Subscribe to Our Youtube Channel
Related Manuals for Siemens SR85E801LE
Summary of Contents for Siemens SR85E801LE
- Page 1 SR85E801LE Dishwasher EN Information for Use Register your appliance on My Siemens and discover exclusive services and offers. Siemens Home Appliances...
-
Page 2: Table Of Contents
Further information and explanations are available online: Table of contents 1 Safety ........... 4 7 Programmes ...... 19 1.1 General information.... 4 7.1 Information for test institutes ... 20 1.2 Intended use...... 4 7.2 Favourite ...... 20 1.3 Restriction on user group.. 4 8 Additional functions .... 21 1.4 Safe installation ...... - Page 3 13 Detergent ......... 29 20 Transportation, storage and disposal ........ 53 13.1 Suitable detergents .... 29 20.1 Removing the appliance .. 53 13.2 Unsuitable detergents ... 30 20.2 Protect appliance from frost.. 54 13.3 Information on detergents .. 30 20.3 Transporting the appliance ... 54 13.4 Adding detergent....
-
Page 4: Safety
en Safety 1 Safety Observe the following safety instructions. 1.1 General information Read this instruction manual carefully. ¡ Keep the instruction manual and the product information safe ¡ for future reference or for the next owner. Do not connect the appliance if it has been damaged in transit. ¡... - Page 5 Safety en WARNING ‒ Risk of electric shock! Incorrect installation is dangerous. Connect and operate the appliance only in accordance with the ▶ specifications on the rating plate. Always use the supplied power cable for the new appliance. ▶ Connect the appliance to a power supply with alternating cur- ▶...
-
Page 6: Safe Use
en Safety Contact between the appliance and installation lines may lead to a defect in these lines, e.g. gas pipes and power lines. Gas from a corroded gas pipe can ignite. A damaged power line can cause a short circuit. Check that there is a distance of at least 5 cm between the ap- ▶... - Page 7 Safety en Highly caustic alkaline or highly acidic cleaning agents in conjunc- tion with aluminium parts in the interior of the appliance may cause explosions. Never use highly caustic alkaline or highly acidic cleaning ▶ agents, in particular commercial or industrial products, in con- junction with aluminium parts (e.g.
-
Page 8: Damaged Appliance
en Safety 1.6 Damaged appliance WARNING ‒ Risk of electric shock! If the appliance or the power cord is damaged, this is dangerous. Never operate a damaged appliance. ▶ Never operate an appliance with a cracked or fractured surface. ▶ Never pull on the power cord to unplug the appliance. Always ▶... -
Page 9: Safety Systems
Safety en WARNING ‒ Risk of harm to health! Children can lock themselves in the appliance, thereby putting their lives at risk. With redundant appliances, unplug the power cord. Then cut ▶ through the cord and damage the lock on the appliance door beyond repair so that the appliance door will no longer close. -
Page 10: Preventing Material Damage
en Preventing material damage Modified or damaged water hoses Preventing material damage 2 Preventing material may result in material damage and damage to the appliance. damage Never kink, crush, modify or cut ▶ through water hoses. Preventing material damage 2.1 Safe installation Only use the water hoses supplied ▶... -
Page 11: Childproof Lock
Childproof lock en So as not to scratch the finish on ▶ Environmental protection and saving energy 4 Environmental protec- the appliance, do not use sponges with a rough surface or abrasive tion and saving energy cleaning agents. To prevent corrosion, do not use Environmental protection and saving energy ▶... -
Page 12: Autoopen Dry
en Installation and connection shortened. Sensor set- Description → "Overview of the basic settings", ting Page 36 SE:00 Optimum setting for If this additional function has been a mixed load and selected, automatic door opening is heavily soiled table- deactivated. ware. Saves both en- → "Additional functions", Page 21 ergy and water. -
Page 13: Installing And Connecting The Appliance
Installation and connection en When doing so, check that the 5.2 Installing and connecting wastewater hose is not kinked, the appliance crushed or twisted. You can position your built-under or Also check that there is no cover integrable appliance in a fitted kit- in the drainage system preventing chen between wooden and plastic the wastewater from being dis-... - Page 14 en Installation and connection Insert the mains plug of the appli- ance's power cable in a socket nearby. The connection data of the appli- ance can be found on the rating plate. Check the mains plug is inserted properly.
-
Page 15: Familiarising Yourself With Your Appliance
Familiarising yourself with your appliance en Familiarising yourself with your appliance 6 Familiarising yourself with your appliance Familiarising yourself with your appliance 6.1 Appliance You can find an overview of the parts of your appliance here. Rating plate Rating plate with E number and FD num- ber → Page 55. - Page 16 en Familiarising yourself with your appliance Detergent dispenser Add detergent to the detergent dispenser. → "Detergent", Page 29 Bottom basket Bottom basket → Page 23 Filter system Filter system → Page 45 Dispenser for special salt Add special salt to the dispenser for spe- cial salt. → "Water softening system", Page 25 Tablet collecting tray During the wash cycle tablets automatic- ally fall out of the detergent dispenser into...
-
Page 17: Controls
Familiarising yourself with your appliance en 6.2 Controls You can use the control panel to configure all functions of your appliance and to obtain information about the operating status. With some buttons you can perform different functions. 3 4 5 6 ON/OFF button and reset Switching on the appliance button... - Page 18 en Familiarising yourself with your appliance Timer programming Setting timer programming → Page 35 Door handle Open the appliance door. → Page 34 Display The display shows information about the remaining running time or the ba- sic settings. You can change the ba- sic settings via the display and the setting buttons.
- Page 19 Programmes en Programmes 7 Programmes You can find an overview of the pro- ted. The running time will change if Programmes grammes that can be selected here. the rinse aid system is switched off Different programmes, which can be or rinse aid needs to be added. found on the control panel of your The consumption values can be appliance, are available depending...
-
Page 20: Information For Test Institutes
en Programmes Programme Programme se- quence Tableware: Time-optimised: Delicate tableware, cutlery, tem- Cleaning 45 °C ¡ ¡ Speed 45° perature-sensitive plastics and Intermediate rinse ¡ glasses Final rinse 55 °C ¡ Level of soiling: Lightly adhering fresh food rem- ¡ nants Use only if appliance is unloaded. Machine Care 70 °C Machine Care → "Favourite ", Page 20... -
Page 21: Additional Functions
Additional functions en Additional functions 8 Additional functions You can find an overview of the additional functions that can be selected here. Additional functions Different additional functions, which can be found on the control panel of your appliance, are available depending on the appliance configuration. You can se- lect certain additional functions depending on the programme. -
Page 22: Features
en Features Press in the levers on the right and Features 9 Features left on the outside of the basket. You can find an overview of the pos- Features sible features of your appliance and how to use them here. These features depend on the model of your appliance. -
Page 23: Knife Shelf
Features en 9.2 Knife shelf 9.4 Bottom basket Use the shelf for knives and long Arrange pans and plates in the bot- items of cutlery. tom basket. Cutlery basket 9.3 Etagere Large plates up to a diameter of 31 cm can be arranged in the bottom Use the cutlery shelf and space un- basket as shown. -
Page 24: Folding Prongs
en Features 9.5 Folding prongs 9.6 Cutlery basket Use the folding prongs to position Arrange cutlery in the cutlery basket, tableware securely, e.g. plates. always without sorting it and with the sharp points downwards. You can fold the prongs down to po- sition pans, bowls and glasses 9.7 Bottle holder better. -
Page 25: Before Using For The First Time
Before using for the first time en Add detergent → Page 29. Before using for the first time 10 Before using for the Start the Programme with the first time highest cleaning temperature without tableware. Before using for the first time To remove any marks from water 10.1 Performing the initial or other residues, we recommend configuration... -
Page 26: Setting The Water Softening System
en Water softening system Water hardness Hardness range mmol/l Setting value °E 39 - 62 Hard 5.5 - 8.9 H:07 Note: Set the water hardness determ- hardness. The higher the water hard- ined on your appliance. ness, the greater the consumption of special salt. -
Page 27: Switching Off The Water Softening System
Water softening system en Place the lid back on the dis- 11.5 Regeneration of the wa- penser and turn to close. ter softening system 11.4 Switching off the water In order to obtain fault-free function of the water softening system, the appli- softening system ance performs regeneration of the If you find the special salt refill indic- water softening system at regular in-... -
Page 28: Rinse Aid System
en Rinse aid system Close the lid of the dispenser for Rinse aid system 12 Rinse aid system rinse aid. The lid clicks into position. Rinse aid system 12.1 Rinse aid 12.2 Setting the amount of For optimum drying results, use rinse rinse aid aid. -
Page 29: Detergent
Detergent en The display shows H:xx. Powder detergent The display shows . Powder detergent is recommended Press repeatedly until for shorter programmes. the display shows the value r:04 The dosage can be adjusted to the set at the factory. level of soiling. Press repeatedly until the dis- Liquid detergent... -
Page 30: Unsuitable Detergents
en Detergent According to the manufacturers, ness, usually 26 °E, without combined detergents generally only adding special salt. For the best function up to a water hardness of washing and drying results we re- 26 °E. With a water hardness above commend using special salt from a 26 °E you will need to add special water hardness of 17 °E. - Page 31 Tableware en Add the detergent to the dry deter- Close the lid of the detergent dis- gent dispenser. penser. 50 ml 25 ml 15 ml If you are using tablets, one is The lid clicks into position. enough. Insert the tablets in a hori- The detergent dispenser will open zontal position.
-
Page 32: Tableware
en Tableware 14.1 Damage to glass and Cause Recommenda- tion tableware Highly caustic al- If you are using Only put glasses and china in the kaline or highly highly caustic al- dishwasher if it is marked as dish- acidic cleaning kaline or highly washer-safe by the manufacturer. - Page 33 Tableware en allowing steam to escape and water To save resources, do not pre- to leak out around the door. This rinse tableware under running wa- could damage your kitchen units. ter. Observe the following when arran- ging tableware: – Put heavily soiled tableware in the bottom basket, e.g.
-
Page 34: Removing Tableware
en Basic operation The Eco 50° programme is set by 14.3 Removing tableware default. The Eco 50° programme is espe- WARNING cially environmentally friendly and Risk of injury! ideal for normally soiled tableware. Hot tableware can cause burns to the It is the most efficient programme skin. -
Page 35: Setting Timer Programming
Basic operation en will help prevent excess pressure 15.5 Setting timer program- building up in the appliance and stop ming the appliance door bursting open. You can delay the start of the pro- Open the appliance door carefully. gramme by up to 24 hours. Press ... -
Page 36: Basic Settings
en Basic settings Basic settings 16 Basic settings You can configure the basic settings for your appliance to meet your needs. Basic settings 16.1 Overview of the basic settings The basic settings depend on the features of your appliance. Basic setting Display text Selection Description Water hardness H:04... - Page 37 Basic settings en Basic setting Display text Selection Description EmotionLight EL:01 EL:00 - EL:02 Interior light. With the setting "EL:00"m ¡ the interior light is switched off. With the setting "EL:01", ¡ the interior light can be activated via the ON/OFF button.
- Page 38 en Basic settings Basic setting Display text Selection Description Start programme SP:01 SP:00 - SP:01 Set a default programme for when the appliance is switched on. With the setting "SP:00", ¡ the last programme selec- ted is set by default when the appliance is switched With the setting "SP:01", ¡...
- Page 39 Basic settings en Basic setting Display text Selection Description Door opening c:00 c:00 - c:03 Electric door opening is ¡ activated with the setting "c:00". You open the ap- pliance door by pressing on the upper middle sec- tion of the appliance door once.
- Page 40 en Basic settings Basic setting Display text Selection Description autoOpen Dry o:02 o:00 - o:02 Activate or deactivate auto- matic opening of the appli- ance door during the drying phase. If the function has been ac- tivated, the running time may increase.
-
Page 41: Changing Basic Settings
Home Connect en Basic setting Display text Selection Description Remote Start rc:01 rc:00 - rc:02 Activate or deactivate → "Remote Start ", Page 42. The following settings are possible: With the setting "rc:00", ¡ the function is perman- ently deactivated. With the setting "rc:01", ¡... -
Page 42: Setting Up The Home Connect App
en Home Connect depends on the availability of Open the Home Connect app and Home Connect services in your coun- scan the following QR code. try. You can find information about this at: www.home-connect.com. To be able to use Home Connect, you must first set up the connection to the WLAN home network (Wi-Fi and to the Home Connect app. -
Page 43: Data Protection
Cleaning and servicing en 17.4 Data protection Cleaning and servicing 18 Cleaning and servi- Please see the information on data cing protection. The first time your appliance is To keep your appliance working effi- Cleaning and servicing registered on a home network ciently for a long time, it is important connected to the Internet, your to clean and maintain it carefully. -
Page 44: Machine Care
Dishwasher Care and Ma- ance to malfunction. To avoid such chine Cleaner for Dishwashers online faults and reduce odours, we recom- at https://www.siemens-home.bsh- mend cleaning your appliance at reg- group.com/store or from customer ular intervals. service. -
Page 45: Filter System
Cleaning and servicing en Follow the safety instructions given ¡ Cleaning filters on the packagings of the machine Soiling in the dishwashing water may care products and machine clean- block the filters. ers. After each wash check the filters Remove any coarse soiling in the for residue. -
Page 46: Cleaning Spray Arms
en Cleaning and servicing Press the locking catches 18.6 Cleaning spray arms gether and lift the coarse filter out Limescale and soiling in the dish- . washing water may block the nozzles and bearings on the spray arms. Clean the spray arms regularly. Unscrew the upper spray arms and pull down to remove Clean the filter elements under run-... -
Page 47: Troubleshooting
This will avoid unneces- sary costs. Tip: You can find further information and explanations on troubleshooting on- line by scanning the QR code in the table of contents and on our website siemens-home.bsh-group.com. WARNING Risk of electric shock! Incorrect repairs are dangerous. - Page 48 en Troubleshooting Fault Cause and troubleshooting E:32-00 will light up Water tap is jammed or furred up. alternately or indicator Turn on the water tap. ▶ for water supply lights The flow rate must be at least 10 l/min when the water supply is open.
- Page 49 Troubleshooting en Fault Cause and troubleshooting E:61-03 will light up Not an appliance fault. Siphon connection is still alternately. Water is closed or the wastewater hose is kinked or blocked. not drained. Check the connection to the siphon and open if ne- cessary.
- Page 50 en Troubleshooting Fault Cause and troubleshooting All LEDs lit up or Electronics have detected a fault. flashing. Press the main switch button for approx. 4 seconds. The appliance is reset and restarted. If the problem occurs again: Switch off the appliance. ‒ Pull out the mains plug or switch off the fuse in ‒...
- Page 51 Troubleshooting en Fault Cause and troubleshooting Remnants of food on Select a more intensive washing programme. ▶ tableware. → "Programmes", Page 19 Adjust the sensitivity of the sensors. ▶ → "Sensors", Page 11 Tableware has been precleaned too intensely. The sensors chose a weaker programme. Stubborn soiling cannot be entirely removed.
- Page 52 en Troubleshooting Fault Cause and troubleshooting Removable streaks Adjust the sensitivity of the sensors. ▶ are present on → "Sensors", Page 11 glasses, glassware with a metallic appear- ance and cutlery. Rust spots on cutlery. Cutlery is not sufficiently rust-resistant. Knife blades are often more severely affected. Use rust-resistant tableware.
-
Page 53: Clean Wastewater Pump
Transportation, storage and disposal en Insert the pump cover and press 19.1 Clean wastewater pump down . Large remnants of food or foreign bodies can block the waste water pump. As soon as the rinsing water no longer drains properly, the waste water pump must be cleaned. -
Page 54: Protect Appliance From Frost
en Customer Service 20.2 Protect appliance from 20.4 Disposing of old appli- frost ance If there is a risk of frost where the ap- Valuable raw materials can be re- pliance will be standing, e.g. in a holi- used by recycling. day home, empty the appliance com- pletely. -
Page 55: Product Number (E-Nr.), Production Number (Fd) And Consecutive Numbering (Z-Nr.)
Customer Service en Customer Service for a period of at 21.2 AQUA-STOP guarantee least 10 years from the date on In addition to warranty claims against which your appliance was placed on the seller under the purchase agree- the market within the European Eco- ment and in addition to our manufac- nomic Area. -
Page 56: Technical Specifications
en Technical specifications Technical specifications 22 Technical specifications Technical specifications Weight Max.: 45 kg Voltage 220 - 240 V, 50 Hz or 60 Hz Power rating 2000 - 2400 W Fuse 10 - 16 A Water pressure min. 50 kPa (0.5 bar) ¡ max. 1000 kPa (10 bar) ¡ Inlet rate Min. 10 l/min Water temperature Cold water. -
Page 57: Statement Of Compliance For Great Britain
Declaration of Conformity en essential requirements and other rel- A detailed Declaration of Conformity evant provisions of Directive can be found online at siemens- 2014/53/EU. home.bsh-group.com/uk/ among the A detailed RED Declaration of Con- additional documents on the product formity can be found online at page for your appliance. - Page 58 en Declaration of Conformity The manufacturer, BSH Hausgeräte GmbH deems that it has complied with provision 5.1-1 of ETSI EN 303 ¡ 645 v2.1.1 and, where relevant, provision 5.1-2 of ETSI EN 303 645 v2.1.1; provision 5.2-1 of ETSI EN 303 ¡...
- Page 60 EN Manufactured by BSH Hausgeräte GmbH under the trademark licence of Siemens AG Valid within Great Britain: Imported to Great Britain by BSH Home Appliances Ltd. Grand Union House Old Wolverton Road Wolverton, Milton Keynes MK12 5PT United Kingdom BSH Hausgeräte GmbH Carl-Wery-Straße 34...
Need help?
Do you have a question about the SR85E801LE and is the answer not in the manual?
Questions and answers