Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for HEADRUSH FRFR-GO
Summary of Contents for HEADRUSH FRFR-GO
- Page 1 User Guide English...
-
Page 2: Table Of Contents
(4.1) Quick Start .......................... 5 (4.2) Example A: One FRFR-GO (Mono) ................5 (4.3) Example B: Two FRFR-GOs (Stereo) ............... 6 (4.4) Example C: One FRFR-GO (Stereo) AUX Input ............ 6 (5.0) Features ..............7 (5.1) Rear Panel ........................... 7 (5.2) Front Panel ........................ -
Page 3: (1.0) Introduction
Please refer to the included safety and warranty manual for more information. Caution: To reduce the risk of electric shock, do not connect a FRFR-GO to a power outlet while the grille is removed. -
Page 4: (3.0) Battery Charging
(3.0) Battery Charging For the quickest charging time, power off FRFR-GO and use the included power cable to connect the unit to a power outlet. A full charge can take up to 3 hours. The charge LED will illuminate with a corresponding color to show how much battery life is left. -
Page 5: (4.0) Setup
(4.0) Setup (4.1) Quick Start 1. While the power is switched off, plug the included power cable into FRFR-GO, then plug the cable into a power outlet. 2. Connect audio input sources (smartphone, tablet, etc.) to FRFR-GO. For best results, do not connect a guitar directly to FRFR-GO’s input as the circuitry is designed to only be connected to an amp modeler’s line output. -
Page 6: (4.3) Example B: Two Frfr-Gos (Stereo)
(4.4) Example C: One FRFR-GO (Stereo) AUX Input Connect the Right and Left (Mono) outputs of your or guitar bass multi-FX/amp modeling pedal using a “Y” cable - (2) 1/4" TS to (1) 1/8" TRS, to the AUX input of your FRFR-GO. Multi-FX/amp modeling pedal... -
Page 7: (5.0) Features
(5.0) Features (5.1) Rear Panel A. Power Input Use the included power cable to connect this input to a power outlet. Make sure the Power Switch is set to OFF when connecting or disconnecting the cable. B. Power Switch Use this switch to power the loudspeaker ON or OFF. Make sure the volume knobs are set to the minimum (counterclockwise) positions before turning it on. -
Page 8: (5.2) Front Panel
(5.2) Front Panel F G H I C. Charge LED This LED will be lit green when fully charged and lit red when charging. D. Power LED This LED will be lit green when the speaker is powered on. E. Input Use a 1/4”... -
Page 9: (6.0) Operation
(6.0) Operation (6.1) Pairing a Bluetooth Device 1. Power on the FRFR-GO. The Bluetooth LED will not be lit when the speaker is first powered on unless it was previously paired with a device before being powered off. Flip the switch to ON 2. -
Page 10: (7.0) Troubleshooting
If the sound is distorted: Try lowering the volume control of your amp modeler. You will want your amp modeler’s live-level output to be as close to unity gain (0 dB) without going over. For HeadRush modelers, set the main volume knob around “7”, depending on your rig’s setup. -
Page 11: (8.0) Appendix
HeadRush is a trademark of inMusic Brands, Inc., registered in the U.S. and other countries. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc., and any use of such marks by HeadRush is under license. All other product names, company names, trademarks, or trade names are those of their respective owners. - Page 12 Manual Version 1.0...
Need help?
Do you have a question about the FRFR-GO and is the answer not in the manual?
Questions and answers
Bluetooth hookup