Do you have a question about the RAYDENT Studio and is the answer not in the manual?
Questions and answers
Subscribe to Our Youtube Channel
Summary of Contents for ray RAYDENT Studio
Page 1
3D Printer (RAM600-M) User Manual RUG-9011-EN Rev. 2.0...
Page 2
This user manual contains information for appropriate use of RAYDENT Studio. The operator must read this manual carefully before using the product. The operator must follow instructions and safety regulations described in the user manual to prevent any injury to the operator and damage to the product.
Connect to PC ....................27 Software Installation ....................28 RAYDENT Studio Installation ................28 RAYDENT Studio Screen Composition ..............32 RAYDENT Studio Setting..................33 Add Printer by Connecting with Serial Port ............33 Add Printer by Adding Specific IP Address ............35...
Page 4
RAYDENT Studio Table of Contents Move the location of the added printer ............. 38 Disable Printer....................39 Remove Printer ....................40 Rename Printer ....................41 Change Printer IP .................... 43 Change Printer Setting ..................45 3.7.9.1 General setting ..................45 3.7.9.2...
Page 5
RAYDENT Studio Table of Contents Generate Support Stand (Manually) ..............90 Automatic Supports Generation............... 92 Remove Support ..................... 95 Supports Clearing ................... 96 Attaching Bars ....................98 Printout measurement ................... 100 Specifying Offset ................... 102 Auto Positioning .................... 106 Prepare Auto printing..................107 Save Project ....................
Page 6
RAYDENT Studio Table of Contents This page intentionally left blank.
Page 7
RAYDENT Studio 1 User Manual Introduction User Manual Introduction...
Related Terms Some terms used in this manual may be used interchangeably as follows. RAYDENT Studio is the same as 3D printing system, product, or program. 3D printer is the same as RAYDENT printer, printer, or main body. IPA is the same as Isopropyl alcohol or alcohol.
RAYDENT Studio 1 User Manual Introduction Safety Information The following safety information must be read and understood before using the product. Please check the safety precautions to use it safely and correctly. Improper use of the product may cause bodily injury or death.
RAYDENT Studio 1 User Manual Introduction Precautions for Installation / Remarques lors d'une installation du produit Risk of electric shock or fire Il y a un danger de commotion ou incendie. Do not install the product in humid or dusty place or Ne pas installer au lieu plein d’humidité...
Only use the resin provided by Ray Co., Ltd. Ne pas utiliser la résine que (S.A.)Ray n’a pas offert. Faites attention pour que la résine ne soit pas mise à Do not get the resin on your skin or in your eyes.
RAYDENT Studio 1 User Manual Introduction Precautions for Power Connection / Remarques lors d’une connexion électrique Risk of electric shock or fire Il y a un danger de commotion ou incendie. Do not use loose power outlets or damaged power Ne pas utiliser la prise relâchée ou le cordon...
RAYDENT Studio 1 User Manual Introduction Precautions for Cleaning the Product / Remarques lors d'un nettoyage du produit Risk of electric shock or fire Il y a un danger de commotion ou incendie. Remove the power cord when cleaning the Débrabchez le cordon d’alimentation lors d’un nettoyage...
Page 14
RAYDENT Studio 1 User Manual Introduction This page intentionally left blank.
Page 15
RAYDENT Studio 2 Product Introduction Product Introduction...
Actual components may look different from pictures above. Depending on the sales option or country, the type, quantity, and packaging of the components provided may look different from the contents of this manual. For inquiries regarding components, contact Ray Customer Service or sellers.
RAYDENT Studio 2 Product Introduction Sections and Functions Front Back Items Description Press the power button to switch the power on and off. The power status is indicated through LED light. LED off: 3D printer is turned off. Power Button White LED: 3D printer is in standby mode.
Page 18
RAYDENT Studio 2 Product Introduction Items Description A container containing 3D printing resin. ① Vat fixing knob Vat fixing knobs for tightening the vat. ② LCD protective Sheet to protect the LCD. ③ sheet...
RAYDENT Studio 3 Installation Installation Installation Environment Installation Setting The product should be installed on a flat floor within 1° and on a table capable of stably supporting a weight of 10 kg or more in an area of 50 cm x 50 cm or larger.
RAYDENT Studio 3 Installation Working Environment Do not install the product in a place exposed to direct sunlight or ultraviolet (UV) light. Use the product at room temperature between 23°C to 28°C (73.4°F to 82.4°F). Do not install near a wireless apparatus or mobile device that generates electromagnetic wave.
RAYDENT Studio 3 Installation Maintenance As described on the description, the user must conduct maintenance check periodically. The user has an obligation to manage the product in order to prevent potential problems. Check Cycle Description Check for damage in the product or parts.
RAYDENT Studio 3 Installation Product Installation Connect Power For initial installation, make sure that the mains power of the installation location matches the AC adapter specifications. Connect the power cord and AC adapter, as shown in the following figure. Please contact the seller if the product and the enclosed power cord are different from those in local area.
RAYDENT Studio 3 Installation Mount build plate and vat Push the build plate to the holder all the way in and then pull the tightening lever to fix it, as shown in the following figures. Mount vat LCD protective sheet Place the vat containing resin in the correct direction and securely tighten with the fixing knob.
Refer to "3.7 RAYDENT Studio Setting" about network setting. Network Setting Configuration RAYDENT Studio provides various network environments, as shown in the following figures. A computer ▶ A 3D printer (direct connection) Set a static IP address on your computer.
RAYDENT Studio 3 Installation Computers ▶ A 3D printer (multiple computer to one printer) Computers ▶ 3D printers (multiple computers to multiple printers) Check the connection of 3D printer network in RAYDENT Studio. Refer to "3.7 RAYDENT Studio Setting". Connect to PC After the printer is connected to a computer using a USB cable, name, IP and other information can be set.
RAYDENT Studio 3 Installation Software Installation The RAYDENT Studio and RAYDENT Designer software can be installed through the installation USB Memory provided in the box. RAYDENT Studio Installation RAYDENT Studio installation steps are as follow. Figure Description Install the RAYDENT Studio software by opening the installation file.
Page 29
Select the program to be installed and click [Next] button. Setting for installation has been completed. Press [Install] button to continue the installation process. Wait until the RAYDENT Studio installation has been completed. If you checked RAYDENT Desinger, as soon RAYDENT Studio...
Page 30
RAYDENT Studio 3 Installation After accept the license policy, click [Next] button. Select the path where RAYDENT Desinger will be installed and click [Next] button. Note: The system default is recommended as the default path. Select the path to create the shortcut icon and click [Next] button.
Page 31
RAYDENT Studio 3 Installation Please wait while RAYDENT Desinger is installed. Click [Finish] button to exit the installer. Click [Finish] button to close the setup page. RAYDENT Studio and RAYDENT Desinger icons are created on the desktop.
RAYDENT Studio 3 Installation RAYDENT Studio Screen Composition Category Description Initial setting option for RAYDENT Studio can be changed. Setting Printer unit and resin can be selected. Printer/Resin Object list will show. User can add or remove objects. Object User can adjust the output direstion of the selected object, and creat the supports.
RAYDENT Studio 3 Installation RAYDENT Studio Setting Add Printer by Connecting with Serial Port Figure Description Press [ ] button after running the program. A printer (connected to the computer serial port) setting page will appear after pressing ] button from the setup page.
Page 34
RAYDENT Studio 3 Installation After selecting the COM port that has been connected with printer, press ] button to see the information of current printer. After the printer is connected, name, IP, and other information can be edited. After pressing [ ] button, the change will be applied.
RAYDENT Studio 3 Installation If [ ] is displayed on the added printer, the application update of the printer is required. Refer to [3.7.9.5 Updating the printer] for how to update. Add Printer by Adding Specific IP Address Figure Description...
RAYDENT Studio 3 Installation Information about the printer can be verified in the printer list. If [ ] is displayed on the added printer, the application update of the printer is required. Refer to [3.7.9.5 Updating the printer] for how to update.
Page 37
RAYDENT Studio 3 Installation The software will sequentially access the networks connected to the computer in search for printers. Once the search is complete, the search window will disappear and the found printer will show in the list. If [...
RAYDENT Studio 3 Installation Move the location of the added printer Figure Description Can change the order of the printers added to the program. Press [ ] button after running the program. Select the printer you want to change the location of from the printer list.
RAYDENT Studio 3 Installation Disable Printer Figure Description Press [ ] button after running the program. Select the printer the user would like to change the setting from the printer list and press [ ] button to bring up the setting list.
RAYDENT Studio 3 Installation Remove Printer Figure Description Press [ ] button after running the program. Select the printer the user would like to change the setting from the printer list and press [ ] button to bring up the setting list.
RAYDENT Studio 3 Installation The user can verify the printer has been removed. Rename Printer Figure Description Press [ ] button after running the program. Select the printer the user would like to change the setting from the printer list and...
Page 42
RAYDENT Studio 3 Installation After renaming the printer, press [ button. The user can verify the printer has been renamed on the setting. The user can verify the printer has been renamed on the printer list.
RAYDENT Studio 3 Installation Change Printer IP Figure Description Press [ ] button after running the program. Select the printer the user would like to change the setting from the printer list and press [ ] button to bring up the setting list.
Page 44
RAYDENT Studio 3 Installation Input the desired IP address in the IP Change window and press [ ] button. A verification message will show to confirm the change. Press [ ] button to change the IP address. The user can verify the printer has been reconnected to the changed IP address on the printer list.
RAYDENT Studio 3 Installation Change Printer Setting 3.7.9.1 General setting Figure Description Press [ ] button after running the program. Select the printer the user would like to change the setting from the printer list and press [ ] button to bring up the setting list.
Page 46
RAYDENT Studio 3 Installation The user can enable/disable the Print Queue. It is disabled by default. The user is able to check whether FLEX Vat is securely locked. Note: Activate on FLEX Vat only.
RAYDENT Studio 3 Installation 3.7.9.2 Change resin settings Figure Description Press [ ] button after running the program. Select the printer the user would like to change the setting from the printer list and press [ ] button to bring up the setting list.
Page 48
RAYDENT Studio 3 Installation Press [ ] button on the left menu. You can change the curing time for each resin. Select the resin and output slice thickness you want to change. The curing time up to the slice thickness of the support base can be set according to the Print Zone.
Page 49
RAYDENT Studio 3 Installation After the support base, the curing time for the output plane can be set according to the Print Zone. Note: Changing the curing time can have a large effect on the printout. Only change it if you understand it correctly.
RAYDENT Studio 3 Installation 3.7.9.3 Running diagnosis Figure Description Press [ ] button after running the program. Select the printer the user would like to change the setting from the printer list and press [ ] button to bring up the setting list.
Page 51
RAYDENT Studio 3 Installation Press [ ] button on the left menu. The user can test for each function. Press ] button to start the test, and [ button to complete the test, and click the Test Result item to set the result.
Page 52
RAYDENT Studio 3 Installation When the measurement is completed, the position of the measured sensor and the final result are displayed. If the message shown on the left is displayed after measurement completed, proceed with the calibration using the “UV Calibration Kit. If the same...
Page 53
RAYDENT Studio 3 Installation Verify to see if the Standby LED turns whites properly to indicate the print job in Standby LED the print queue. Verify to see if the Printing LED turns white Printing LED properly to indicate printing operation.
Page 54
RAYDENT Studio 3 Installation Display the state of FLEX Vat fastened. [Locked]: Both sides are fastened. [Half Locked]: Only one side is fastened. Vat lock status [Unlocked]: Not fastened at least one side. [Unknown]: Not supported or sensor disabled. Display the internal temperature of the Temperature product.
RAYDENT Studio 3 Installation 3.7.9.4 Checking the statistics Figure Description Press [ ] button after running the program. Select the printer the user would like to change the setting from the printer list and press [ ] button to bring up the setting list.
Page 56
RAYDENT Studio 3 Installation Press [ ] button on the left menu. The user can check the statistical values such as reset date, usage time, build plate movement distance and print count. If you want to reset the items, you can reset them by press the [ ] button.
RAYDENT Studio 3 Installation 3.7.9.5 Updating the Printer Figure Description Press [ ] button after running the program. Select the printer the user would like to change the setting from the printer list and press [ ] button to bring up the setting list.
Page 58
RAYDENT Studio 3 Installation Press [ ] button on the left menu. Press [ ] button on the software or the firmware the user wants to update. If the user selects firmware from file dialog, the update will proceed. Do not disconnect the power cord while the update file is being transferred.
RAYDENT Studio 3 Installation 3.7.9.6 Managing Desinger licenses Figure Description Press [ ] button to access the priter configuration. Select the printer to change the setting from the printer list and press [ ] button to drop down the setting list.
Page 60
RAYDENT Studio 3 Installation Press [ ] button on the left menu. The valid Designer license is listed on the selected printer. If an additional Desinger license is needed, click the [ ] button on the bottom right to generate a Desinger license request file.
Page 61
RAYDENT Studio 3 Installation Click [ ] button to confirm the process. Verify the additional license has been added properly in the license list. The generated license file is dedicated to the requested printer only. It might display an error pop-up if applied on a different printer.
RAYDENT Studio 3 Installation An Warnting window for deleting licenses will appear and click [ ] button. Click [ ] button to close the pop up. Change Studio Setting 3.7.10.1 General setting Figure Description Press [ ] button after running the program.
Page 63
RAYDENT Studio\print_history folder. You can set the archving duration of these files in the Project archving duration item. The log files of RAYDENT Studio are saved in C:\Ray\log\RAYDENT Studio folder. You can set the archving duration of the log files in the Log archiving duration item.
RAYDENT Studio 3 Installation Press [ ] button to save the modified settings. Press [ ] button to reset to the factory settings. Press [ ] button to save the factory settings. If want to restore the previous value, press ] button.
Page 65
RAYDENT Studio 3 Installation Press [ ] button on the left menu. User can select the Printer model, Resin and Object type to chang the settings. Select Object type displays supported resins only. Adjust the initial number of intentionally over-cured slices to build a print to the Build plate.
Page 66
RAYDENT Studio 3 Installation The user is able to set the Cool time before turning UV on and after turning UV off. Press [ ] button to save the current settings. Press [ ] button to restore to the factory default.
RAYDENT Studio 3 Installation 3.7.10.3 User Preferences Proceed with “User Preferences” when detailed settings are required. Changing the “User Preferences” effects print quality, Only change it when you understand it clearly. Figure Description Press [ ] button after running the program.
Page 68
RAYDENT Studio 3 Installation User can turn on the anti-aliasing option to improve the surface quality of the printout. Depending on the option, the thickness of the printout may vary. Under Object Magnification, compensate for shrinkage during post- curing, you can set how much the object is to be magnified and printed for each resin.
RAYDENT Studio 3 Installation Press [ ] button to restore to the previous setting. 3.7.10.4 Curing Unit(RPC500) Setting Figure Description Press [ ] button after running the program. Turn the Curing Unit(RPC500) on and connect the device using the included USB cable.
Page 70
RAYDENT Studio 3 Installation When the device is connected successfully, you can update the firmware, check the current temperature of the curing unit and set the curing time according to the temperature range of each mode. If the connection fails, check the COM port number and reconnect the USB cable.
Page 71
RAYDENT Studio 3 Installation You can check the current temperature of the curing unit. Adjust the curing time and intensity according to the temperature range for the first mode of the curing unit. The mode is optimized for the RAYDENT C/B (Crown and Bridge) resin.
RAYDENT Studio 3 Installation Press [ ] button to restore to the facotry default. Press [ ] button to save the current setting. Press [ ] button to restore to the previous setting. 3.7.10.5 Reset Figure Description Press [ ] button after running the program.
Page 73
RAYDENT Studio 3 Installation Initialize all setting values related to the support. Note: The support setting values for all kinds of resins are changed to the factory default. Initialize all system output settings. Note: The setting values for all kinds of resins are changed to the factory default.
RAYDENT Studio 3 Installation 3.7.10.6 About Figure Description Press [ ] button after running the program. Press [ ] button on the left menu. You can check the product information and links to sites with product and service information.
Page 75
RAYDENT Studio 4 Operating the Software Operating the Software...
RAYDENT Studio 4 Operating the Software Operating the Software Import Object Open Figure Description On the screen menu, press [ button or press [Insert] key on the keyboard to open [Open File] window. Up to 20 objects can be selected. Press ] button to open the object.
RAYDENT Studio 4 Operating the Software Drag and Open Figure Description The user can drag up to 20 objects from a specific folder to the program. The selected object is added to the object list and can be seen from the screen (chamber).
RAYDENT Studio 4 Operating the Software Remove Object Remove All Objects Figure Description To remove all objects, press [ ] button. All objects will be removed from the chamber. Remove Individual Objects Figure Description Select the object the user wants to...
RAYDENT Studio 4 Operating the Software When [ ] button or [Delete] key is pressed, the selected objects will be removed. Duplicate Object Figure Description Select the object the user wants to duplicate. When [ ] button is pressed, the selected...
RAYDENT Studio 4 Operating the Software Switch to Object View Move the Screen Figure Description The user can move the screen up, down, and side-to-side when the left mouse button is pressed and held on the chamber. Rotate Screen Figure...
RAYDENT Studio 4 Operating the Software Top View Figure Description Press [ ] button from the menu to have a top view of the chamber. After, [ ] button will be changed to [ button.
RAYDENT Studio 4 Operating the Software Bottom view Figure Description Press [ ] button from the menu to have a bottom view of the chamber. After, [ ] button will be changed to [ button. Quarter view Figure Description Press [ ] button from the menu to have a top-right side view of the chamber.
RAYDENT Studio 4 Operating the Software Preparing Object Printing Change in Print Direction (Manually) Figure Description Select the object the user wants to change in the Object list. When the user presses [ button on the menu, sub-menu are shown.
Page 84
RAYDENT Studio 4 Operating the Software Putting a numeric value next to Orient X, Orient Y or Orient Z allows object rotation in corresponding axis and angle. Pressing the buttons on the right side rotates the object 90° at a time.
RAYDENT Studio 4 Operating the Software Change in Print Direction (Automatically) Figure Description User can be adjust the print direstion of individual objets or all objects. Select the object the user wants to change in the Object list. To adjust the print direction of individual objects, select the object the user wants to change.
Page 86
RAYDENT Studio 4 Operating the Software To adjust the print direction of all objects, press the [ ] button without selecting objects. The user can press [ ] button in the sub-menu to automatically adjust the object's print direction. If the user does not need to adjust the print...
RAYDENT Studio 4 Operating the Software Align the selected faces to the bottom Figure Description User can align the output direction of the object so that the selected face is at the bottom. Click the [ ] to display the submenu.
RAYDENT Studio 4 Operating the Software Make sure the selected face is aligned to the bottom. Print Direction Reset Figure Description Select the object the user wants to reset in the Object list. When the user presses [ button on the menu, sub-menus are shown.
Page 89
RAYDENT Studio 4 Operating the Software To reset the print direction of all objects, press the [ ] button without selecting objects. The user can press [ ] button in the sub-menu to reset the object's print orientation. If the user does not need to adjust the print...
RAYDENT Studio 4 Operating the Software Generate Support Stand (Manually) Figure Description Select the object the user wants to generate support in the Object list. When the user presses [ button on the menu, sub-menu will show. The area where the supports can be placed is displayed as a light green on the object.
Page 91
RAYDENT Studio 4 Operating the Software It is the appearance of Straight type generate support by created. It is the appearance of Brush type generate support by created. Can add a support to your printout without floating the build plate. The figure on the left shows an orthodontic support.
RAYDENT Studio 4 Operating the Software If the object has bars, a message will pop- up as the figure on the left. Press [ button to delete the bar and create a support. Automatic Supports Generation Figure Description Select the object the user wants to generate support in the Object list.
Page 93
RAYDENT Studio 4 Operating the Software If a user needs to print a hollow model or unevenly adhered model without supports , press [ button in order to create a base plate and increase the adhesion to the build plate.
Page 94
RAYDENT Studio 4 Operating the Software User can automatically generate supports for all abjects. Press the [ ] button without selecting objects. The user can press [ ] button in the sub-menu to automatically make the supports. When inserting/removing the supports is...
RAYDENT Studio 4 Operating the Software Remove Support Figure Description The user is selectively able to delete only the desired support from the currently created support. Select the object to be modified and press the [ ] button. Move the mouse cursor over the part...
RAYDENT Studio 4 Operating the Software When the user tries to erase the blue- support, a message will pop-up as the figure on the left. Press [ ] button to delete the suport. However, note that the supported area may...
Page 97
RAYDENT Studio 4 Operating the Software When inserting/removing the supports is completed, press [ ] button on the menu. User can clear the supports for all objects. If the user presses [ ] button on the menu, sub-menu will be shown.
RAYDENT Studio 4 Operating the Software Attaching Bars Figure Description Can create bars in your model. Select the model to create a bar. Press [ ] button in the menu to display the detailed menu. Can set the Bar width or Bar height.
Page 99
RAYDENT Studio 4 Operating the Software You cannot create a bar in a position higher than [Bar Height], and a red dot is displayed. If you want to create a bar up to the height of the model, adjust the Bar height value in the detail menu.
RAYDENT Studio 4 Operating the Software Printout measurement Figure Description A user is able to measure the thickness of the in/outside of the printout or the distance between two points. Select an object to print and click ] button to see more details.
Page 101
RAYDENT Studio 4 Operating the Software The thickness of the printout can be measured. The inside distance of the printout can be measured. The distance of the two specific points can be measured. The distance in the vertical direction of the selected surface can be measured.
RAYDENT Studio 4 Operating the Software After select the measurement type and direction, click the desired point. Then, the distance of the straight line, each axis will be calculated and displayed at the bottom of the submenu. Distnace: Between measureing two points.
Page 103
RAYDENT Studio 4 Operating the Software Load a model / surgical guide to apply Offset. Click [ ] button to view more detail operation options. (-) makes the printout thinner and the inner surface of the hole is wider in result.
Page 104
RAYDENT Studio 4 Operating the Software Select the offset mode with [Hole mode] or [Plain mode] depending on the shape of the part to be applied. After select the Offset value in the indicator click the surface to apply the adjustment.
Page 105
RAYDENT Studio 4 Operating the Software Offset can be applied not only specific surface but also on entire object if desired. Select the object to apply and select the Offset to apply. Click [ ] button to apply on entire object.
RAYDENT Studio 4 Operating the Software Auto Positioning Figure Description It provides a fully automatic preparation function to simplify the procedure for preparing printing. Press [ ] button on the menu to sequentially create the print direction and the supports for each object.
RAYDENT Studio 4 Operating the Software Prepare Auto printing Figure Description It provides a fully automatic preparation function to simplify the procedure for preparing printing. With no objects selected, press [ button on the menu to sequentially create the print direction and the supports for each object.
RAYDENT Studio 4 Operating the Software Save Project Figure Description The object in process can be saved as project file. When the user presses [ ] button from the menu, the latest saved folder will show. After naming the file, press [Enter] key or ] button to have the Scene saved in d3p extenstion file.
RAYDENT Studio 4 Operating the Software Import Project Figure Description Import the saved project file. On the screen menu, press [ button to display the final working folder. The RAYDENT Studion Project filename extension is d3p. After selecting the file, press [ ] button to open the project file.
Page 110
RAYDENT Studio 4 Operating the Software When the project file is loaded, if the printer to be output is selected, a message prompts you to print the project file directly. To output the project file, click the [ button. When you click the [...
RAYDENT Studio 4 Operating the Software Object Printing Printer and Resin Selection Figure Description When you are ready to print, select the Printer type the user wants to print from the Printer/Resin list to start printing. Select by referring to the printer name and model that are displayed in the list.
RAYDENT Studio 4 Operating the Software Slice thickness setting Figure Description After selecting the printer and resin type, you can set the thickness of the slice for each section in the slice bar on the right. Double-click left mouse button on any spot along the slice bar to add a marker for dividing sections.
RAYDENT Studio 4 Operating the Software If there are supports in the printout, the first section is for the support, slice thickness can be changed but position can not be moved. Start Printing Figure Description After finishing the slice thickness setting of...
Page 114
RAYDENT Studio 4 Operating the Software The information window is displayed on the screen before the printing. Confirm the information about printer name and resin type for the print job. After checking the information, a message indicating that the print has been started will pop up.
RAYDENT Studio 4 Operating the Software Pause and Resume Figure Description Select the item the user wants to pause in the print list. Pressing the [ ] button will display a warning message, and pressing the [ ] button to pause the printing.
RAYDENT Studio 4 Operating the Software If you pause output on a PC other than the PC from which you started the job, an error message appears. You can pause only on the PC from which you started the output.
RAYDENT Studio 4 Operating the Software Press [ ] button when the message indicating that the print has been stopped appears. If you stop output on a PC other than the PC from which you started the job, an error message appears.
RAYDENT Studio 4 Operating the Software Press [ ] button when a message indicating the start of print pops up. Cancel Printing Figure Description Select the item the user wants to cancel in the print list. A warning message will pop up if the user presses [ ] button.
RAYDENT Studio 5 Printing Printing Follow instructions in the followings to properly use the 3D printer. § Wear protective gloves. § Make sure the vat or LCD protective sheets is free of dust and moisture. § Use an air gun to remove foreign substances if the vat or LCD protective sheets is dirty.
RAYDENT Studio 5 Printing Preparing Resin Resin cartridges are classified for each application. Please select the proper resin cartridge for effective printing. It is necessary to check the type and capacity of the resin described in the resin pouch. Shake the resin pouch well.
Page 122
RAYDENT Studio 5 Printing Tilt both sides of the vat slightly so that the resin in the vat is evenly spread on the bottom. Store it in a place where light is blocked after putting the remaining vat and resin into packing of cartridge.
RAYDENT Studio 5 Printing Mounting vat Place the Vat containing resin in the correct direction and securely tighten with the fixing knob. LCD protective sheet Check for resin or residues on the bottom of Build Plate and vat and LCD protective sheet.
RAYDENT Studio 5 Printing Tighten the vat with the fixing knob. If the vat locking knob is not securely tightened on both sides, an error will occur and the print might not be acceptable. Be sure to tighten the vat fixing knobs.
RAYDENT Studio 5 Printing Taking Off the Printout Be sure to wear gloves before the operation. Make sure that the resin remains on the build plate and do not let it fall on the floor. Pay attention to the hand injuries because tweezers, nippers and scraper are sharp.
Page 126
RAYDENT Studio 5 Printing Use a tweezers to create a gap on the bottom of the printout by moving the tweezers up and down. Use a scraper to dislodge the printout. Pay attention to the hand injuries because tweezers, nippers and scraper are sharp.
RAYDENT Studio 5 Printing Removing Supports Do not hold the supports too tight. It could damage the printout. To keep the printout in a perfect form, remove the supports as close to the printout as possible. Hold the printout. Remove the supports in two steps.
RAYDENT Studio 5 Printing Cleaning the Printout Wear gloves and work. After removing the supports, use a neutral detergent to clean it under running water. (30 seconds ~) Do not use an ultrasonic cleaner for cleaning purpose. Use unit chair air gun to remove water and residue. If any water remains on the inside surface, wipe with a cotton swab.
For the best post curing result, please use the Curing Unit (Model number: RPC500) sold by RAY Co. For information regarding post curing, please contact the seller or Ray Co. customer service center.
RAYDENT Studio Appendix A. Product Specification Appendix A. Product Specification Items Specifications 50 ㎛ , 100 ㎛ Z-axis Layer Thickness XY Resolution 31.5 ㎛ Molding Size (X x Y x Z) 100 x 60 x 70 mm / 3.9 x 2.4 x 2.8 in.
RAYDENT Studio Appendix B. Troubleshooting Appendix B. Troubleshooting Symptom Cause Solution Power cord is not correctly Check if the power cord and AC adapter connnected. has been connected correctly. Unable to Turn on power. Did not press the power button for Press the power button for 3 seconds.
RAYDENT Studio Appendix C. Message Appendix C. Message Message Cause Solution Failed initialize Initialization of OpenGL driver Update the device driver of the graphic OpenGL. failed. card to the version. Update the latest graphic card driver. Please update the device driver of the...
Page 133
RAYDENT Studio Appendix C. Message Unable to check IP conflict Check the network cable connection to the on %1 It cannot check for conflicts printer, and check the network system Check the network cable because printer such as a router. If the same symptom is connection.
Page 134
RAYDENT Studio Appendix C. Message The user wants to disable the Wait for the completion of the requested Unable to make printer printer with the requested printing printing, or change the printer to disabled disabled while operating work on the PC.
Page 135
If the problems is not fixed, Unable to connect to the curing post curing machine restart the RAYDENT Studio and the unit through COM Port. through COM port curing unit and try. If the same symptom is repeated, please contact the seller.”...
Page 136
RAYDENT Studio Appendix C. Message Try after restarting the curing unit. If the Unable to update the curing unit. same symptom is repeated, please Firmware update failed. contact the seller. If the LED of the printer power button is blicking, the vat is not properly fastened.
RAYDENT Studio Appendix D. Regulations Appendix D. Regulations Product Disposal (Refer to wastes collection systems by countries) This symbol on the product, component to document, indicates that it should not be disposed of with other household wastes when disposing of the product. Please...
Need help?
Do you have a question about the RAYDENT Studio and is the answer not in the manual?
Questions and answers