Elecom NESTOUT FAN-NEST-GF1 Series Quick Start Manual

FAN-NEST-GF1 series
Model: FNGF1, FAN-NEST-GF1BK, FAN-NEST-GF1BE, FAN-NEST-GF1FBK
ENGLISH
Package Contents
Verify the package to ensure all contents are present prior to using the product. Every effort has been
made to ensure proper packaging, however any shortage or damage is discovered, contact the retailer
where the product was purchased.
Main unit
•
•
Tripod
•
•
Tripod mount screw
•
Connector
•
* The NESTOUT outdoor battery is not included. Please acquire a NESTOUT outdoor battery separately.
* The 2-port type NESTOUT outdoor battery cannot be connected directly to this product when a tripod
is attached. In this situation, use a commercially available USB cable to connect the NESTOUT
outdoor battery to the USB Type-C® port on this product.
* The cable for connecting to the USB Type-C port on this product is not included.
Please prepare one separately.
NESTOUT Outdoor Battery
1-port type
How to use
How to connect
①
Secure the tripod by screwing the tripod mount
screw into the tripod socket on the underside.
②
Open the cap of the NESTOUT outdoor battery
and attach the connector to it.
* Please pay attention to the orientation of the connector. The side
without the indent is the side that connects to the battery.
* Screw on the connector tightly until there is no gap.
* It may be a little difficult to screw on the connector. This is normal.
③
Check that the air volume dial on the main unit is
at OFF.
④
Check the orientation of the USB Type-C connector
on this product and the USB Type-C port on the
NESTOUT outdoor battery when connecting.
* Plug it in until there is no gap and it will be locked in.
⑤
Turn the air volume dial to turn on the fan, and
the fan blades will start rotating.
• The NESTOUT outdoor battery will turn off automatically when
not in use. If the NESTOUT outdoor battery power LED is not lit
up, press the battery power button to turn it on.
• The NESTOUT outdoor battery will turn OFF automatically after
approximately 2 hours, when the fan is left running on low. Gear
mode will allow for continuous use of approximately 12 hours.
Double click the power button on the side of the battery to turn
gear mode ON/OFF.
Gear mode ON  Power LED blinks
* Gear mode will be deactivated when the same action is performed, or
when the power is turned OFF.
• When using breeze mode, make sure gear mode is activated.
Malfunction may occur if gear mode is deactivated.
Manual
Pole clamp
* Only for FAN-NEST-GF1FBK
Storage case
2-port type
When using a tripod, a
commercially available
USB cable is required.
Portable Fan
Name and function of each part
Main unit
Joint screw
When using a mobile battery other than the NESTOUT outdoor battery or a power outlet
You can use this product with other commercial mobile batteries or AC adapters by
connecting to this product using a USB Type-C cable.
* USB cable and AC adapter are not included. Please prepare separately.
USB Type-C connector
Adjusting the wind power
Turn the air volume dial to turn on the fan, and to switch
between breeze mode, light, medium, and strong. Adjust it
to your preferred wind strength.
• Breeze mode produces a pleasant breeze incorporating
natural wind patterns. It replicates a light and
unpredictable wind like that of a gentle breeze.
• During breeze mode, the fan may vibrate because its
blades are rotating at a low speed. This is not a malfunction and you may continue
using it as it is.
• If the air volume dial is turned up rapidly through multiple levels, it may not adjust
properly. Turn it up carefully one level at a time. If the power output of the battery or
AC charger being used is insufficient, the product may malfunction or generate
weak wind even when operating the air volume dial. Use power supply with a port
capable of at least 5 V / 1.5 A output.
Adjusting the swing angle
Turn the swing angle dial to switch between no swing, 40°
swing, 70° swing, and 100° swing. Adjust it to your preferred
swing angle.
Turning on the timer
Turn the timer dial to switch between 60 minutes, 120 minutes,
and 240 minutes. Adjust it to your preferred duration.
Adjusting the vertical angle
①
Loosen the joint screw by
turning it around half a round
counterclockwise.
Power LED
②
Adjust the vertical angle of the fan
unit, then turn the joint screw
clockwise to tighten.
USB Type-C connector
Tripod socket
Handle
for hanging
Lock
* There are locks
on both sides.
Air volume dial
Timer dial
Swing angle
dial
Tripod Connector
Pole clamp
Tripod mount
screw
Compatible with output of 5 V 1.5 A or higher
USB Type-C port
• AC adapter
• Mobile battery
USB cable (commercially available)
Joint screw
USB Type-C port
Fan blade
Front guard
Storage case
* Only for FAN-NEST-GF1FBK