Subscribe to Our Youtube Channel
Summary of Contents for Dewenwils TLA-60-12DW Wi-Fi
- Page 1 Wi-Fi Landscape Power Unit TLA-60-12DW Wi-Fi [Instruction Manual] Please pay attention to the warning signs Read the instructions with caution before operating and keep it properly V30406...
- Page 2 WARNING: READ ALL INSTRUCTIONS before using the Wi-Fi Low Voltage Transformer. Compatible with 2.4 GHz Wi-Fi networks. If you have multiple routers in your home, especially under the same modem and using dynamic IP address mode, please notice the routers with same LAN IP address may cause IP address conflict and make the routers involved cannot access internet.
-
Page 3: Installation Instructions
Installation Instructions: IMPORTANT:Please refer to INSTALLATION INSTRUCTION before proceeding with Wi-Fi router connection. Wi-Fi Low Voltage Transformer must be installed before connecting to Wi-Fi router. Status Indicator BInking Llgh: Roady to connect to Wi-Fi router. Light continuously ON:Connection to W-Fi routar is complete and W-Fi Low Voltage Transformer is rsady for use via the app. - Page 4 INSTRUCTIONS: 1.Prepare the Cable Be careful when splitting the landscape cable. Do NOT expose the copper cable. Remove 1/2 inch of insulation from both cables and twist the ends. 2.Connect the cable to the Transformer Lay the transformer on a flat, stable surface and use screwdriver to connect the stripped ends of the cable under the terminal clamping plate.
- Page 5 3.Place Your Fixtures and Route the cable Lay your fixtures (not included) to your desired location. Be sure they do not exceed the 60-watt rating of the transformer. Coil the rest of the cable after connecting the last fixture. 4.Attach Your Fixtures Turn the transformer on.
- Page 6 INSTRUCTIONS: STEP 1: Software Installation Download the “dewenwils" App: Scan QR Code or search "dewenwils" in Google Play or the App Store to download and install the app. Note: All pictures shown are for illustration purpose only, the APP will be updated continuously, please refer to the latest APP interface to operate.
- Page 7 Auto Add Mode (Bluetooth Mode) • Turn on Bluetooth on the smartphone. • Open the “dewenwils” APP （Figure 1）and click the “+” at the top right list, it will find the Wi-Fi Low Voltage transformer automatically. （Figure 2）Tap “Go to add”, the interface in Figure 3 will appear, click the button to switch to the appropriate WiFi signal source, then type in WiFi password and click “next”...
- Page 8 Note: Automatic connection time of devices varies depending on the strength of WiFi signal, so please do not operate the phone. If the connection fails, please reconnect, or switch to other stronger WiFi signal sources, or keep your phone closer to the device, or connect it by following the Manually Mode below.
- Page 9 Figure 3 Figure 4 Figure 5 Figure 6...
- Page 10 Figure 7 Figure 8 1.Add Manually Mode • Click the "+" icon at the right corner and then choose the " Wi-Fi Low Voltage transformer". (Figure 9) • Please check the mode on the left side of at the top right corner, if it is not “EZ Mode”, please switch to “EZ Mode”.
- Page 11 Figure 9 Figure 10 Figure 11 Figure 12...
- Page 12 Figure 13 Figure 14 Figure 15...
- Page 13 STEP 4:Set the Function You Need 1.Interface Introduction Change Device Name ON/OFF button Timer Setting Button Current time setting display 2.Timer Function Introduction Tap “Timer”, the interface of Timer Schedule will appear.(Figure 16) Figure 16...
- Page 14 3.Countdown Tap "Countdown" to set the hours and minutes, and then tap the “ ” button. The Wi-Fi Low Voltage transformer will maintain the current state on or off until the end of the countdown. It will exit countdown mode automatically if you turn on/off manually.
- Page 15 Figure 19 Figure 20 Figure 21 Figure 22...
- Page 16 5.Circulate You can set the duration of each ON and OFF, Start and End time accord- ing to your needs. The ON/OFF schedule will repeat between the Start and End time. For example: Set a period from 9:00 AM to 3:00 PM on Monday through Friday, turn on your light for 1 hour , and off for 30 minutes.
- Page 17 6.Random Either +/-30 minutes than setting ON/OFF time, randomly control device when you are away from home. Figure 25 Figure 26 7.Astronomical The controlled device will turn on or off at (before or after) sunset or sunrise.
- Page 18 Figure 27 Figure 28 Figure 29...
- Page 19 Life" , select "Smart Life " and tap "Enable" to enable the Smart Life skills. 2. You will be directed to the account link page. Type in your "dewenwils "account and password, don't forget to select your country/ region where your account belongs to.
-
Page 20: Other Functions
Other Functions Change the device name Share the device with your family Enter family member’s “Smart Life”account to control the device. Create Group Devices under the same group can be controlled simultaneously... -
Page 21: Specifications
Specifications: Model: TLA-60-12DW Wi-Fi Input Voltage: 120VAC, 60Hz Output: 12VDC Max Power Rating: 60W FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with... -
Page 22: Fcc Statement
FCC STATEMENT: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the TLA-60-12DW Wi-Fi and is the answer not in the manual?
Questions and answers