Related Manuals for Taylor BC12
Summary of Contents for Taylor BC12
- Page 1 OPERATOR'S MANUAL Model BC12 Blender Original Operating Instructions 067802-M 7/24/09 (Original Publication) (Updated 12/3/14)
- Page 2 Complete this page for quick reference when service is required: Taylor Distributor: Address: Phone: Fax: E-mail: Service: Parts: Date of Installation: Information found on the data label: Model Number: Serial Number: Electrical Specs: Voltage Cycle Phase Maximum Fuse Size: Minimum Wire Ampacity: E 2009 Carrier Commercial Refrigeration, Inc.
-
Page 3: Table Of Contents
........Model BC12... - Page 4 Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in further civil and criminal penalties. All rights reserved. Taylor Company a division of Carrier Commercial Refrigeration, Inc. 750 N. Blackhawk Blvd. Rockton, IL 61072 Table of Contents Model BC12...
-
Page 5: To The Installer
Please contact your local authorities. insulation of the conductors from abrasion. If the supply cord is damaged, it must be replaced FOLLOW YOUR LOCAL ELECTRICAL CODES! by an authorized Taylor service technician in order to avoid a hazard. 140107 Model BC12... -
Page 6: To The Operator
Taylor Distributor. Note: Your Taylor warranty is valid only if the parts are authorized Taylor parts, purchased from the local authorized Taylor Distributor, and only if all required service work is provided by an authorized Taylor service technician. -
Page 7: Safety
DO NOT use a water jet to clean or rinse and its parts. Taylor has gone to extreme efforts to the unit. Failure to follow these instructions may provide built-in safety features to protect both you result in serious electrical shock. - Page 8 AVOID contact with the agitator shaft and DO NOT use attachments not recommended or sold by Taylor. Doing so may other moving parts. cause fire, electric shock, injury, or equipment Make sure the splash guard is installed prior damage.
- Page 9 Notes: Model BC12 Safety...
-
Page 10: Operator Parts Identification
Section 4 Operator Parts Identification BC12 Figure 1 110413 Operator Parts Identification Model BC12... - Page 11 BC12 Parts Identification ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO. SWITCH-ROD-SNAP ACTION 067650 FOOT A.-MIXER-PLUGGED 051500 SPRING-SWITCH ROD*BC12* 067648 GUARD-SPLASH*BC12* 067638 ROD A.-SWITCH*BC12* 067647 SWITCH-ROCKER-LIGHTED 067643-40 BRIDGE-RECTIFIER W/WIRES 067646 AGITATOR-CONE*BC10*BC12* 067549 ROD-SWITCH*BC12* 067649 AGITATOR-MIXER-PERM 051497 (GLOBE) (OPTIONAL) CAP-MIXER 051484...
-
Page 12: Important: To The Operator
Section 5 Important: To the Operator BC12 Figure 2 The BC12 blender is pre-programmed with one ITEM DESCRIPTION blending option and a pulse switch. PULSE/RINSE SWITCH POWER SWITCH PROGRAM DIAL RESET SWITCH POWER CORD PROGRAMMING PORT 091020 Important: To the Operator... -
Page 13: On/Off Power Switch
Press and hold the switch to automatically at the end of the program setting. activate the agitator. The agitator will stop as soon as the pulse switch is released. Figure 4 Figure 6 Model BC12 Important: To the Operator... -
Page 14: Program Dial
If an overload occurs, the reset mechanism will trip. To properly reset the unit, wait a short period of time to allow the motor to cool. Press the reset switch and resume operation. Figure 8 Important: To the Operator Model BC12... -
Page 15: Operating Procedures
Add “mix-in” ingredients such as liquid flavoring, cup. candy, cookies, fruit, or other condiments. Step 3 Place the power switch in the ON position. Figure 11 Figure 13 091020 Model BC12 Operating Procedures... - Page 16 Solid chunks are expected to be evident in the finished product. Step 9 Place the power switch in the OFF position when the machine is not in use. Figure 15 Figure 16 100921 Operating Procedures Model BC12...
-
Page 17: Pulse Switch Operation
Hold the cup under the agitator and lift up, so the agitator touches the bottom of the cup. Figure 20 Step 5 Before removing the cup, allow excess mixture to be thrown off the agitator and be caught by the cup or Figure 18 lid/collar. 091020 Model BC12 Operating Procedures... -
Page 18: Daily Cleaning
Daily Cleaning solution. Step 5 Wipe clean all stainless steel surfaces with an approved, non-abrasive commercial cleaner. This Taylor recommends daily cleaning and includes the mixer, dispenser, and organizer sanitizing. surfaces. Step 6 Clean sticky switches with a clean cloth, dampened with cleaning solution. -
Page 19: Sanitizing
Sanitizing Submerge the agitator in the cleaning solution, all the way to the bottom of the motor chamber. Place Taylor recommends daily cleaning and the power switch in the ON position. Allow the sanitizing. agitator to run for about 15 seconds. Repeat this step several times. -
Page 20: Limited Warranty On Equipment
Taylor, through an authorized Taylor distributor or service agency, will provide a new or re-manufactured part, at Taylor’s option, to replace the failed defective part at no charge for the part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited warranty for a Product failure. - Page 21 LEGAL REMEDIES The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or complaint with the Product, stating the defect or complaint and a specific request for repair, replacement, or other correction of the Product under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.
-
Page 22: Wiring Diagram
FILTER SUPPRESSOR PROGRAMMING PORT GROUND GROUND GROUND DC PM MOTOR 220V-240V 50/60 HZ PM - DC HALL EFFECT SENSOR - NON-CONTACT Model BC12 Wiring Diagram For Training Purposes Only 2009hz0528 PROGRAM INITIATE SELECTOR SWITCH SWITCH PULSE (SAFETY (SAFETY SWITCH (SAFETY...
Need help?
Do you have a question about the BC12 and is the answer not in the manual?
Questions and answers