Table of Contents
Advertisement
Quick Links
SUMMARY
1
PRODUCT IDENTIFICATION .................................................................................................................................. 3
1.1
APPLICATION, GENERAL FUNCTIONS AND INTENDED USE............................................................................. 3
1.2
NAME AND ADDRESS OF MANUFACTURER OR DISTRIBUTOR ........................................................................ 3
SMEG S.P.A. ............................................................................................................................................................ 3
1.3
DECLARATION OF CONFORMITY TO PRODUCT STANDARDS .......................................................................... 3
1.4
DESCRIPTION OF THE APPLIANCE ................................................................................................................. 4
2
SYMBOLS USED IN THE MANUAL ........................................................................................................................ 4
3
SAFETY PRECAUTIONS AND INSTRUCTIONS ........................................................................................................ 5
3.1
CORRECT INSTALLATION .............................................................................................................................. 5
3.2
SAFE USE...................................................................................................................................................... 6
3.3
CORRECT MAINTENANCE ............................................................................................................................. 7
4
PRODUCT CHARACTERISTICS ............................................................................................................................... 8
4.1
OVERALL DIMENSIONS ................................................................................................................................. 8
4.2
TECHNICAL CHARACTERISTICS ...................................................................................................................... 9
5
PREPARING THE APPLIANCE FOR USE.................................................................................................................10
5.1
POSITIONING AND INSTALLATION ...............................................................................................................10
5.2
CONNECTION TO THE WATER SUPPLY .........................................................................................................11
5.3
DRAIN CONNECTION ...................................................................................................................................12
5.4
CONNECTION TO THE ELECTRICITY SUPPLY ..................................................................................................12
6
FIRST START-UP..................................................................................................................................................13
6.1
FIRST START-UP ..........................................................................................................................................13
6.2
PREPARING FOR USE ( IMPORTANT ) ..........................................................................................................13
6.3
USING THE WATER SOFTENER (ON MODELS WITH THIS FEATURE ONLY)......................................................13
7
CONTROL PANEL ................................................................................................................................................14
7.1
SET-UP (AUTHORISED STAFF ONLY) ............................................................................................................15
7.2
CONTENTS OF DISPLAY ................................................................................................................................15
7.3
PARAMETER PROGRAMMING PROCEDURE (SETUP).....................................................................................16
7.4
MODIFIABLE PARAMETERS ..........................................................................................................................16
7.5
ADJUSTING DETERGENT AND RINSE AID DISPENSING (ONLY AVAILABLE ON CERTAIN MODELS) ...................17
7.6
CIRCUIT ..................................................................................................................................................................17
7.7
MAINS WATER HARDNESS SETTING TABLE (MODELS WITH SOFTENER ONLY) ..............................................18
ADJUSTING THE REGENERATION FREQUENCY (MODELS WITH SOFTENER ONLY) .....................................................18
7.8
7.9
7.10
7.11
8
MALFUNCTIONS SHOWN ON THE DISPLAY (FOR THE TECHNICIAN) ....................................................................20
9
INSTRUCTIONS FOR THE USER ............................................................................................................................22
9.1
BEFORE WASHING.......................................................................................................................................23
9.2
FIRST USE EACH DAY (TANK AND BOILER EMPTY) ........................................................................................24
9.3
PROGRAM CHANGE ....................................................................................................................................25
10
CHOSING THE PROGRAM ...............................................................................................................................26
11
BASKETS PROVIDED .......................................................................................................................................27
12
MAINTENANCE AN CLEANING ........................................................................................................................27
12.1
DAILY CLEANING OF FILTERS........................................................................................................................28
12.2
TOTAL PUMP-OUT AT THE END OF THE DAY ................................................................................................30
12.3
TOPPING UP WITH REGENERATING SALT (FOR MODELS WITH SOFTENER) ...................................................30
12.4
ROUTINE INSPECTION OF THE SPRAY ARM (ONCE A WEEK ) ........................................................................31
12.5
LENGTHY PERIODS OUT OF USE ...................................................................................................................31
13
TROUBLESHOOTING .......................................................................................................................................32
14
MALFUNCTIONS SHOWN ON THE DISPLAY (FOR THE USER) ...........................................................................34
TRANSLATION OF THE ORIGINAL INSTRUCTIONS
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Smeg SPH503
Summary of Contents for Smeg SPH503
-
Page 1: Table Of Contents
PRODUCT IDENTIFICATION ..........................3 APPLICATION, GENERAL FUNCTIONS AND INTENDED USE................3 NAME AND ADDRESS OF MANUFACTURER OR DISTRIBUTOR ................ 3 SMEG S.P.A................................3 DECLARATION OF CONFORMITY TO PRODUCT STANDARDS ................3 DESCRIPTION OF THE APPLIANCE ......................... 4 SYMBOLS USED IN THE MANUAL ........................4 SAFETY PRECAUTIONS AND INSTRUCTIONS ...................... - Page 2 SMEG thanks you for choosing one of its products. This manual is an integral part of the appliance. Take good care of it and keep it to hand throughout the appliance’s life cycle, since it contains important information about assembly, safety, use and maintenance.
-
Page 3: Product Identification
Electrical and Electronic Equipment (WEEE). For information on the treatment, recovery and recycling of this product, contact the local authority, domestic waste collection service, or your Smeg reseller. Make sure that this product is scrapped correctly to safeguard the environment and... -
Page 4: Description Of The Appliance
1.4 Description of the appliance U COVER (TOP) D DISPLAY AND CONTROL PANEL C HOOD HOOD OPENING / CLOSING HANDLE F ADJUSTABLE FEET 2 SYMBOLS USED IN THE MANUAL This symbol instructs the user to read the instructions in the manual with care. This symbol appears next to information important for the safety of people and the appliance. -
Page 5: Safety Precautions And Instructions
3 SAFETY PRECAUTIONS AND INSTRUCTIONS The precautions and instructions below contain important information and must be read with care. The manufacturer does not accept responsibility for damage caused by failure to comply with the safety precautions and instructions. 3.1 Correct installation ... -
Page 6: Safe Use
3.2 Safe use The staff assigned to use the dishwasher must be suitably trained and instructed. The appliance is not suitable for use by juveniles or persons with reduced physical, sensorial or mental capacities, or those without the necessary knowledge and experience. Such persons may only use the appliance under the supervision of a person responsible for their safety. -
Page 7: Correct Maintenance
3.3 Correct maintenance Do not clean the machine with a water jet machine, high-pressure or steam cleaners. Before performing any maintenance procedure on the appliance disconnect it from the mains electricity supply. Touching live electrical components, even accidentally, may be very dangerous. -
Page 8: Product Characteristics
4 PRODUCT CHARACTERISTICS 4.1 Overall dimensions LOWER BACK PANEL ELECTRICITY SUPPLY CABLE FILLER HOSE PERISTALTIC HOSES TERMINAL FOR EXTERNAL DRAIN HOSE EQUIPOTENTIAL CONDUCTOR. -
Page 9: Technical Characteristics
4.2 Technical characteristics Electricity supply Vedi targhetta caratteristiche e Intake water pressure schema elettrico Intake water temperature allegato alla macchina Interno Max. working altitude 2000 Working ambient temperature °C 10 - 35 Relative humidity 80% per temperature sino a 25 °C con diminuzione lineare sino a 50% alla temperatura... -
Page 10: Preparing The Appliance For Use
5 PREPARING THE APPLIANCE FOR USE Convey the dishwasher to the installation site, remove the packaging and check the appliance and components for damage; any damage found must be reported to the transporter in writing. The packaging components (plastic bags, expanded polystyrene, nails, etc.) must not be left within reach of children and pets since they are potentially dangerous. -
Page 11: Connection To The Water Supply
5.2 Connection to the water supply Check that the intake water pressure, flow rate and temperature are as stated in the dishwasher's technical characteristics. If the dynamic pressure exceeds the limit stated in technical characteristics, a pressure reducer must be installed. If the pressure is lower, it might be necessary to fit a special pump to ensure optimal performance. -
Page 12: Drain Connection
5.3 Drain connection The dishwasher is fitted with a drain pump and can operate with drain connections on the floor or wall. Before connecting the hose, check that the diameter and height of the wall drain connection are as stated in the dishwasher's technical characteristics. -
Page 13: First Start-Up
6 FIRST START-UP 6.1 First start-up The electrical protection system must undergo a functional test before the appliance is put into operation. The appliance must be installed and/or inspected by qualified staff, who will start it up for the first time and provide the relevant operating instructions. -
Page 14: Control Panel
7 CONTROL PANEL Key to Symbols On/off button Total pump-out (tank -boiler) button Regenerating salt symbol (only if softener is fitted) Short programme button Medium programme button Long programme button L1 Short programme Led L2 Medium programme Led L3 ... -
Page 15: Set-Up (Authorised Staff Only)
Using the buttons Long press, release, press Button Short press Pressed for 2” Pressed for 5” again Door open and machine OFF. Display temperatures Long press >>> display On/OF Boiler and tank reads “- -“ >>> release and press again: Access Setup Menu (1) Scroll through Setup Start Pump-... -
Page 16: Parameter Programming Procedure (Setup)
7.3 Parameter programming procedure (setup) To modify the parameters, proceed as follows starting with the appliance in “OF” status with the door open. 1) Switch the appliance using the On/OF button 2) Press and hold the button until the display shows “- -“ , release and press again. 3) Press the pump-out button to scroll through the parameters for modification 4) Modify the parameter by pressing button P1... -
Page 17: Adjusting Detergent And Rinse Aid Dispensing (Only Available On Certain Models)
7.5 Adjusting detergent and rinse aid dispensing (only available on certain models) NOTE: Do not exceed the amount indicated by the manufacturer, as shown on the package. An excessive amount may cause foaming. Rinse aid – Grams/liter dosage (depends on model)- The display reads “ri” Every time is pressed, the value increases of 0,1 g/l... -
Page 18: Mains Water Hardness Setting Table (Models With Softener Only)
7.7 Mains water hardness setting table (models with softener only) After a number of washing cycles corresponding to the set water hardness has been started, the dishwasher starts automatically the resin regeneration cycle, that lasts about 90 seconds. During this phase the machine load or unloads automatically, even though it isn’t performing a washing cycle. -
Page 19: Clean Water Cycle" Option - Display Reads "Cl
7.9 "Clean water cycle" option - Display reads “CL” When this option is activated, the appliance pumps out all the water from the tank and then refills it with clean water at every wash cycle. How long this operation takes depends on the washing water temperature. -
Page 20: Malfunctions Shown On The Display (For The Technician)
8 MALFUNCTIONS SHOWN ON THE DISPLAY (FOR THE TECHNICIAN) The dishwasher is able to identify a number of malfunctions and show them on the display. If the problem persists after the dishwasher has been switched off and back on, proceed as described below: Tank temperature probe Tank temperature probe disconnected or not working. - Page 21 Boiler water filling The boiler wasn’t filled in the expected time: check the water malfunction supply tap, the dynamic supply pressure, cleanliness of the inlet water filter, any damage of the water charging hose, or check the Er 25 following in this order: - faulty boiler pressure switch (it always detects “empty”), - leakage or unbinding of the tube (water runs inside the tube) - menu service wrong setting “rP”...
-
Page 22: Instructions For The User
9 INSTRUCTIONS FOR THE USER Control panel Key to Symbols On/off button Total pump-out (tank -boiler) button Regenerating salt symbol (only if softener is fitted) Short programme button Medium programme button Long programme button L1 Short programme Led L2 Medium programme Led L3 ... -
Page 23: Before Washing
Use only detergents and rinse aids for industrial dishwashers. Do not use detergents intended for hand washing. We recommend the use of Smeg products, specially developed for this dishwasher. When topping up the tanks, take care not to swap the products; this might damage the dishwasher and cause malfunctions. -
Page 24: First Use Each Day (Tank And Boiler Empty)
9.2 First use each day (tank and boiler empty) Door closed and master switch on ON: Press and hold for 2/3 seconds, Leds ON/OF light up and the firmware version and e revision are displayed (F xxx r xxx…); FILL is displayed afterwards. Tank filling starts. -
Page 25: Program Change
Unload the dishes. When the dishwasher is closed again, the system offers the last program run. 9.3 Program change With program started, press and hold it down to interrupt it. Change the program by pressing... -
Page 26: Chosing The Program
10 CHOSING THE PROGRAM When you scroll through the available programs, the program number (P1, P2, ..etc.) and its duration are shown first, alternating with the wash and rinse temperatures. DURATION SYMBOL PROGRAM TYPE OF DIRT Short Glasses and cups 1 min 30 s Glasses, cups and plates with Medium... -
Page 27: Baskets Provided
12 MAINTENANCE AN CLEANING We recommend regular servicing by a SMEG authorised service centre at least once a year, to guarantee optimal performance at all times. Consumables (e.g. peristaltic pump hoses) and/or parts subject to wear and tear must be replaced with genuine SMEG parts. -
Page 28: Daily Cleaning Of Filters
12.1 Daily cleaning of filters The filter group is made of 2 or 3 filtering elements, according to the model. Procedure to disassemble filters made of 3 filtering elements: a- Unfasten and remove the lower spray arm b- Lift and remove the two rectangular filters c- Rotate filter “C”, lift it and separate it extracting the central part “D”... - Page 29 Procedure to disassemble the filters made of 2 filtering elements: it is not necessary to remove the lower spray arm. a- Rotate filter “C”, lift it and separate it by extracting the central part “D” Filter “C” can have different depths, according to the model. When removing the filters, do not let the coarse residues fall into the basin under the filters;...
-
Page 30: Total Pump-Out At The End Of The Day
12.2 Total pump-out at the end of the day The dishwasher is able to perform an automatic cleaning cycle at the end of the day. Press the pump-out button for about 5”, the Led flashes and the pump-out and automatic tank cleaning phase starts. -
Page 31: Routine Inspection Of The Spray Arm (Once A Week )
12.4 Routine inspection of the spray arm (once a week ) Remove the inferior and superior spray arms. Releasing the retaining element “R” is enough to remove them. Clean the spray arms with clean flowing water, do not use tools which may cause damages. -
Page 32: Troubleshooting
13 TROUBLESHOOTING In case the pump is not working properly, follow the steps below: Empty the dishwasher out using a container and disconnect the power. Remove screw A, release tab B and lift it upwards. Make sure that the covered drain pump impeller can rotate freely, and that there are no dirt residues, limestone, or pieces of glass. - Page 33 Increase the duration of the washing Improper set cycle cycle, especially if the load is very dirty or partially dried. - Verify that the nozzles are clean and Clogged nozzles that the water softener, if present, is working correctly. Boiler incrusted with - Verify that the filter of the tube limescale placed inside the rinse aid jerrycan is...
-
Page 34: Malfunctions Shown On The Display (For The User)
14 MALFUNCTIONS SHOWN ON THE DISPLAY (FOR THE USER) The dishwasher can show a series of malfunctions on display. After the machine has been switched off and restarted, if the problem is not solved, follow the steps below: ( FOR A MORE PROFICIENT AFTER-SALES SERVICE, ALWAYS TAKE NOTE OF THE INDICATED ERROR ) Err04 Tank temperature probe anomaly Contact After-sales Service...
Need help?
Do you have a question about the SPH503 and is the answer not in the manual?
Questions and answers