Related Manuals for Truper PRO PODI-40A
Summary of Contents for Truper PRO PODI-40A
- Page 1 Lawn mower 40 V 4 Ah Manual Applies for: Code Model 103245 PODI-40A PODI-40A Read this manual thoroughly CAUTION before using the tool.
-
Page 2: Table Of Contents
Contents CAUTION Technical data Power requirements To get the most out of the tool, extend its lifespan, claim the General safety warnings warranty if necessary, and avoid for electric tools serious risks or injuries, please read this manual thoroughly Safety warnings before using the tool. -
Page 3: Technical Data
The thermal insulation class of the motor windings: Class B WARNING If the power cable is damaged, it must be replaced by the manufacturer or a TRUPER Authorized Service Center to prevent any risk of electric shock or significant accidents. The electrical insulation of this tool is altered by splashes or spillage of liquids during its operation. -
Page 4: General Safety Warnings For Electric Tools
Use and care of the battery-powered tool. before connecting to the power source and/or the battery or Only recharge with the charger specified by TRUPER. transporting the tool. Using the charger specified for one battery with another battery can cause a Carrying power tools with your finger on the switch or connecting power tools fire hazard. -
Page 5: Safety Warnings
Batteries and charger • Avoid constantly stopping while operating the tool to DANGER • Use only TRUPER chargers to charge the prevent battery damage. tool's battery. Using another charger may cause a fire or • Do not throw batteries into the fire. The cell may risk of injury. - Page 6 Safety warnings for the use of lawn mowers Before using the lawnmower • Thoroughly inspect the area to be CAUTION WARNING • Establish a pruning pattern that avoids mowed to avoid any obstacles and remove foreign dumping waste material on the side of streets, sidewalks, objects that may be tripped over or thrown by the pedestrians, etc.
-
Page 7: Parts
Parts Soft grip handle On/Off lever switch Safety key Upper handle Locking lever Cable clip Lower handle Safety guard Handle lock lever Batteries protective cover Cutting height adjustment lever Wheel Grass bag Charger Batteries ENGLISH... -
Page 8: Assembly
Assembly Handle Installation. • Turn the locking lever (C1) of the platform counterclockwi- se to remove it. • Insert the lower handle into the platform slot (A) by passing the mounting bolt through the handle hole (B). • Place the locking plate (C1) with its washer on the mounting bolt and turn until the assembly is properly secured as indicated in (G). -
Page 9: Startup
Startup On and Off • Insert the safety key into the engine switch on the top of the main handle. • Slide the key in the indicated direction on key 1. Pull the switch lever towards handle 2 and the mower will start. -
Page 10: Battery Installation Or Removal
Startup Battery Installation or Removal To install the batteries: • Lift the protective cover of the battery compartment. • Insert each battery into the receptacle and push until you hear a click. • To remove the batteries: • Press the battery release button and pull to remove the batteries from the tool. -
Page 11: Operation
Operation Recommendations • Adjust the lawnmower to the desired cutting height. • Turn on the lawnmower on level ground. • When cutting thick grass, mow more slowly to achieve a • Push the lawnmower by the handle to cut the grass; better cut and proper clippings discharge. -
Page 12: Maintenance
Do not use plastic wrap to avoid moisture buildup. secure the blade to prevent involuntary movement. Blade Replacement • Use padded leather safety gloves from TRUPER. • Wedge a wooden block between the blade and the guard to prevent the blade from turning. -
Page 13: Troubleshooting
Rotate the blade 180 degrees and tighten it again. If the lawnmower still vibrates, take it to a TRUPER Authorized Service Center. The battery charger LED light •... -
Page 14: Warning Symbols
Troubleshooting Problem Solution Debris is observed during • Too much grass cut. Adjust the wheel cutting height to shorten the cut length. Do not shredding. cut more than 1/3 of the total length. • Check the sharpness of the blade. Always keep the blade sharp. Low or decreased runtime •... -
Page 15: Authorized Service Centers
Authorized service centers In the event of any problem contacting a Service Center, please see our webpage WWW.TRUPER.COM to get an updated list, or call our toll-free numbers 800 690-6990 or 800 018-7873 to get information about the nearest TRUPER Authorized Service Center. -
Page 16: Warranty Policy
It includes the costs of transportation of the product that derive from its fulfillment of its service network. Phone number 800-018-7873. Made in China. Imported by TRUPER, S.A. de C.V. Parque Industrial 1, Parque Industrial Jilotepec, Jilotepec, Edo. de Méx. C.P. 54257, Phone number 761 782 9100.
Need help?
Do you have a question about the PRO PODI-40A and is the answer not in the manual?
Questions and answers