Advertisement
Quick Links
Klinger & Born GmbH
Schalten mit System
In den Schlangenäckern 5
64395 Brensbach
Instruction manual
Softstarter S3 for 3Ph-400V
T + 49 (0) 6161 - 9309 - 0
F + 49 (0) 6161 - 9309 - 10
info@klibo.de
www.klibo.de
Geschäftsführer:
Dipl.-Wirt.-Ing. Peter Born
Volker Treusch
Sitz: 64395 Brensbach
Amtsgericht Darmstadt
HRB 70527
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Klinger Born Softstarter S3
Summary of Contents for Klinger Born Softstarter S3
- Page 1 Instruction manual Softstarter S3 for 3Ph-400V Klinger & Born GmbH T + 49 (0) 6161 - 9309 - 0 Geschäftsführer: Sitz: 64395 Brensbach Schalten mit System F + 49 (0) 6161 - 9309 - 10 Dipl.-Wirt.-Ing. Peter Born Amtsgericht Darmstadt In den Schlangenäckern 5...
- Page 2 Instruction manual Softstarter S3 Dear customer, Thank you for purchasing this product. The article has been finally tested and fulfils the requirements of the applicable European and national directives. We hereby confirm CE conformity, the corresponding declarations are on file with us as the manufacturer.
- Page 3 Instruction manual Softstarter S3 Handle the product with care. It can be damaged by knocks, blows or falling from a low height. Never use the product if it is moved from a cold to a warm room. The resulting condensation may destroy the product.
- Page 4 Instruction manual Softstarter S3 Special features • Gentle start-up with little impact on the electricity supply network • Jerk-free motor start protects material • Reduced start-up current • Integrated bypass contacts • Adjustable ramp-up time • Replaces classic star-delta starters •...
- Page 5 Instruction manual Softstarter S3 Block diagramm Mounting instructions There must be a minimum vertical clearance of 30 mm between the softstarter and the wall of the housing toprevent heat accumulation. Mount the softstarter on a 35 mm DIN rail. Slide the softstarter into the upper part of the rail and then apply light downward pressure until it snaps into place.
- Page 6 Instruction manual Softstarter S3 Connection The device must be connected by a qualified electrician and in compliance with the pertinent safety regulations. Connect as follows (see description on the bottom of this page too): Connection Explanation Motor connection U Supply network phase L1...
- Page 7 Instruction manual Softstarter S3 Commissioning and settings Once the softstarter has been properly connected it can be put into service. Control panel Setting Explanation potentiometer Ramp-up time (t) Setting range 3 ... 15 seconds (only version without current control) Please note that the start-up current increases considerably with very short ramp-up times.
- Page 8 Instruction manual Softstarter S3 LED status and Fault Indication LED status indication Explanation Remedy LED lights up red for about LED test when the softstarter is Indication of normal operation 100 ms switched on LED flashes red Fault indication: High...
- Page 9 Instruction manual Softstarter S3 Dimensional drawing Klinger & Born GmbH T + 49 (0) 6161 - 9309 - 0 Geschäftsführer: Sitz: 64395 Brensbach Seite 9 von 12 Schalten mit System F + 49 (0) 6161 - 9309 - 10 Dipl.-Wirt.-Ing. Peter Born Amtsgericht Darmstadt Stand: 05.02.2025...
- Page 10 Instruction manual Softstarter S3 Circuit diagram – connection example Klinger & Born GmbH T + 49 (0) 6161 - 9309 - 0 Geschäftsführer: Sitz: 64395 Brensbach Seite 10 von 12 Schalten mit System F + 49 (0) 6161 - 9309 - 10 Dipl.-Wirt.-Ing.
- Page 11 Instruction manual Softstarter S3 Safety information for soft starter S3 The user must observe all legal and technical regulations for the connection and operation of the device, such as the VDE regulations VDE0100, VDE0113 (EN60204), VDE0660 and many more. For safety and approval reasons (CE), unauthorised conversion and/or modification of the product is not permitted.
- Page 12 Instruction manual Softstarter S3 In case of questions consult our technical service: Klinger & Born GmbH In den Schlangenäckern 5 D-64395 Brensbach Tel. +49 (0) 6161 - 9309 - 0 E-Mail: info@klibo.de All company names and product designations in this document are trademarks of their respective owners.
Need help?
Do you have a question about the Softstarter S3 and is the answer not in the manual?
Questions and answers