Fireco Pneumatic Mast MULTIFUNCTIONAL PARTNER Use And Maintenance Instruction Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

FIRECO SRL

56, VIA E. FERMI

25064 GUSSAGO (BS) - ITALY

TEL. (+39) 030 37 33 916

FAX. (+39) 030 37 33 762

USE AND MAINTENANCE

INSTRUCTION MANUAL

Pneumatic Mast

MULTIFUNCTIONAL PARTNER/COMPACT

COMPACT

PARTNER

TRANSLATION OF THE ORIGINAL INSTRUCTIONS

Model/Serial Number:

Production year:

See ANNEX A

Table of Contents

Need help?

Do you have a question about the Pneumatic Mast MULTIFUNCTIONAL PARTNER and is the answer not in the manual?

Questions and answers

Summary of Contents for Fireco Pneumatic Mast MULTIFUNCTIONAL PARTNER

Page 1 FIRECO SRL 56, VIA E. FERMI 25064 GUSSAGO (BS) - ITALY TEL. (+39) 030 37 33 916 FAX. (+39) 030 37 33 762 USE AND MAINTENANCE INSTRUCTION MANUAL Pneumatic Mast MULTIFUNCTIONAL PARTNER/COMPACT COMPACT PARTNER TRANSLATION OF THE ORIGINAL INSTRUCTIONS Model/Serial Number:...
Page 2: Revision Matrix Of The Manual And Its Parts
WARNING THE OFFICIAL LANGUAGE CHOSEN BY THE MANUFACTURER IS ITALIAN. We are not liable for translations into other languages that do not conform to the original meaning. © FIRECO S.r.l. 2018...
Page 3: Table Of Contents
HAZARDOUS AREAS --------------------------------------------------------------------------------------------------------- 22 SIGNS ---------------------------------------------------------------------------------------------------------------------------- 22 SAFETY SYSTEMS ------------------------------------------------------------------------------------------------------------- 24 RESIDUAL RISKS--------------------------------------------------------------------------------------------------------------- 24 MACHINE DESCRIPTION ------------------------------------------------------------------------------------------------------ 28 PRINCIPLE OF OPERATION ------------------------------------------------------------------------------------------------- 28 MAIN COMPONENTS -------------------------------------------------------------------------------------------------------- 28 ENVIRONMENTAL CONDITIONS ------------------------------------------------------------------------------------------ 42 TECHNICAL DATA------------------------------------------------------------------------------------------------------------- 43 INSTALLATION ------------------------------------------------------------------------------------------------------------------- 44 © FIRECO S.r.l. 2018...
Page 4 SERVICE ------------------------------------------------------------------------------------------------------------------------- 88 SPARE PARTS ------------------------------------------------------------------------------------------------------------------ 88 ADDITIONAL INSTRUCTIONS ------------------------------------------------------------------------------------------------ 89 TAKING OUT OF SERVICE AND DISMANTLING ------------------------------------------------------------------------ 89 WASTE DISPOSAL ------------------------------------------------------------------------------------------------------------ 89 DRAWINGS AND DIAGRAMS ------------------------------------------------------------------------------------------------ 90 MACHINE DRAWINGS ------------------------------------------------------------------------------------------------------- 90 PNEUMATIC DIAGRAMS ---------------------------------------------------------------------------------------------------- 91 © FIRECO S.r.l. 2018...
Page 5 All contents of the documents and the information delivered by FIRECO S.r.l. along with the product which this manual refers to, are and shall remain exclusive property of FIRECO S.r.l., which will be the only and exclusive holder of intellectual property rights of the above mentioned.
Page 6: Foreword
Any reproduction of the whole or any parts of this manual or of its format, which does not comply with the purposes it was produced for, can only be done with the manufacturer’s previous consent. © FIRECO S.r.l. 2018...
Page 7: Who This Manual Is Intended For
The storing must be done handling this manual with care, with clean hands and avoiding dirty surfaces. Removing, tearing or arbitrarily changing any of its parts is strictly forbidden. The manual should be stored in an environment protected from humidity and heat and very close to the machine it relates to. © FIRECO S.r.l. 2018...
Page 8: Instruction Manual Update
Each figure is numbered progressively. The numbering works as follows: Example Figure 0.1.2 Figure    Progressive Chapter Paragraph number The progressive number starts from 1 in each new paragraph. TABLES NUMBERING Each table is numbered progressively. The numbering works as follows: © FIRECO S.r.l. 2018...
Page 9: Units Of Measurement
1 Hz = 1 s Force newton 1 N = 1 kg m s Pressure 1 bar = 100 kN m Work, energy, heat joule 1 J = 1 N m Power watt 1 W = 1 J s © FIRECO S.r.l. 2018...
Page 10: Definitions
RISK Combination of the probability and the degree of an injury or damage to health that can arise in a hazardous situation. GUARD Part of the machinery used specifically to provide protection by means of a physical barrier. © FIRECO S.r.l. 2018...
Page 11: Other Definitions
QUALIFICATION OF OPERATORS SYMBOL DESCRIPTION Generic unskilled worker level machine operator level machine operator Lifting and handling vehicle operator Mechanical maintainer Electric maintainer Technician of the manufacturer © FIRECO S.r.l. 2018...
Page 12: General Information
Each mast is identified by a CE mark and shows indelible reference data of the same (serial number). The brand is always placed on the main tube. For any communication with the manufacturer or service centers always quote these references. © FIRECO S.r.l. 2018...
Page 13: Declarations
The machine is realised in accordance with the relevant Community Directives that are applicable at the time of its placing on the market. The Declaration of Conformity is included in the present manual as ANNEX B. © FIRECO S.r.l. 2018...
Page 14: Safety Standards
Directive 2006/42/EC and of applicable Directives EC/EU. Place, date The manufacturer Gussago, 22/04/2021 FIRECO Srl - Legal Representative Christian Baribbi SAFETY STANDARDS The machine has been built in accordance with the technical standards listed below. STANDARD...
Page 15: Information On Technical Assistance
PARTNER/COMPACT MULTIFUNCTIONAL Pneumatic Mast INFORMATION ON TECHNICAL ASSISTANCE FIRECO S.r.l. provides, together with the product, a Certificate of Warranty that shall be valid for 24 months from the date of dispatch, as specified in the general conditions of sale. Figure 1 shows a sample of the certificate that is in the packaging.
Page 16: Warranty Information
 by FIRECO S.r.l. if the product has been subjected to repair or replacement under warranty. The transport costs for the return of the product from FIRECO S.r.l. to the Client are borne by  the Customer if the product has been subjected to repair or replacement outside of its warranty.
Page 17: Arrangements At The Customer's Expense
 improper use.  Such behaviors shall nullify every warranty obligation at the expense of FIRECO S.r.l. ARRANGEMENTS AT THE CUSTOMER’S EXPENSE Except for different contractual arrangements, the Customer will have to take care of: the arrangements for the installation, including supports and any required channeling;...
Page 18: Safety
 failure to comply with all or part of the instructions;  use contrary to national specifications;  disasters and exceptional events.  © FIRECO S.r.l. 2018...
Page 19: General Safety Instructions
However, the user can integrate the information supplied by the manufacturer with additional working instructions in order to contribute to the safe use of the machine, as long as these instructions are obviously not in contrast with what is reported in this Instruction Manual. © FIRECO S.r.l. 2018...
Page 20: Intended Use
Contact the manufacturer for the necessary verifications and authorisations. WARNING In the event of snow, the total weight supported by the mast may increase significantly. © FIRECO S.r.l. 2018...
Page 21 The verification of the product’s limits of use must be carried out by the user, by applying the data reported in this manual and with reference to the table set out in ANNEX A of this manual, which can be found at the end of the same. © FIRECO S.r.l. 2018...
Page 22: Contraindications For Use
 serious accidents; using the machine with hasty behaviour resulting from pressure to keep the machine running  in all circumstances. This behaviour can create potentially non-compliant working conditions. © FIRECO S.r.l. 2018...
Page 23: Operator's Seat
The surfaces on which the pictograms are applied must be clean, smooth and free from grease, oils or chemical products which reduce the adherence. © FIRECO S.r.l. 2018...
Page 24 Electric shock danger due to contact or proximity of the end of the mast to high or medium voltage lines PROHIBITION PICTOGRAMS SYMBOL DESCRIPTION Generic Prohibition Prohibition to remove the guards and protection and safety devices Prohibition to operate on moving elements Prohibition of access to unauthorised personnel © FIRECO S.r.l. 2018...
Page 25: Safety Systems
To ensure the safe use of the mast with respect to the overturning hazard,  please follow the instructions provided by the manufacturer in this document;  limit access to the area surrounding the mast. © FIRECO S.r.l. 2018...
Page 26 To ensure the safe use of the mast with respect to the limb crushing hazard,  be constantly present during the machine use, yet remaining at a suitable distance.  do not carry out any kind of work on the mast while it is moving. © FIRECO S.r.l. 2018...
Page 27 Measures have been taken (insulation, roofing, etc.) in order to protect the operator/maintainer from direct contact. It is forbidden to remove or tamper with the security systems. It is mandatory to verify the security systems efficiency periodically. Some pictographs can be found on the machine. © FIRECO S.r.l. 2018...
Page 28 The acoustic signal must be operated even when you notice people on the handling trajectory. In case the people start moving around, stop every maneuver. © FIRECO S.r.l. 2018...
Page 29: Machine Description
MAIN COMPONENTS The MULTIFUNCTIONAL TELESCOPIC MAST is made with components that are guaranteed by the Quality Control activities carried out by FIRECO Srl. The MULTIFUNCTIONAL pneumatic telescopic masts provide the solutions and the equipment described in the following paragraphs.
Page 30 On the upper part of the tube are holes for the fixing of the guide rings (PARTNER model) or head runners (COMPACT). For the COMPACT mast, another set of holes is present for the fixing of the end stops. © FIRECO S.r.l. 2018...
Page 31 Table 3-2.2: Classification of MULTIFUNCTIONAL masts. With the only exception of the top section or 1 mobile tube, all the mast tubes have a hole in their upper part to allow the outflow of rainwater when the mast is extended. © FIRECO S.r.l. 2018...
Page 32 The runners are supported by shim bands (able to make up for any internal play) and are 90° offset from one another. Shim bands Sliding runners Figure 3-2.5: Anti-rotation – COMPACT Model © FIRECO S.r.l. 2018...
Page 33 Stop tubes are fixed to the upper part of the mast, inside the gaps between the various tubes. When the mobile section is fully extended, the stop tube is compressed between the mobile section piston and the corresponding external guiding ring. © FIRECO S.r.l. 2018...
Page 34 Guiding ring Part of the last mobile tube inserted in the lower section Stop tube of the last mobile tube Main tube Piston Figure 3-2.9: Stop tubes with the mast being extended - PARTNER model © FIRECO S.r.l. 2018...
Page 35 Anti-rotation system Anti-rotation system Mobile tube top end Upper stop tube Upper stop tube Piston Figure 3-2.11: Upper stop tube with the mast being extended - COMPACT model © FIRECO S.r.l. 2018...
Page 36 You may want to install an extra drain tube (optional) so as for the rainwater stagnating inside the mast to be funneled and redirected to the desired destination. This option may be useful if the case the mast is installed inside a vehicle. © FIRECO S.r.l. 2018...
Page 37 In this way, you can let out all the water potentially present in the stop tube area. Stop tube of the last mobile tube Rain water drain hole on the main tube Figure 3-2.14: Rain water drain hole on the main tube - CLOSED mast © FIRECO S.r.l. 2018...
Page 38 A wedge device (C) acts as an anti-rotating device for the equipment at the top. Figure 3-2.16: Head with holes Please refer to paragraph 3-5 for further details on the installation of the equipment onto the top of the mast. © FIRECO S.r.l. 2018...
Page 39 The lamp units operate at 12V, 24V or 220V and each of their sets can have one or more floodlights. Fixing pins Floodlight Floodlight Central body Figure 3-2.17: Example of TT SPARK multifunctional tilt and turn unit © FIRECO S.r.l. 2018...
Page 40 (D1) and a ½” Gas threaded external one (D2), for the passage of the electric wire inside the mast and for the fixing of the base terminal board. Figure 3-2.19: Mast with non-rotating base © FIRECO S.r.l. 2018...
Page 41 The solenoid valve set, if present, is placed at the bottom of the mast and controls the extension/retraction of the mast in conjunction with the control system. Figure 3-2.21: Solenoid valve set at the mast base © FIRECO S.r.l. 2018...
Page 42 (provided by the end user)  Electric compressors combined with the MULTIFUNCTIONAL mast can be of two types: with an accumulator tank (left below)  without accumulator tank (right).  © FIRECO S.r.l. 2018...
Page 43: Environmental Conditions
NOTE: Some electric compressors or multifunctional tilt and turn units may require different environmental conditions. Check with FIRECO Srl the ideal operating conditions for the mast purchased. WARNING It is prohibited to use the machine in explosive/corrosive/extremely dusty environments or locations at risk of fire.
Page 44: Technical Data
The technical characteristics are shown in ANNEX A in the appendix of this manual. WARNING Since the characteristics may vary for each mast model, it is necessary to verify the correspondence of the serial number found on the mast with the one reported on the manual. © FIRECO S.r.l. 2018...
Page 45: Installation
WARNING FIRECO S.r.l. does not account for failures or any malfunction of the product resulting from poor transport conditions that do not comply with the guidance provided in this paragraph.
Page 46 PARTNER/COMPACT MULTIFUNCTIONAL Pneumatic Mast WARNING FIRECO S.r.l. is not liable for any damage caused to persons, animals and goods for the use of lifting systems different from those indicated. Make sure you have fully understood the indications in this paragraph.
Page 47 Handling of the mast set, with the main body of the pre-mounted multifunctional tilt and turn unit Lift the set by means of an overhead or jib crane with adequate capacity or by a forklift equipped with two forks. © FIRECO S.r.l. 2018...
Page 48 Lift the load, preferably from two sides, as shown in Figure 4-1.1. Figure 4-1.1: Grip points of the mast – horizontal For the vertical lifting, refer to Figure 4-1.2: Attach the straps or the lifting means under the fixed collar. © FIRECO S.r.l. 2018...
Page 49 Depending on the lamp units model, support the load on one or two areas, as shown in the examples in Figure 4-1.3. Always check the weight balance of the lamp units, so as to prevent unexpected movement or the fall of the load. Figure 4-1.3: Main multifunctional head grip points. Compressor handling © FIRECO S.r.l. 2018...
Page 50: Storage
It is up to the end user to possibly implement and make use of such a device at the electric supply source. The machine power supply must come from a line protected against overcurrent and against possible insulation faults. © FIRECO S.r.l. 2018...
Page 51: Placing
Please see paragraph 2-2 for further details. WARNING During the mast extension operations, contact with electrical wires and/or suspended structures might be possible, with consequent danger for the operators. © FIRECO S.r.l. 2018...
Page 52 Check thoroughly for the possible presence of power lines and/or suspended structures around the mast installation area. DO NOT INSTALL THE MAST DIRECTLY BELOW THE POWER LINES, EVEN IF THEY SEEM TOO HIGH TO BE REACHED BY THE MAST. © FIRECO S.r.l. 2018...
Page 53: Mounting
Supports for the fixing of the mast;  FIRECO S.r.l does not provide washers, screws and bolts for the fixing of the mast. WARNING The assembly and installation operations of the product shall be the customer's responsibility, who will take care of these activities, through the use of qualified and adequately trained technical personnel.
Page 55 Fix the base flange of the mast to the lower fixing device by using screws. As for the number and the size of the screws, please refer to the attached drawings. © FIRECO S.r.l. 2018...
Page 56 V-ring WARNING! On the main tube of the mast, near the guide ring, there is a 1/8” Gas threaded hole for the discharge of rainwater. Be careful not to block the hole with the wall collar. © FIRECO S.r.l. 2018...
Page 57 V-ring WARNING! On the main tube of the mast, near the guide ring, there is a 1/8” Gas threaded hole for the discharge of rainwater. Be careful not to block the hole with the roof collar. © FIRECO S.r.l. 2018...
Page 58 Figure 4-5.3: Fixing pins – TT SPARK Each floodlight set, coupled with a TT SPARK multifunctional tilt and turn unit, has a fixing bar with a quick coupling. Figure 4-5.4: Fixing bar with quick coupling – TT SPARK floodlight set © FIRECO S.r.l. 2018...
Page 59 The number of quick connectors may vary depending on the characteristics of the floodlight sets. Figure 4-5.7: TT SPARK floodlight sets electrical connection © FIRECO S.r.l. 2018...
Page 60 Direct the floodlight set as needed. For the TT HEAVY multifunctional tilt and turn unit, the floodlight set’s orientation can be changed by steps of 60°. Figure 4-5.10: Some possible orientations of the TT HEAVY lamp units © FIRECO S.r.l. 2018...
Page 61 The number of connection cables may vary depending on the characteristics of the floodlight sets. Figure 4-5.12: TT HEAVY lamp units electrical connection © FIRECO S.r.l. 2018...
Page 62 Connect the 90° quick fitting provided by FIRECO to the threaded hole on the main tube of the mast. NOTE: If you do not use the FIRECO quick fitting, please use a threaded fitting that does not exceed 4 mm. Insert the Rilsan tube into the 90° quick fitting.
Page 63: Connections To The Energy Sources
Pneumatic energy source (other than a compressor) Pneumatic connection Solenoid valve group Terminal box at the bottom of the mast For further details, please refer to the compressor use and maintenance manual, which is provided as an attachment to this manual, © FIRECO S.r.l. 2018...
Page 64 ø8 Rilsan tubes (not supplied). Figure 4-6.1: Super quick coupling for ø8 Rilsan tubes (not supplied). WITH ELECTRIC COMPRESSOR WITH ACCUMULATOR TANK Mast top equipment Mast Multifunctional control Compressor with an accumulator tank © FIRECO S.r.l. 2018...
Page 65 Connect the grounding wire to one of the fixing screws of the mast base bottom. The other end should be connected to the vehicle chassis or to another grounding point, as per end user’s arrangement. Figure 4-6.2: Grounding © FIRECO S.r.l. 2018...
Page 66: Preliminary Checks / Commissioning
 materials are hindering normal operation. verify the free movement and free rotation of all the moving parts.  Please refer to chapter 5 for more details on using the machine. © FIRECO S.r.l. 2018...
Page 67: Use Of The Machine
WARNING When the mast is being extended or retracted, do not move or start the vehicle on which it is installed. The vehicle must be still and blocked (hand brake up). © FIRECO S.r.l. 2018...
Page 68 Verify that all the pneumatic connections are active and in good working order. The pressure delivered by the pneumatic energy source must not exceed 2.5 bar. If you detect a value different from 2.5 bar, please contact FIRECO Srl: there may be failures or malfunctions in the pneumatic mast.
Page 69: Control System
Some multifunctional controls have a backlit keyboard, so as to ensure controls’ readability in low light conditions. The backlight automatically turns off after 10 seconds of inactivity. © FIRECO S.r.l. 2018...
Page 70 Command for the mast retraction (closing) Hold-to-run control Command for tilting the lamps of a lamp unit up and down 14 and 15 Hold-to-run control Sensor for lighting conditions in the surroundings Figure 5-2.2: Generic multifunctional control keys description © FIRECO S.r.l. 2018...
Page 71 On the SMART multifunctional control, battery charging occurs automatically when the control is connected to the power cable. To maximize the control life, it is recommended to keep it connected to the power cable when not in use. © FIRECO S.r.l. 2018...
Page 72 To securely open the discharge/drain valve, pull the ring outwards and, at the same time, loosen the valve head counterclockwise. To securely close the discharge/drain valve, pull the ring outwards and, at the same time, tighten the valve head clockwise. A spring will set the valve back into place. © FIRECO S.r.l. 2018...
Page 73: Use Procedures
Pull the discharge valve slowly to start the air discharge and therefore the retraction of the  sections. The closing speed can be adjusted by pulling the discharge valve further or closer outwards.  Avoid locking the valve in its open position to better manage the closing speed.  © FIRECO S.r.l. 2018...
Page 74: Diagnostics And Troubleshooting
Please consult the manufacturer for defects and/or malfunctions of the machine that are not described in this manual or that remain unresolved even after its consultation. © FIRECO S.r.l. 2018...
Page 75 To have access to the electronic board of the TT unit it is necessary to unscrew and remove the cover of the unit (pos. A in the figure below). After that the electronic board is directly accessible. Electronic board inside the TT unit Figure 5-4.1: Accessing the electronic board of the equipment on top © FIRECO S.r.l. 2018...
Page 76 • If this LED should not light up when any button on the Switched on transmission of remote control is pushed, please check the power supply on continuously commands, whenever the connecting plug and/or check if the internal battery is one of the command connected. buttons is pushed. © FIRECO S.r.l. 2018...
Page 77 • If pressing a key won’t turn the LED on, check the power keys on the connector and/or check if the internal battery is connected Fig. 5-4.3: SMART Multifunction Control – RF Transmission Led © FIRECO S.r.l. 2018...
Page 78 • Disconnect the power cord and check that the internal LIGHT battery. battery is connected • Disconnect the power cord, disconnect the battery for a few seconds, reconnect it and try reconnecting the cable • Damaged battery. It needs replacing. © FIRECO S.r.l. 2018...
Page 79 Check that the air inlet/outlet valve is working and connected properly. Obstacles or entangled cables which Interrupt immediately any movement of the mast. impede the normal functioning. Remove the obstacles or fix the cable entanglement issue. If the problem persists, contact Fireco Srl. © FIRECO S.r.l. 2018...
Page 80 Before replacing, check the dedicated paragraph. tional control 12. Air leak in the mast Contact the manufacturer for an extraordinary maintenance operation. 13. Fault/malfunction of the electronic Before replacing, check the dedicated paragraph. board 14. General electrical failure See dedicated paragraph. © FIRECO S.r.l. 2018...
Page 81 Hold down the extension green button (ID 1 in Figure 5-2.2) for at least 7 seconds, not  necessarily uninterruptedly (the duration may vary depending on the customer’s customizations agreed upon at the time of ordering). In fact, during this time any electrical movement is locked for safety reasons. © FIRECO S.r.l. 2018...
Page 82 The floodlights are switched off by sets.  The lamp unit will return to the zero position. One motor at a time is expected to start  according to the following sequence: © FIRECO S.r.l. 2018...
Page 83 The problem could be caused by the setting of the zero position of the end stop microswitches  coupled with the actuators in the TT unit. Please contact Fireco Srl for an extraordinary maintenance intervention. © FIRECO S.r.l. 2018...
Page 84: Maintenance
1-1. Any extraordinary maintenance operation performed by the customer, or by personnel that has not been authorised by FIRECO S.r.l., will result in the immediate revocation of any form of warranty. Always use the appropriate P.P.E. - Personal Protective Equipment: gloves;...
Page 85: Special Precautions
(Canada), depending on the country of installation. WARNING The solvents used to clean the various parts of the product may be potentially harmful and flammable. Make sure that the staff knows and follows the safety recommendations provided by the solvent manufacturer. WARNING © FIRECO S.r.l. 2018...
Page 86: Insulation From Sources Of Energy And Dissipation Of Residual Energies
At the end of the machine’s useful life, it must be thoroughly overhauled and inspected in order to verify the wear and general operation state. The inspection and verification activities must be carried out by the technicians entrusted by the manufacturer. © FIRECO S.r.l. 2018...
Page 87: Scheduled Routine Maintenance
Check the integrity of the power supply circuits Before each use and every six months and control devices Tab. 6-6.1: Scheduled Maintenance Table WARNING Failure to comply with what is required will relieve the manufacturer of any liability with respect to the warranty. © FIRECO S.r.l. 2018...
Page 88 NOTE: Do not resort to the automatic deactivation, rather use the dedicated hold-to-run command (ID 2 in Figure 5-2.2). Proceed likewise gradually cleaning all the sections until the complete closing of the mast. © FIRECO S.r.l. 2018...
Page 89: Extraordinary Maintenance
 Continuity of ground circuit.  Contact Fireco S.r.l. if you find that one or more components are damaged or in case of abnormal situations. EXTRAORDINARY MAINTENANCE Since the extraordinary maintenance operation is necessary when a fault occurs, you cannot predict the timings or the frequency.
Page 90: Accessories And Spare Parts
ALWAYS USE ORIGINAL SPARE PARTS. FOR ANY SPARE PART, PLEASE CONTACT THE MANUFACTURER. All spare parts must be original parts provided by FIRECO S.r.l. All defective parts must be replaced with products having the same code. We do not recommend the use of non-original parts: contrary cases will nullify the warranty conditions (if still existing) and the manufacturer will no longer be responsible for the machine use and for any damage to people and/or things.
Page 91: Additional Instructions
The product shown in this manual is composed of various elements made of different materials: Aluminum  Steel  Copper  Plastic  Even the packaging of the product itself may be composed of different materials: Cardboard  Wood  Plastic  © FIRECO S.r.l. 2018...
Page 92: Drawings And Diagrams
PARTNER/COMPACT MULTIFUNCTIONAL Pneumatic Mast 9 DRAWINGS AND DIAGRAMS MACHINE DRAWINGS © FIRECO S.r.l. 2018...

This manual is also suitable for:

Pneumatic mast multifunctional compact

Fireco Pneumatic Mast MULTIFUNCTIONAL PARTNER Use And Maintenance Instruction Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Fireco Pneumatic Mast MULTIFUNCTIONAL PARTNER

This manual is also suitable for:

Table of Contents