Craftsman CMZPWSC100 Manual

CMZPWSC100 Surface Cleaner / Laveuse de surface / Limpiador de Superficie
Fig. A
6
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS

WARNING: When using this attachment, basic safety precautions should always be
followed including the following:
• Read all the instructions before using the product.
• To reduce the risk of injury, close supervision is necessary when a product is used
near children.
Know how to stop the product and bleed pressures quickly. Be thoroughly familiar
•
with the controls.
• Stay alert – watch what you are doing.
• Do not operate the product when fatigued or under the influence of alcohol or drugs.
• Keep operating area clear of all persons.
Do not overreach or stand on unstable support. Keep good footing and balance at
•
all times.
• Follow the maintenance instructions specified in the manual.
1 . For use with electric pressure washers only.
2 . Risk of explosion. Do not spray flammable liquids.
3 . Risk of injection or severe injury. Do not direct spray at people, pets, or electrical apparatus
and wiring.
4 . Gun kicks back – hold with both hands.
5 . Disconnect power source prior to the detaching of the high pressure hose.
6 . For cold water use only.
7 . For outdoor use only - store indoors.
SAVE THESE INSTRUCTIONS
Additional Safety Instructions
1 . Only use on flat horizontal surfaces.
2 . Never lift surface cleaner from the horizontal surface while in use.
3 . Keep hands and feet away from surface cleaner while in use.
4 . Never use surface cleaner with bare feet, wear appropriate foot wear.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal injury, turn unit off and disconnect
it from power source before making any adjustments or removing/installing
attachments or accessories. An accidental start-up can cause injury.
To Connect the Surface Cleaner (Fig. A)

WARNING: DO NOT attempt to change surface cleaner while pressure washer is running.
Turn pressure washer unit OFF before changing surface cleaner.
1. Shut OFF the pressure washer unit and turn OFF the water supply.
2. Pull the trigger 1 on spray handle 2 to relieve any water pressure.
3. To connect an surface cleaner 3 to the spray wand
toward the spray wand 4 and insert the surface cleaner 1/4" quick connector
4. Push the 1/4" quick connect collar forward so that the quick connect collar locks the surface
cleaner 1/4" quick connector in position.
6
3
3
4 , pull the 1/4" quick connect collar
6 .
4
5
Removing Surface Cleaner (Fig. A)
1. Shut OFF the pressure washer unit and turn OFF the water supply.
2. With the surface cleaner on the ground, pull the trigger
water pressure.
3. To disconnect the surface cleaner from the spray wand
collar 5 toward the spray wand
OPERATION

WARNING: To reduce the risk of serious personal injury, turn unit off and disconnect
it from power source before making any adjustments or removing/installing
attachments or accessories. An accidental start-up can cause injury.
Specifications
Connection
Maximum Pressure
Maximum Flow Rate
Maximum Water Temperature
Deck Width
Usage
1. Once the surface cleaner is installed, connect the hose to the pressure washer as described in
your pressure washer manual.
2. Start the pressure washer as described in your pressure washer manual.
3. Walk slowly behind the surface cleaner, cleaning as you go.
MAINTENANCE

WARNING: To reduce the risk of serious personal injury, turn unit off and disconnect
it from power source before making any adjustments or removing/installing
attachments or accessories. An accidental start-up can cause injury.
Spray Bar Nozzle (Fig. A)
If the nozzle becomes clogged with foreign materials, such as dirt, excessive pressure may
develop. If the nozzle becomes partially clogged or restricted, the pump pressure will pulsate.
Clean the nozzle immediately using the nozzle cleaner.
1. Shut OFF the pressure washer unit and turn OFF the water supply.
2. With the surface cleaner on the ground, pull the trigger
water pressure.
3. Remove the surface cleaner from the spray wand
toward the spray wand.
NOTE: Never point the spray bar nozzle openings at the face.
5
4. Using the spray tip cleaning tool, unclog any debris from the nozzles
5. Run water from a faucet or garden hose through the nozzle.
WARNING: To reduce the risk of injury, read the
instruction manual.
AVERTISSEMENT : afin de réduire le risque de blessures, lire
le mode d' e mploi de l' o util.
ADVERTENCIA: Para reducir el riesgo de lesiones, lea el
manual de instrucciones.
1
2
1 on spray handle
4 , pull the 1/4" quick connect
4 and pull the surface cleaner 3 forward to remove.
1/4" Quick connect
Up to 2,400 psi
Up to 1.2 gpm
140 °F (60 °C)
12"
1 on spray handle
4 by pulling the quick connect collar
7 .
7
7
2 to relieve any
2 to relieve any
5