Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for SNAP SAM 9-10000
- Page 1 ® Model 9-10000 Patient Testing Instructions...
- Page 2 Copyright ©2024 SNAP Diagnostics, LLC All Rights Reserved. This booklet or any portion thereof may not be reproduced in any manner without the express written permission of the publisher. Snap Diagnostics 616 Atrium Drive, Ste 100 Vernon Hills, IL, 60061 Customer Support: 847-777-0000 https://snapdiagnostics.com...
- Page 3 Warnings • Snap Diagnostics Sleep Apnea Monitor is not intended to continuously display SpO2 and pulse rate in real time like a standard pulse oximeter routinely used in the operating room, in the intensive care unit, or during emergency transport (and therefore is not intended to trigger the initiation of oxygen therapy following detected desaturation).
- Page 4 Warnings (continued) • Do not use this device in the presence of magnetic resonance imaging (MR or MRI) equipment or in the presence of computer tomography (CT) equipment. • Do not use this device in the presence of flammable anesthetics. •...
- Page 5 (parent or guardian) or health care practitioner trained in the use of the SAM Model 9-10000. • Use only Snap Diagnostics supplied sensors and cables with this device. Using other accessories may result in increased electromagnetic emission or decreased electromagnetic immunity of the equipment.
- Page 6 The Snap Diagnostics SAM Model 9-10000 is not intended as a substitute for full polysomnography when additional parameters such as sleep stages or EEG activity are required.
- Page 7 Introduction This booklet provides instructions for taking your Snap Diagnostics home sleep test with the SAM Model 9-10000 device. These instructions may refer to the SAM Model 9-10000 as “SAM”. The testing equipment will be applied as instructed below, prior to the start of recording.
- Page 8 Snap Testing Kit To complete your sleep test, the following equipment will be used: Snap Sleep Apnea Monitor (SAM) + Belt Airflow Sensor + Nasal Cannula Oximetry Watch Monitor + Ring Sensor...
- Page 9 Connection Locations A – Oximeter Monitor Connection B – Airflow Sensor (microphone) to SAM Connection C – Airflow Sensor (microphone) to Cannula Connection D – Elastic Band Connection (band not shown below)
- Page 10 (Sleep Apnea Monitor)
- Page 11 Connect to the SAM + Belt Fasten the Belt around your upper chest, over your bed clothes, placing the Step 1: Sleep Apnea Monitor (SAM) in front. The belt size can be adjusted. It should fit snug and not cause a restriction in breathing. The SAM should be placed on your chest with the airflow sensor connection facing down.
- Page 12 Connect to the Airflow Sensor + Nasal Cannula Place the nasal cannula underneath your nose with the shorter pair of prongs Step 2: resting under your nostrils and the longer pair of prongs pointing down toward your mouth. The elastic headband fits over the ears. You can pull on the ends of the band to adjust the cannula for a comfortable fit.
- Page 13 If you experience any irritation, discontinue use and call Snap at (847) 777-0000 for assistance.
- Page 14 Once you have comfortably applied the monitors and sensors, you can turn them on to begin recording.
- Page 15 Start Recording Turn on the SAM Recorder. Press the power/record button to turn on Step 5: the SAM recorder and start the recording. The light above the battery symbol will illuminate. Turn on the Oximetry Watch Monitor. Press the power button on the side of Step 6: the watch to turn it on.
- Page 16 5 seconds. The device will record for 6 hours and automatically turn off. If the lights display magenta or amber, refer to the table on page 16 for troubleshooting contact Snap Customer Support at (847) 777-0000.
- Page 17 A fully charged battery, indicated by a green light, can record 3 nights of sleep. A half full battery, indicated by an amber light, can record a full night of sleep. A magenta light indicates that the battery must be charged before use. If you have insufficient battery, please call Snap Support (847) 777-0000.
- Page 18 This will illuminate the sensor lights for 5 seconds. Do not double press the power button as this will stop the recording. If the battery or power/record light displays a constant magenta color, contact Snap Customer Support at (847) 777-0000.
- Page 19 LED Color Green Amber Magenta Blue Meaning (Working) (Alert) (Fail) (BLE) Full 1-Night Charge No Charge, Battery Charge Available Call Snap Power/ Disconnected Errors Present, Startup Mode Record Record Sensor Call Snap (Flashing) Bluetooth Pulse Sensor Not Connected Oximeter Detected...
- Page 20 Once you have completed the test, return the test for analysis with all parts provided. Follow the instructions provided when you received it: • If the test kit was sent directly to you from Snap, return it to Snap following the shipping instructions provided in the box or on our website: https://snapdiagnostics.com/return-instructions...
- Page 21 To read your privacy rights under the Health Insurance Portability and Accountability Act (HIPAA), please visit: https://snapdiagnostics.com/privacy Snap Diagnostics is approved as an Independent Diagnostic Testing Facility (IDTF). To read about Medicare’s IDTF Performance Standards, please visit: https://snapdiagnostics.com/idtf-performance-standards...
- Page 22 Symbol Table Symbol Definition Type BF Applied Part applies to entire SAM Device Manufacturer Protected against spraying water and against access to hazardous parts with a tool, per IEC 60529. Caution Serial Number Keep Away from Rain Consult Instructions for Use Prescription Use Only Date of Manufacture Device shall have a shipping/storage temperature range of -25 to +70ºC...
- Page 23 This product implements Bluetooth wireless communication. Only manufacturer- supplied Bluetooth accessories should be connected to the product. If you experience difficulty in making or maintaining a Bluetooth connection, please contact Snap Customer Support at (847) 777-0000. Do not connect the product’s USB port to any computer, charger, or accessory other...
- Page 24 FCC Compliance Statement FCC ID: 2BDPB910000 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 25 Good Night! Snap Diagnostics 616 Atrium Drive, Ste 100 Vernon Hills, IL, 60061 Customer Support: 847-777-0000 https://snapdiagnostics.com 726-784636 Rev D...
Need help?
Do you have a question about the SAM 9-10000 and is the answer not in the manual?
Questions and answers