1. Manuals
  2. Brands
  3. Lumberjack Manuals
  4. Lathe
  5. SM8000
  6. Original instruction

Lumberjack SM8000 Original Instruction

Spindle moulder
Hide thumbs

Advertisement

Table of Contents

SAFETY AND OPERATING MANUAL
Spindle Moulder
S M8000
ORIGINAL INSTRUCTION

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SM8000 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Lumberjack SM8000

  • Page 1 SAFETY AND OPERATING MANUAL Spindle Moulder S M8000 ORIGINAL INSTRUCTION...

  • Page 2: Use Of The Machine

    Use of the Machine Purpose This machine is designed for moulding along and across the grain of prepared timber, using cutters and limiters. Operator Qualifications/Training Operators of this machine should have a suitable qualification in the use of woodworking machinery, including spindle moulders or should have been trained by someone holding such qualifications.

  • Page 3: Specification

    Specification Motor: 230/400,50Hz,1500W Table size: 600X400mm Roller table: 400x250mm Working height : 860mm Spindle diameter 30mm Height adjustment of spindle: 105mm Max. tool diameter: 150mm Table opening: 170mm Spindle speed: 1400/4000/6000/8000rpm GETTING TO KNOW YOUR MACHINE 1.Aluminium fence 2. Protective cover 3.
  • Page 4 Unpacking Main machine is packed in a plywood case. Cut the strapping and lift the lid of the crate from the base. Remove the loose items surrounding the machine and those stored in the base of the machine. These can be accessed through the opening door situated on the left hand side of the machine.
  • Page 5 Remove one of the stop screws from the sliding carriage rail. Before fitting the sliding carriage it should be noted that the two outboard bearing wheels are mounted on eccentrics. Should ever necessary their position can be adjusted with the aid of a 14mm spanner.
  • Page 6 Fit the flip-over length stop by feeding the head of the bolt into the T-shaped slot on the top side of the fence. The ratchet handle locks the stop in place. The stop plate can be flipped over to engage or disengage it. From underneath the carriage, push up the locating stop pin.
  • Page 7 With the tapered spindle locked, fit the upper spindle. Use a flat screwdriver to unscrew the locking ring in the centre of the upper spindle. Place the upper spindle over the taper and tighten the retaining screw by passing a 6mm Allen key into the centre of the spindle.
  • Page 8 Fence depth locking knob Fence depth Adjusting screw Fence fixing plate Fence width lock Loosen the fence depth locking knob and the silver fence width lock. Slide the fence over the fixing plate so that the mitred end of the fence is closest to the spindle.
  • Page 9 Installing the work stand 1. Take 4 panels and 4 columns from the main carton. 2. Take the following hardware from the work stand hardware bag. 16-Hex head screw M8X20 32-8MM flat washer 16-Hex Nut 3. Assemble the work stand as shown in Fig.1. Install the machine housing onto work stand.

  • Page 10: Wiring Diagram

    WIRING DIAGRAM...
  • Page 11 DIAGRAM 1 PART LIST 1 PART# DESCRIPTION PART# DESCRIPTION BODY STAND ASSEMBLY PULL ROD CAP BOLT M5*10 LOCATING SLEEVE PROTECTIVE COVER NUT M8 PHILLIPS SCREW M4*35 SPRING WASHER 8 EMERGENCY SWITCH FLAT WASHER M10 EMERGENCY SWITCH COVER SUPPORT SEAT EMERGENCY SWITCH BOX ECCENTRIC SHAFT WINDOW ROLLER...

  • Page 12: Part List

    DIAGRAM 2 PART LIST 2 PART# DESCRIPTION SIDE PLATE HEX BOLT M8*16 NUT M8 STAND LINKING PLATE...
  • Page 13 DIAGRAM 3 PART LIST 3 PART# DESCRIPTION PART# DESCRIPTION HEX BOLT M8*10 HEX BOLT M16*40 FLAT WASHER M8 CAP SCREW M8*40 HEX BOLT M6*12 SPRING WASHER M8 FLAT WASHER M6 NUT BUSH PLATE GEAR TUBE SPRING CLAMP BEARING 8103 BEARING 6204 LIFTING BUBE BRACKET C RING 47 GEAR BOX...
  • Page 14 DIAGRAM 4 PART LIST 4 PART# DESCRIPTION PART# DESCRIPTION LOCKING HANDLE LOCKING HANDLE EXHAUST COVER 27-32 LOCKING HANDLE M8*80*140 SQUARE LEADER ASSEMBLY FLAT WASHER M8 LOCKING HANDLE HEAD SCREW M5*10 LONG WASHER FENCE LOCK NUT M8 BOLT M8*45 LOCKING HANDLE HEAD SCREW M5*10 FLAT WASHER M8 SPLINT...

  • Page 15: Declaration Of Conformity

    Unit C, Manders Ind. Est., Old Heat h Road, Wolverhampton, WV1 2RP. Declare that the product: Designation: Spindle Moulder Model: SM8000 Complies with the following Directives: Single Spindle Vertical Moulding Machine See Certificate Standards & technical specifications referred to: Ref : BM EC-Type Examin. Certificate MSD Certificate No.

Table of Contents