Related Manuals for Fieldpiece VP633EU
Summary of Contents for Fieldpiece VP633EU
- Page 1 Fieldpiece ® Vacuum Pump with RunQuick® Oil Change System OPERATOR'S MANUAL Models VP633EU, VP633UK, VP833EU, VP833UK, VPX33EU, VPX33UK...
-
Page 2: Table Of Contents
Contents Operation Important Notice RunQuick® Oil Change System Evacuation with a 4 Port Manifold Safety First! Evacuation with a 3 Port Manifold Direct Evacuation Safety Information Oil Change Procedure Vacuum Pump Protection Dynamic Vacuum Measurement Setup Remote Exhaust IEC Power Cord with Screw Locks Gas Ballast Valve Switch Grounding Instructions LED Indicators... -
Page 3: Important Notice
This vacuum pump is used for evacuating prevent injury or damage to you or equipment. (drying) refrigerant lines Fieldpiece’s recovery machine is available for recovering refrigerant WARNINGS – failure to heed these hazards and actions Read and understand this operator’s manual... - Page 4 Electrical shock risk - Do not operate in wet environments, rain, or levels as specified in Safety Data Sheet (SDS). Use a ventilation fan to around any liquids. maintain 6 air exchanges per hour within this zone. NOTICE: Risk of Property Damage. The use of an undersized extension WARNING: EXPLOSION HAZARD.
-
Page 5: Safety Information
Safety Information IEC Power Cord with Screw Locks For protection, the vacuum pump includes a screw lock for the Vacuum Pump Protection unit’s power cord. With the unit switched OFF ( O ), twist the wire lock upwards and Ensure clean oil is added to a level between MIN and MAX lines. plug the female end of the power cord into the unit. -
Page 6: Specifications
For Use With: A3, A2L, and A1 Refrigerants Not for Use With: R-702, R-717 Oil Capacity: 237ml (8 oz) Oil Compatibility: Fieldpiece Vacuum Pump Oil (Highly refined and optimized for proper sealing and lubrication) Oil Backlight: Blue LED Oil Drain: Ball Valve Port Sizes: (1) 1/4”, (2) 3/8”, (1) 1/2”... -
Page 7: Description
Good oil is the lifeblood of every evacuation - Change Oil Quickly, Even with the Pump Running Fieldpiece vacuum pumps have a huge, backlit window - Extra Oil Bottle Storage on the oil tank to let you clearly see the condition of the... -
Page 8: Tech Tips
6. Evacuate down to below 500 microns. pump is running. Always use fresh Fieldpiece Vacuum Pump Oil. If oil is left in the Warm the pump in your truck/home by letting it sit in a warm pump for more than a week, the oil may have absorbed enough environment. -
Page 9: Operation
Operation Gas Ballast Valve (Open) IEC Power Cord Inlet with Screw Lock Motor Power Switch ( OFF / O ) Power Cord Storage (VP633) Source Voltage Backlit Oil Window and Tank Access (4 Screws) Switch on Back LED Indicators 4 Input Ports Oil Tank Cap Power Cord Storage Wrap Remote Exhaust Collar... -
Page 10: Runquick® Oil Change System
RunQuick® Oil Change System Easy View Window and Oil Backlight There are a few signs that remind you to change your oil. The visual The only way to create a deep vacuum is to condition is one of them. If it looks old, change it. You will see tiny air evacuate with fresh oil, especially at the end of bubbles with fresh oil. -
Page 11: Evacuation With A 4 Port Manifold
Read Tech Tips (page 14) for optimum gauge placement and variations to reduce recovery times 1. Always fill with fresh Fieldpiece Vacuum Pump Oil (page 26). Running the pump without oil will damage the pump and void the warranty. Oil can be drained while the pump is running if refilled within 3 minutes (within 30 seconds to maintain your vacuum). -
Page 12: Evacuation With A 3 Port Manifold
Read Tech Tips (page 14) for optimum gauge placement and variations to reduce recovery times 1. Always fill with fresh Fieldpiece Vacuum Pump Oil (page 26). Running the pump without oil will damage the pump and void the 3 Port warranty. -
Page 13: Direct Evacuation
Read Tech Tips (page 14) for optimum gauge placement and variations to reduce recovery times 1. Always fill with fresh Fieldpiece Vacuum Pump Oil (page 26). Vacuum Running the pump without oil will damage the pump and void the Gauge Vapor warranty. -
Page 14: Oil Change Procedure
1. Ensure the drain valve is closed (horizontal). 2. Unscrew the pump’ s oil fill cap 1/4 turn counter clockwise. 3. Open a new 8 ounce bottle of Fieldpiece Vacuum Pump Oil (OIL8X3). Put the bottle cap on the side of the bottle (CAP STORAGE). -
Page 15: Gas Ballast Valve Switch
Gas Ballast Valve Switch LED Indicators Much of the air and moisture in a system are Three columns of LEDs in the oil window removed before reaching 3000 microns For wet indicate various states The blue lights of the systems, you should open the gas ballast during right column indicate power is connected The this initial pull down Doing so helps the pump blue lights of the middle column shine when the... -
Page 16: Maintenance
Maintenance Oil Window Cleaning It’s important to see the condition of your oil as well as General the LED indicators located in the oil reservoir The large oil drain ball valve will typically drain solids This machine is not intended for use by persons and sludge when changing the oil When it becomes hard (including children) with reduced physical, sensory or mental to see through the window, you can remove the oil window... -
Page 17: Troubleshooting
Oil in the pump may have become overly viscous due to Perform a triple evacuation to carry moisture out of the system by contamination or low temperature. Use fresh Fieldpiece Vacuum Pump purging the system with dry nitrogen. Oil within the pump’s operating temperature. -
Page 18: Limited Warranty
Fieldpiece shall not be liable for loss of use of the machine or other incidental or consequential damages, expenses, or economic loss, or for any... - Page 19 VP633 VP833 VPX33 Scan for your region. US, CA, MX EN, DE, FR, IT, ES, PT, NL, NO, SE, DK, FI Document: Opman VP633 VP833 VPX33 EU UK © Fieldpiece Instruments, Inc 2024; v12...
Need help?
Do you have a question about the VP633EU and is the answer not in the manual?
Questions and answers