Jabra GN8110 User Manual page 2

English
GN 8110 USB
To see the illustrations, first unfold the back cover.
GN 8110 USB Set Up
System Requirements
The GN 8110 USB requires the following operating system:
• Windows 98 SE (Second Edition)
• Windows 2000
• Windows ME (Millennium Edition)
• Macintosh OS 9.0.4 or greater
You must have an available USB port. The GN 8110 USB does not work with earlier releases of these operating systems.
General
For Windows ME or Macintosh OS 9.0.4: You do not need to install any software. Simply plug the USB connector u into
any USB port on the computer.
For Windows 98 SE and Windows 2000: To use the GN 8110 USB the first time, you need to install the USB drivers necessary
for the computer to recognise the device.
Connect the GN 8110 USB to your Computer – Windows 98 SE and 2000
Turn on your computer and let it complete the boot-up process. Make sure that you are not running any applications.
Plug the USB connector u from the GN 8110 USB into any available USB port on the computer. Your headset does not
need to be plugged in at this time. The first time Windows detects that the device is connected, it recognises that there is
new hardware required and automatically launches the Add New Hardware Wizard.
The Add New Hardware Wizard will launch three times, installing the following drivers:
• USB Composite Device (INF\USB\INF)
• USB Human Interface Device (INF\HIDDEV.INF)
• USB Audio Device (INF\WDMA_USB.INF)
These drivers are typically pre-loaded in Windows. No additional software is needed. If you upgraded your system to Windows
98 SE or Windows ME, you may need to use the upgrade disc during this installation.
Add New Hardware Wizard – USB Composite Device
1 The Add New Hardware Wizard indicates that is has found the new USB Composite Device. Click Next.
2 The Wizards prompts you to search for the best driver for your device or select the driver you want from a displayed list.
Select Search for the best driver for your device. Click Next.
3 Windows now searches for new drivers in a specific location. Uncheck all the boxes. Click Next.
4 The Wizard indicates that it is ready to install the best driver for this device. Click Next to install the driver.
Click Finish when the Wizard is complete.
Add New Hardware Wizard – Human Interface Device
5 Next, the Wizard automatically installs the USB Human Interface Device. The Add New Hardware Wizard indicates that it
has found the USB Human Interface Device. Click Next.
6 The Wizard prompts you to search for the best driver for your device or select the driver you want from a displayed list.
Select Search for the best driver for your device. Click Next.
2
7 Windows now searches for new drivers in a specific location. Uncheck all the boxes. Click Next.
8 The Wizard indicates that it is ready to install the best driver for this device. Click Next to install the driver.
Click Finish when the Wizard is complete.
Add New Hardware Wizard –USB Audio Device
9 Next, the Wizard automatically installs the USB Audio Device. The Add New Hardware Wizard indicates that it has found
the USB Audio Device. Click Next.
10 The Wizard prompts you to search for the best driver for your device or select the driver you want from a list. Select
Search for the best driver for your device. Click Next.
11 Windows searches for new drivers in a specific location. Uncheck all the boxes. Click Next.
12 The Wizard indicates that it is ready to install the best driver for this device. Click Next to install the driver.
Click Finish when the Wizard is complete.
If the Wizard cannot locate the driver
If the Add New Hardware Wizard cannot locate the driver, insert your Windows Operating System CD-ROM into the CD-ROM
drive. Once inserted, press Back, and check the box for your CD-ROM drive (usually D). Click Next. Click Finish when the
Wizard is complete.
Note: Do not unplug the USB connector from the computer while an application that uses USB is running. This could cause a
system crash.
Headsets
The GN 8110 USB is designed to work with GN Netcom professional headsets equipped with a Quick Disconnect (QD) which
mates to the Quick Disconnect jack on the device. Disconnecting at the Quick Disconnect allows you to walk away from your
computer without removing your headset.
13 Before using your headset, join the Quick Disconnect to the mating connector on the GN 8110 USB.
Testing
14 To test that the speaker volume in your headset is working and set at a comfortable level, click once on the speaker
icon in the system tray. Click on the volume adjustment slider for a system sound. Adjust the volume to a level that is
comfortable for you. The Multimedia Properties window allows you to make advanced adjustments; go to the Volume
Controls section of this manual.
To test the microphone, use the sound recording utility that comes with Windows.
Go to Start/Programs/Accessories/Entertainment/Sound Recorder.
15 Position the microphone approximately one finger width away from your lower lip.
16 Click the red Record button and record a voice file. Click the Stop button when you are done. Replay the file by clicking
the Play button. If you hear your voice, recording is successful and the microphone is working properly.
If you cannot hear your voice, go to the Frequently Asked Questions section of this manual.
Warning! Although GN Netcom professional headsets have built-in hearing protection, computers are capable of generating
extremely loud sound bursts such as modem connections. Always check the volume level before putting on the headset.
Volume Controls
17 The volume for both the speaker and microphone are controlled by software. Go to Start/Settings/Control Panel to access
the Control Panel window. Double click on the Multimedia icon to bring up the Multimedia Properties window.
3