater is hot when in use. To avoid burns, DO NOT
let bare skin touch hot surfaces. If provided, use
handles when moving this heater. Keep combustible
materials, such as furniture, pillows, bedding, papers,
clothes, and curtains at least 3 ft (0.9 m) from the front
of the heater and keep them away from the sides and
rear.
4. DO NOT run cord under carpeting. DO NOT cover cord
with throw rugs, runners, or the like. Arrange cord away
from traffic area and where it will not be tripped over.
5. This heater is not intended for use in bathrooms,
laundry areas and similar indoor location. NEVER locate
heater where it may fall into a bathtub or other water
container.
6. Extreme caution is necessary when any heater is used
by, or near children or invalids, and whenever the
heater is left operating and unattended.
7. Always unplug the heater when not in use.
8. When unplugging, be sure to pull by the plug and not
the cord.
9. DO NOT insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause an
electric shock or fire, or damage the heater.
10.DO NOT operate heater with a damaged cord or plug,
or after the heater malfunctions, has been dropped or
damaged in any manner. Return appliance to
manufacturer for examination, electrical or mechanical
adjustment, or repair.
Read instructions before operating.
11.A heater has hot and arcing or sparking parts inside.
Retain for future reference.
DO NOT use it in areas where gasoline, paint, or
Instruction Leaflet
flammable liquids are used or stored.
12.Use appliance only for intended household use as
¤
described in this manual. Any other use not
INFO-LINE
recommended by the manufacturer may cause fire,
If after having read this leaflet, you have any
electric shock, or injury to persons. The use of
questions or comments on your heater,
attachments not recommended or sold by the
call 1-800-253-2764 in North America.
manufacturer may cause hazards.
13.DO NOT use outdoors.
126461/9100020009151
Sunbeam Products, Inc. doing business as Jarden
Consumer Solutions or if in Canada, Sunbeam
• UNPLUG THE UNIT.
Corporation (Canada) Limited doing business as Jarden
• Make sure the electrical outlet or circuit breaker is
Consumer Solutions (collectively "JCS") warrants that for a
working.
period of three years from the date of purchase, this
product will be free from defects in material and
• Check for obstructions. If you find an obstruction turn
workmanship. JCS, at its option, will repair or replace this
the heater OFF, and follow the Reset Instructions in the
product or any component of the product found to be
manual. Carefully remove the obstruction.
defective during the warranty period. Replacement will be
• The temperature might be set too low. Press the
made with a new or remanufactured product or
Mode/Off button until the heater restarts.
component. If the product is no longer available,
replacement may be made with a similar product of equal
or greater value. This is your exclusive warranty. Do NOT
• Make sure the oscillation button is pressed.
attempt to repair or adjust any electrical or mechanical
• Make sure nothing is wedged between base and body.
functions on this product. Doing so will void this warranty.
This warranty is valid for the original retail purchaser from the
date of initial retail purchase and is not transferable. Keep
the original sales receipt. Proof of purchase is required to
If you have any questions regarding your product or
obtain warranty performance. JCS dealers, service centers,
would like to learn more about other Bionaire ® products,
or retail stores selling JCS products do not have the right to
please contact our Consumer Service Department at
alter, modify or any way change the terms and conditions of
1-800-253-2764 or visit our website at www.bionaire.com.
this warranty.
This warranty does not cover normal wear of parts or
damage resulting from any of the following: negligent use or
misuse of the product, use on improper voltage or current,
use contrary to the operating instructions, disassembly, repair
or alteration by anyone other than JCS or an authorized JCS
service center. Further, the warranty does not cover: Acts of
God, such as fire, flood, hurricanes and tornadoes.
JCS shall not be liable for any incidental or consequential
damages caused by the breach of any express, implied or
statutory warranty or condition.
Except to the extent prohibited by applicable law, any
implied warranty or condition of merchantability or fitness
for a particular purpose is limited in duration to the dura-
tion of the above warranty.
JCS disclaims all other warranties, conditions or represen-
tations, express, implied, statutory or otherwise.
JCS shall not be liable for any damages of any kind result-
ing from the purchase, use or misuse of, or inability to use
the product including incidental, special, consequential or
similar damages or loss of profits, or for any breach of
contract, fundamental or otherwise, or for any claim
brought against purchaser by any other party.
Some provinces, states or jurisdictions do not allow the
exclusion or limitation of incidental or consequential dam-
ages or limitations on how long an implied warranty lasts,
so the above limitations or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may
also have other rights that vary from province to province,
state to state or jurisdiction to jurisdiction.
14.To prevent a possible fire, DO NOT block air intakes or
exhaust in any manner. DO NOT use on soft surfaces,
like a bed, where openings may become blocked.
This heater is equipped with a patented, technologically-
15.To disconnect heater, turn controls to OFF, then remove
advanced safety system that requires the user to reset
plug from outlet.
the heater if there is a potential overheat situation. When
a potential overheat temperature is reached, the system
16.Avoid the use of an extension cord because the
will automatically shut the heater off. It can only resume
extension cord may overheat and cause a risk of fire.
operation when the user resets the unit. For specific reset
However, if you have to use an extension cord, the
instructions please refer to the unit.
cord shall be No. 14 AWG minimum size and rated not
less than 1875 watts.
17.If the heater will not operate, see specific instructions
If the unit shuts down:
on Auto Safety Shut-off.
1. Unplug the unit.
18.DO NOT attempt to repair or adjust any electrical or
mechanical functions on this unit. Doing so will void 2. Wait 30 minutes for the unit to cool down.
your warranty. The inside of the unit contains no user
3. Plug in and operate normally.
serviceable parts. All servicing should be performed by
NOTE: To shut unit OFF, hold Mode/Off button down for 2
qualified personnel only.
seconds.
19.Discontinue use if plug or outlet is hot. It is
recommended that the outlet be replaced if plug or
outlet is hot to touch.
When the unit is accidentally knocked over, it will instantly
shut off. To reset, simply place the heater in an upright
position. Press Mode/Off button and operate normally.
1. Carefully remove your heater from the box. please save
the carton for off-season storage.
THIS APPLIANCE HAS A POLARIZED
2. Make sure the unit is in the OFF position before
AC PLUG (one blade is wider than the
plugging the heater into the outlet.
other). To reduce the risk of electric
shock, this plug is intended to fit in a 3. Place heater on firm level surface.
polarized outlet only one way. If the plug
4. Avoid overloading your circuit by not using other high
does not fit fully in the outlet, reverse the
wattage appliances in the same outlet. At 1500 watts,
plug. If it still does not fit, contact a
this unit draws 12.5 Amps.
qualified electrician to install the proper outlet.
NOTE: The power light will remain lit while heater is plugged
in.
Your heater is equipped with a technologically advanced
1Touch TM electronic thermostat. You can set the heater to
run continuously in manual mode or set the 1Touch
Thermostat to your desired temperature setting. The
1Touch TM thermostat will automatically turn the heater ON
or OFF depending on the preset comfort level. The
comfort level ranges between 60° and 80° Fahrenheit.
• Amps: 12.5
• Wattage: 1500W (+5% -10%)
• Working voltage: 120V AC/60Hz
In the U.S.A.
If you have any question regarding this warranty or would
like to obtain warranty service, please call 1-800-253-2764
and a convenient service center address will be provided
to you.
In Canada
If you have any question regarding this warranty or would
like to obtain warranty service, please call 1-800-253-2764
and a convenient service center address will be provided
to you.
In the U.S.A., this warranty is offered by Sunbeam
Products, Inc. doing business Jarden Consumer Solutions
located in Boca Raton, Florida 33431. In Canada, this war-
ranty is offered by Sunbeam Corporation (Canada) Limited
doing business as Jarden Consumer Solutions, located at
20 B Hereford Street, Brampton, Ontario L6Y 0M1. If you
have any other problem or claim in connection with this
product, please write our Consumer Service Department.
© 2008 Sunbeam Products, Inc. doing business as
Jarden Consumer Solutions. All Rights Reserved.
Distributed by Sunbeam Products, Inc. doing business as
Jarden Consumer Solutions, Boca Raton, Florida 33431.
BCH4830CN08EFM1 Printed in China
1. Plug the heater into a 120V AC electrical outlet.
2. To start the unit, push the Mode/Off button once for the
HIGH (HI) manual setting. (See Figure 1)
3. Press the button again for the LOW (LO) manual
setting. (See Figure 1)
4. To stop the unit, press and hold the button for two
seconds or keep pressing the button until all the
temperature indicators are OFF.
To take advantage of the 1Touch TM Thermostat continue
to press the Mode/Off button until the desired
temperature is set in either the HIGH or LOW setting.
When the ambient temperature rises above the set
temperature, the heater will stop. When the ambient
temperature drops below the set temperature, the heater
will turn on automatically.
NOTE: When the 1Touch TM thermostat is set, either the
HIGH (HI) or LOW (LO) power light, and the temperature
light will remain lit during operation. (See Figure 1)
NOTE: It is normal for the heater to cycle ON and OFF
as it maintains the preset temperature. To prevent the unit
from cycling, you need to raise the thermostat setting.
NOTE: 1Touch TM has memory. The 1Touch TM thermostat
will remember the previous temperature setting after the
unit has been turned off. However, if the unit is
unplugged, the 1Touch TM thermostat will be reset and will
no longer remember the previous temperature setting.
Figure 1
D
A. Mode/Off BUTTON
B. HIGH POWER
21
18 24
LIGHT
15 27
C. LOW POWER LIGHT
TM
D. SET TEMPERATURE
LIGHTS
C B
A
1. Select the desired control setting and press the
oscillation button once to turn oscillation on.
2. To stop oscillation press the oscillation button again.
3. Please do not manually turn the unit; it is designed to
turn only by motorized oscillation.
1. Always unplug the heater and allow to cool before
cleaning.
2. Clean the unit with a soft cloth moistened with a mild
soap solution. Please be cautious near the heating
elements.
Over time, dust may accumulate on the front grills.
This can be removed by wiping the unit with a damp
cloth. Always unplug unit and allow to cool prior to
cleaning.
3. NEVER use abrasive or flammable solvents to clean the
unit.
4. After cleaning, be sure to completely dry the unit with a
cloth or towel.
Store heater in a cool, dry location. Bionaire ®
recommends storing the unit in its original, or
appropriately sized box.
1. Every few weeks check the condition of the pre-filter.
2. Remove the inlet grill. If the foam pre-filter has collected
a noticeable amount of dust, remove it from the inlet of
the grill and wash it in warm soapy water. Rinse and
dry the pre-filter thoroughly before replacing it in the
inlet of the grill.