arboleaf CS20W Manual

Table of Contents

Contents

1 Introduction
2 Scale Display
3 Measurement Tips
- 3.1 DO's
- 3.2 DON'Ts
4 Package Contents
5 Specifications
6 Power Up Scale
7 Initial Setup
8 Take Measurements
9 Trouble Shooting
- 9.1 No wireless connection between your scale and the app
- 9.2 A non-zero number on scale
10 Documents / Resources
- 10.1 References
- 10.2 Download manual

Introduction

Arboleaf@ Body Composition Smart Scale measures weight, body fat percentage, BMI and other body composition data using bioelectrical impedance analysis (BIA) technology. This smart scale is intended for home use only.

Scale Display

Measurement Tips

information Tips: When you get the new scale, you first have to connect to the App in order to see body fat and other data on the scale.

Measurement Tips

To have accurate, consistent and comparable measurement results, there are some DOS and DON'Ts.

DO's

Place the scale on a flat hard surface.
Stand straight on the scale with barefoot, no socks and no shoes. Both feet uniformly touch the four metal electrodes.
Do calibration each time. Wait for "CAL" back to "0.0" then step on the scale for measurements.
Use the scale under the same condition during same hour each day.
Empty your bladder before weighing.

DON'Ts

Do not measure with socks or shoes on. Do not measure during or immediately after a strenuous exercise.
Do not measure immediately after shower, bath or sauna.
Do not measure after heavy alcohol consumption.
Do not measure when you have a fever.

Your body compositions may not be accurate after shower or heavy physical activities.
This smart scale model is not intended for use by infants or toddlers. Some body composition measurements are not for children under
Arboleaf smart scale should not be used for treating or diagnosing any medical conditions. Always consult your physician or health professional to determine what is suited for you.

Please read carefully before use

Do not use if you have a pacemaker, or any other internal medical devices in your body.
Do not use if you are pregnant.
Do not use on slippery floors.
Do not use when your body is wet.

Package Contents

Smart Scale
3 AAA Batteries
User Guide

Specifications

Dimensions: 11.8"x 11.8"x 0.94"(300mm x 300mm x 24mm)
Weight: 3.6lb (1.65kg)
Maximum Weight: 500lb/226.8kg
Minimum Weight: 0.4lb /C).2kg
Power: 3 AAA batteries

Power Up Scale

Your scale shipment comes with 3 AAA batteries. Put the batteries in the battery compartment. Your scale should display: 0.0. The scale is ready for use.

Initial Setup

Step 1: Download "Arboleaf' app and create an account

From Apple App Store (iOS) or Google Play (Android), search for "Arboleaf" and download it to your smart phone.

You can also scan the QR code to download.

Download "Arboleaf" app or scan the QR code
Register an account

Step 2: Pair scale with smartphone

Make sure Bluetooth is enabled on your phone. For Android 6.0 and above, Location also needs to be enabled.
Pairing is done automatically. Bluetooth icon is displayed on the scale.

Open Arboleaf app
Apply pressure to turn on scale

Take Measurements

Keep your app open on "Home" screen.

Apply pressure to turn on scale, wait for "CAL" back to "0.0"
Step on the scale barefoot until numbers are stable
Check numbers measurements

When the display number flashes twice, it indicates that the weight measurement has finished. When the light bar stops moving back and forth, the body fat and other body composition measurements have completed.
Take Measurements

Trouble Shooting

No wireless connection between your scale and the app

Reinstall Arboleaf app. Exit from the app (go to "Me" -> " Log Out" at bottom), then delete the app. Go to Apple App Store or Google Play to install Arboleaf app again.
Turn off Bluetooth then turn on Bluetooth again (go to your phone's Settings).
Power on reset your scale. Pull out batteries from your scale and put them back in.
For Android 6.0 and above, Location needs to be enabled.