Pioneer RX-322 Operating Instructions Manual

Operating
Instructions
Thank you for buying this Pioneer product.
Please read through these operating instructions so you will
know how to operate your model properly. After you have fi-
nished reading the instructions, put them away in a safe place for
future reference.
in some countries or regions, the shape of the power plug and
power outlet may sometimes differ from that shown in the
explanatory drawings. However, the method of connecting and
operating the unit is the same.
WARNING: To prevent FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT NOTICE
(For U.S. and Canadian models]
The serial number for this equipment is located on the rear panel.
Please write this serial number on your enclosed warranty card
and keep it in a secure area. This is for your security.
[For Canadian models]
CAUTION: to prevent ELECTRIC SHOCK DO NOT USE
THIS (POLARIZED}PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE
FULLY INSERTED TO PREVENT BLADE EXPOSURE.
ATTENTION: pour pREVENIR LES CHOCS
ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE
AVEC UN PROLONGATEUR UNE PRISE DE COURANT OU UNE
AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT
ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A
DECOUVERT.
TWO VOLTAGE SELECTOR SWITCHES
Only multi-vohtage models are provided with these switches.
U.S. and Canadian models are not provided with these switches.
Mains voltages in Saudi Arabia are 127V and 220V only.
Never use this model with 110V setting in Saudi Arabia.
CHECKING ACCESSORY ITEMS...
BEFORE OPERATION......
ANTENNA CONNECTIONS
CONNECTIONS .......
SURROUND SYSTEM .
PANEL FACILITIES ...
REMOTE CONTROL U
TURNTABLE FACILITIES .........,
GRAPHIC EQUALIZER CONTROLS
DOONDRWWwW
a
CONTENTS
WAsree
STEREO CASSETTE TAPE DECK RECEIVER
KX-322
STEREO TURNTABLE
BE 222277 S227,
Pe s222
English =
[pax
Espafial
The line voitage selector switches are on the rear pane!. Before
your model is shipped from the factory, these switches are set to
the power requirements of the destination. Check they are set
properly before plugging the power cord into the household wall
socket. if the voltage is not properly set or if you move to an area
where the voltage requirements differ, adjust the selector
switches as follows.
1. Use a medium-size screwdriver.
2. First, insert a screwdriver into the groove of the voltage
selector at the top, and adjust so that tip of the groove points
to the voitage value of your area
3. Next, insert the screwdriver into the groove of the voltage
selector at the bottom and adjust until the voltage is the same
as at the top.
Both switches must
be in the same switch
setting.
CHANNEL STEP SWITCH
Only multi-voltage models are provided with this switch.
U.S. and Canadian models are not provided with this switch.
{This switch is on the rear panel.)
The unit has been factory preset to the channel allocation for the
area in which it is to be sold, If the value is set incorrectly, the
frequency display may stop at the wrong frequency, or sound
may be distorted, resulting in an inability to reproduce reception
signals at their proper sound quality.
For this reason, be sure to confirm that the value is set correctly
before first using the unit.
[100 kHz/10 kHz] position:
Set to this position for areas with FM CHANNEL STEP
reception step of 100 kHz, AM 10 FM/AM
reception step of 50 kHz, AM 9 kHz.
When unsure about the channel allocation for your area, consult
your dealer for correct information.
PRELIMINARY OPERATIONS
BASIC OPERATIONS.
TAPE COPYING
RECORDING AND PLAYBACK
USING THE OPTIONAL AUDIO TIMER.........0.020 14
MAINTENANCE ......
TROUBLESHOOTING
SPECIFICATIONS...
HOW TO HANDLE CASSETTE TAPES
@Q PIONEER'
The future of sound and vision.