SAFETY INSTRUCTIONS his manual explains the proper installation and use of your range hood, please read it carefully before using even if you are familiar with the product. The manual should be kept in a safe place for future reference. Never to do: o not try to use the range hood without the grease filters or if the filters ●...
Page 4
Always to do: mportant! Always switch off the electricity supply at the mains during ● installation and maintenance such aslight bulb replacement. he range hood must be installed in ccordance with the installation ● instructions and all measurements followed. ll installation work must be carried out by a competent person or qualified electrician. ●...
Page 5
Always to do: aution: The appliance and its accessible parts can become hot during operation. ● Be careful to avoid touching the heating elements. Children younger than 8 years old should stay away unless they are under permanent supervision. here is a fire risk if cleaning is not carried out in accordance with the instructions. ●...
WARNING 1. Before servicing or cleaning unit, unplug or disconnect the range hood from the power supply. 2. TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: A. Never leave surface units unattended at high settings. Boil overs cause smoking and greasy spillovers that may ignite.
WARNING TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. For the permanently-connected range hood TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.
CAUTION 1. To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages. 2. Take care when using cleaning agents or detergents. 3.
Page 11
2. The range hoods should be placed at a distance of 65-75cm from the cooking surface for best effect. See pic 1. 3. To install onto the wall, drill 4 holes of Ø 8mm on a suitable place according with the centre distance of hole in the back of the range hood.
9. Take out the baffle filter and cover plate from the accessory carton, and then install the two cover plates on both sides of the body. The installation method is as follows: a. Insert the pin of the cover plate into the lower part of the body, b.
Lay the expansion pipe on the outlet joints. Lift up the expansion pipe till it out of the wall through the hole on the wall. See pic 6 & 7. (Note: the expansion pipe is not including, need to purchase separately.) 4.
Page 14
Outdoor ventilation There are 2 methods for outdoor ventilation, including ' horizontal ventilation' and ' vertical ventilation'. The round outlet and rectangle outlet on the top of hood are for vertical ventilation. The outlet at the back of hood is for vertical ventilation .Please pay attention to the ventilation method when installation.
Start Using Your Cooker Hood Touch control with LED display Touch this button to turn on or off the range hood,and the fan will start and stop accordingly. Touch this button to set 1-3 speed. The LED display will indicate as 1-2-3-closed-1-2…circularly. Touch this button to turn on or off the light.
4.Long-press the speed button and light button on the range hood at the same time. 5.Click the device to enter the operation interface. Then you can start to control the hood. TROUBLESHOOTING Fault Possible Cause Solution Fan switch turned off Select a fan switch position.
NOTE: Any electrical repairs to this appliance must conform to your local, state and federal laws. Please contact the service centre if in any doubt before undertaking any of the above. Always disconnect the unit from the power source when opening the unit. MAINTENANCE AND CLEANING Caution: •...
GREASE MESH FILTERS The filters can be cleaned by hand. Soak them for about 3 minute in water with a mild detergent and then brush it gently with a soft brush. Do not apply too much pressure so as to avoid any damage to it . (Leave to dry naturally out of direct sun light) Filters should be washed separately to crockery and kitchen utensils.
Changing the light Remove the grease filter. Use a tool or the hand to press the spring splinter of both sides of LED light to the inside, until the light is pressed out. Then slightly pull the light connecting wire out, and dismantle the terminal of the light connecting wire.
Need help?
Do you have a question about the 6006B and is the answer not in the manual?
Questions and answers