Table of Contents
Advertisement
Quick Links
Operating Instructions
WPS01 Reverse Parking Assist System
Keep this user guide for future reference. Always retain your proof of purchase
Keep this user guide for future reference. Always retain your proof of purchase
in case of warranty service.
in case of warranty service.
www.oricom.com.au
www.oricom.com.au
Tutorial videos are available -oricom.com.au,
Tutorial videos are available -oricom.com.au,
select your model and scroll down to FAQ's
select your model and scroll down to FAQ's
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Oricom WPS01
- Page 1 Operating Instructions WPS01 Reverse Parking Assist System Keep this user guide for future reference. Always retain your proof of purchase Keep this user guide for future reference. Always retain your proof of purchase in case of warranty service. in case of warranty service.
-
Page 2: Table Of Contents
User manual Sensor bracket x 4 Oricom international do not guarantee or assume liability for collisions or damages while reversing the vehicle. Sensor gasket (10°) x 4 Sensor gasket (5°) x 4... -
Page 3: Product Information
80°C tones, if the system detects an obstacle. · Storage temperature: -40 ~ +85°C The Oricom WPS01 is a 4-sensor parking assist system, the sensors are connected to the Sensor control unit via cables, the control unit and the ·... -
Page 4: Self Test Instruction
Self Test Instruction Learning function for cars with tow-bars or spare wheels When reverse gear is selected, the system will test all sensors automatically. The system may false alarm if a tow-bar/ spare If all sensors are working properly, the blue LED light flashes once and the buzzer will beep once for wheel is installed at the rear of the vehicle and indication. -
Page 5: Attention
Attention Sensor maintenance Typical Alert distances False detection may occur in the following situations: Do not wash the sensor with high pressure equipment. Buzzer Voice <0.3m Be----------- STOP Please wash car with 0.3 Meter low-pressure water. Be---Be--- 0.3~0.6m 0.4 Meter 0.5 Meter 0.6 Meter Clean sensors in the... -
Page 6: Sensor Installation
Installation Tools Sensor Installation Bracket mount installation Pls adjust the sensor angle according to sensor height and bumper angle, avoid pointing towards the ground. H > 0.45m H < 0.65m 1.5m size: 19 mm 2.5m < 0.45m < 0.45m < 0.45m Estimated Installation Time:... - Page 7 Sensor spacing Add the angled spacer depending on required angle. = 1 / 8L = 2 / 8L = 1 / 8L Note: “L” equals total length of bumper Sensor positions c-b, b-a, a-b, b-c...
- Page 9 Changing the sensor head angle (if needed). If colour matching the sensor heads it is advisable to paint the heads in two parts to achieve the best finish. When the paint is dry remove excess paint from the silicone then clip back together.
- Page 10 Flush mount installation Carefully mark out hole positions according to sensor spacing on page 10, make sure you check surroundings to avoid any damage to vehicle prior to drilling, drill hole using 19mm hole saw. Insert sensor into hole and plug into sensor wire and ECU. NOTE: If the sensor is not flush when installed inside the hole, you can file the inside of the hole on a slight angle to have a flush finish with no gap.
-
Page 11: Buzzer Installation
Buzzer Installation Functional Test after Installation 1.5m Function test is performed by holding a wooden board (0.3 x 1m) standing at the back of the vehicle, reverse the vehicle slowly to test each alert respectively as shown in this manual. -
Page 12: Troubleshooting
· Make sure the sensors are clear of any debris 5. For further assistance, contact Oricom such as dirt / ice. Support: support@oricom.com.au · Please check for any damage to the sensor. -
Page 13: Express Warranty (Australia)
Important Information - Repair Notice Oricom will not be liable under this Express Warranty, and to the extent permitted by law will not be liable Please be aware that the repair of your products may result in the loss of any user-generated data (such as for any defect, loss, damage or injury arising out of or in connection with a: stored telephone numbers, text messages and contact information).
Need help?
Do you have a question about the WPS01 and is the answer not in the manual?
Questions and answers