NexiGo 0550 Manual

Product Introduction

The battery pack is specially designed for charging P-5 DualSense wireless controller. With the special indicator to show the battery capacity, it can help users to control and know battery condition at any time. With this function, this product can detect whether the P-5 DualSense wireless controller needs to be charged when connected to the battery pack. When the P-5 controller was fully charged, the output port of the battery pack will automatically close and enter the sleep state. This product behaves well in energy conservation and environmental protection and the built-in high capacity lithium battery can charge the controller for a long time.

Product Diagram

Product Features

1. The battery pack will close all output ports and enter into the dormant state in standby mode. At this time, it is in the state of low energy consumption to achieve energy conservation and environmental protection.
2. When the battery pack is in standby mode, the remaining battery can be inspected by the electricity quantity detection button. The electric quantity is detected from low to high through the LED indicator, and then the indicator will turn off automatically after 30 seconds or you can long press it for 2 seconds to turn off the indicator.
3. When the battery pack is undercharged, at first the LED indicator will display from high to low and then will show the corresponding remaining battery. The four battery indicator lights are always on when the charging pack is fully charged until the external power supply is removed
4. The charging method of the charging pack. First constant current then constant voltage charging rnethod.
5. When the battey pack is charging for your controller, the indicator to the remaining battery capacity will always be on which is convenient for you to control the power in the charging pack. The four battery indicator lights are always on when the charging bag is fully charged.
6. Power detection function: when the electric quantity decreases with charging for P-5 controller and becomes lower than the normal discharge range. The first LED indicator will flash quickly to indicate that the battery pack needs to be charged. When the electric quantity is completely out the LED indicator will go off and the output port wil be closed to protect the battery pack from being damaged by over-discharge
7. The output voltage will be closed automatically when the output port is short-circuited. You need to recharge the battery pack to activate.

Device Operating Mode

1. Start up the product after the electricity quantity detection button is pressed, the LED indicator will flash from low to high and be off automatically after 30s; If the external power supply is connected to the input port within 30s the LED indicator will be always on. Otherwise the output port will closed automatically after 30s.
2. Atter turning on the battery pack, you can detect the electric quantity and use the battery pack to charge the 2-5 controller.
3. When the battery pack is not in use you can long press the detection button for 2s to turn off the battery pack or it will tum off automatically after 30s
4. Working mode this product is subject to the following three modes
   • Standby Mode: When the battery pack is in standby mode can detect the electric quantity of the battery; Without charging and discharging the battery pack you can short pres the electric quantity detection button to display the remaining electric quantity,
   • Charging Mode (Charged by external adapter or USB cable):
     1. When you charge the battery pack with 5V/1A adapter. the number of always-on LED indicator lights represents the battery capacity ofthe battery pack.
     2. After the battery pack is fully charged, the four LED indicators wil not turn off until the 5V/1A adapter is plugged out.
     3. When the 5V/1A adapter is used to charge the battery pack the charging and discharging of the battery pack cannot be conducted simultaneously.
   • Discharge Mode (Charge the P-5 controller with battery pack):
     1. When you use the battery pack to charge the P-5 controller, you should plug the controller into the output port of the battery pack when the battery pack detects the P-5 controller, the output port wil be accessed automatically at this time the battery pack ischarging the P-5 controller.
     2. When the battery pack is under discharging (charging the P-5 controller): The LED indicator light will display based on the battery capacity.
     3. When the battery capacity is less than 10% of battery capacity, the minimum power indicator will be flashing.
     4. After the P-5 controller is fully charged, the discharging current will less than 65mA for 30s and the battery pack will close the output port automatically. You also can long-press the charging control button for 2 seconds to cut off the charging output.

Product Specifications

Built-in lithium battery capacity: 3.7V/1500mAh
Over-charged protection voltage: 4.2V ±0.05V
Over-discharged protection voltage: 2.8V ±0.1V
Input current and voltage: 5V/1A
Charging current: 600mA ± 10mA
Charging time: About 3 hours (please use the 5V/1A power adapter to charge the battery pack)
Output current and voltage to discharge: MAX 5V/560mA
Quiescent current: 20uA
Operating temperature: 0°C-40°C
Storage temperature: -20°C-45°C

Attentions

1. Please use the 5V/1A power adapter to charge the battery pack. If the USB port of the computer is used the charging time will be longer.
2. The power adapter should be unplugged when the battery pack is fully charged or not in use.
3. It is recommended that the battery pack should be fuIly charged before using for the first tlme.
4. The battery cannot be used and stored in a humid environment.
5. Do not store the battery pack at a high temperature, otherwise the battery pack will be overheated and degrade the performance.
6. Please use the product within the specified temperature range otherwise, the battery performance of the battery pack will be reduced.
7. The battery pack should be kept of dust and heavy loads to guarantee its service life.
8. Please do not use the battery pack that is soaked, crushed, or broken and with electrical performance problems caused by improper use.
9. Do not use extemal heating equipment such as microwave ovens for drying.
10. If it is damaged, please send it to the maintenance department for repair. Do not disassembly it by yourself.
11. Keep this product away from children.

Contact Info

Brand: NexiGo
Website: www.nexigo.com
Manufacturer Nexight INC
Email: cs@nexigo.com
Tel: +1(458)215-6088
Address: 11075 SW 11th St Beaverton, OR 97005, US

If you have any problems please contact us at cs@nexigo.com at any time for further assistance. This product is covered by our generous 1-year manufacturers warranty, please visit www.nexigo.com for more warranty information and register on www.nexigo.com/warranty for an EXTRA ONE YEAR warranty.

Documents / Resources

References

• NexiGo | Home Theater Projectors & Video Collaborations
• NexiGo Warranty Registration | NexiGo

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download NexiGo 0550 Manual