Page 1
PADIN2 Video System Owner’ s and Installation Manual Features: -Audio in/out connectors -Full metal chassis -Two microphone input capability with individual gain controls -Internal and external paging capacity -Designed to “ trigger” monitors “ on” when VCP mode is selected Audiovox Specialized Applications 23319 Cooper Dr.
Wire Color Code and Function Bus Harness Layout Monitor Installation Diagram Exploded Monitor Installation View Speaker Connections Optional Video Cassette Mount VCP Rear Connections Troubleshooting Guide PADIN2 Wall or Console Installation PADIN2 and Monitor Electrical and Dimensional Specifications System Components PADIN2 Wiring Harnesses Microphone...
The PA should be mounted in a DIN sized opening on the vehicle’ s dash. This location will allow the driver access to controls. 6) MIC Installation a) MIC extension plugs into the back of the PADIN2 unit. b) MIC itself plugs into MIC extension cable. c) Adjust MIC gain controls to user preference.
Installation Guide (cont.) d) Depending on the angle of the luggage rack, a 10 wedge base may be required to keep monitors parallel to the floor. (Fig. 10) e) Drop four 5/16” grade 8 mounting bolts through mounting holes. (from top of luggage rack down) Place a mounting plate washer, lock washer, and nut on bolt and tighten to 100 In.lbs.
5) VCP- This button switches the PADIN2 to VCP and also triggers the monitor. Indicator light will be lit when this function is selected. 6) PA- This button switches the PADIN2 to the PA/MIC system. The indicator light will be lit when this function is chosen.
To adjust: a) Turn the PADIN2 to the “ on” position and turn the volume control to half volume and select Video or Radio on the source select control. b) Be sure the video or radio source is operational to obtain a reference level.
PADIN2 Harness Details IR LED: Clean the IR Receiver window on the front of the VCP, remove adhesive backing and apply IR LED to IR window on IR Harness the face of the VCP. Speaker Out Harness Power Monitor Trigger Out Harness...
Front Monitor Details Figure 6 1) Power Indicator- a) Will illuminate bright red when monitor is triggered “ on” by the PA system. b) Will illuminate dim red when monitor is triggered “ off” by the PA system.
Rear Monitor Features Video In (-) 12-24VDC Video Out (+) Video In (+) Video Out (-) Chassis Ground Trigger From PA 12V Figure 7 Monitor Operating Controls 1) Picture Selector- a) “ Press” left most button to trigger “ On screen display.” Order of control: Contrast, Brightness, Tint and Color.
Wire Color Code and Function Number Function Wire Color/ gauge PA- Video / Audio 18G Blue/White 12VDC Out Switching and 14G Red +12VDC Volume control 14G Black Chassis Gnd 18G Green Rt Speaker (+) 18G Green/Black Rt Speaker (–) 18G Gray Lt Speaker (+) 18G Gray/Black Lt Speaker (-)
Speaker Connections To obtain optimum sound pressure level, and compatible load, please use the speaker connection methods illustrated. 18 GRN(+) PASS. SIDE SPKR 18 GRN/BLK (-) 4 or 8 18 GRY (+) DRIVER SIDE SPKR 18 GRY/BLK(-) 18 GRN(+) PASS. SIDE SPKR 18 GRN/BLK (-) 4 Ohm only 18 GRY (+)
Rear VCP Connections Figure 13 1) Fuse- 2 Amp Fuse Used 2) Antenna In- External antenna hook-up 3) Video Out- To Monitor or Video 4) Audio Out- To Moinitor or Video 5) RF Out- Channel 3 or 4 output to Monitor 6) Channel Select- Selects setting for channel 3 or 4 selection, depends on area you live in.
Troubleshooting Symptom Cause Possible Solution PA will not power up No 12V power to the PA Check for front panel fuse. Check for 12V power to PA PA not turned on Monitors will not power up No 12-24V power to Check monitor 5-Amp fuse monitors Check for 12V to 24V power at...
PA Installation- Wall Mount Lower Left Side PADIN2 Of Driver's Seat DIN Sleeve (4) #8 Self-Tap Screws Wall Can Mounting Plate (Use DIN Sleeve) Wall Mount Box P/N 1400002 (4) #10 Self-Tap Screws ___________________________________________ PA Installation- Console Mount PADIN2 DIN Sleeve...
PA Electrical and Dimensional Specifications Electrical measurements: *Measurements made at Vcc=14.7VDC Maximum Output Power: 4 , Internal 11.8V (35 Watts) per channel Maximum Output Power: 4 , External 10.0V (25 Watts) Output Power before clipping: 4 , Internal 8.8V (19.4 Watts) per channel Output Power before clipping: 4 , External 7.5V (14.1 Watts) Output Power, THD 10%: 4 Internal...
Page 20
$14.00 Unlike household electronics, all of our products have been specifically designed and tested for the mobile environment and are only available through ASA. To order any of these products, please contact Audiovox Specialized Applications at www.entertainment-to-go.com or 800-688-3135. *Prices subject to change...