Summary of Contents for Phoenix Contact WF 1000
- Page 1 Stripping machine with integrated graphic display, for conductors and cables up to 6 mm in diameter Original operating instructions...
- Page 3 6 mm in diameter UM EN WF 1000, Revision 03 2023-11-24 This manual is valid for: Designation Item No. WF 1000 1212149 WF 1000 120V 1212258 Phoenix Contact GmbH & Co. KG • Flachsmarktstraße 8 • 32825 Blomberg • Germany phoenixcontact.com...
- Page 4 Disposal ........................6 Description of the WF 1000 ......................7 Scope of supply .......................7 Overview of the operating components..............8 Setting up and operating the WF 1000 ..................9 Setting up the WF 1000 ..................9 Stripping ....................... 11 Maintenance and decommissioning ..............11 Troubleshooting ........................12 Cable not clamped ....................
- Page 5 This user manual is addressed to persons who are familiar with the relevant safety con- cepts for handling electrical machines. The persons must be able to recognize dangers. The WF 1000 may only be started up, operated and maintained by trained personnel, who strictly observe the instructions in this user manual.
- Page 6 Only use original replacement parts from Phoenix Contact. Unauthorized conversions that exceed the scope of modification, and changes to the WF 1000 are not permitted for safety reasons. Use the WF 1000 in a perfectly safe tech- nical condition only.
- Page 7 Description of the WF 1000 Description of the WF 1000 Scope of supply Figure 2-1 Scope of supply Basic device WF 1000 Receptacle tray (protective hood) Cable centering aid Power cable Phoenix Contact 7 / 20 103896_en_03...
- Page 8 WF 1000 Overview of the operating components Figure 2-2 Operating components Handle Button, for resetting the counter and acknowledging messages or inputs Motor axis, manual operation Mains connection Mains fuses, (see page Mains switch, the LC display lights up when switched on Removal length knob, for setting the length to be removed.
- Page 9 • Determine the diameter of the conductors (in mm). To ensure that the WF 1000 does not cut into the conduc- tor, add a safety margin of 0.4 mm. Example: measured diameter 0.8 mm + 0.4 mm = 1.20 mm •...
- Page 10 WF 1000 Correcting the diameter To prevent damaging the conductor, the cut must stop 0.1 to 0.3 mm from the conductor. • Check the cutting depth with a test cut and correct the setting, if necessary. 0.1 mm ... 0.3 mm The blades have a sufficient safety margin to the conduc- tor and cleanly cut through the insulation.
- Page 11 Press the button on the rear of the device to set the counter to zero. Shutting down • Switch off the WF 1000 with the mains switch (A). • Disconnect the mains plug from the device (B). Phoenix Contact 11 / 20...
- Page 12 The button must be pressed. • Press the reset button. WARNING: Risk of injury The WF 1000 starts by moving to its initial position. The sensor for the start button does not • Disconnect the WF 1000 from the power source.
- Page 13 The blades must snap back smoothly. • If the blades cannot be pushed back smoothly, dismantle the blades using the same procedure as for blade replacement (see page 14). • Remove any remaining insulation from the stripping area. Phoenix Contact 13 / 20 103896_en_03...
- Page 14 WF 1000 Replacing the blades and clamping jaws Shutting down • Switch off the WF 1000 with the mains switch (A). • Disconnect the mains plug from the device (B). Replacing the blades WARNING: Risk of injury The blades are sharp. Make sure not to touch the cut- ting edge.
- Page 15 Troubleshooting Replacing the start button Shutting down • Switch off the WF 1000 with the mains switch (A). • Disconnect the mains plug from the device (B). Replacing the start button • Replace a defective start button (for ordering data, see page 16).
- Page 16 WF 1000/TR 1212416 Receptacle tray WF 1000/COV 1212417 Cable centering aid On request Mains fuse for WF 1000 FUSE SB 1,25 A 1208801 Mains fuse for WF 1000 120V FUSE SB 2,5 A 1209062 16 / 20 Phoenix Contact 103896_en_03...
- Page 17 EU declaration of conformity EU declaration of conformity EU Declaration of Conformity No. 000490338_03_DoC_EU Phoenix Contact GmbH & Co.KG Manufacturer: Address: Flachsmarktstraße 8, 32825 Blomberg, Germany WF 1000 Product designation: Order No.: 1212149 This declaration of conformity is issued under the sole responsibility of the manufacturer. The products specified in this...
- Page 18 WF 1000 UK declaration of conformity UK Declaration of Conformity No. 097137283_00_DoC_UK Manufacturer: Phoenix Contact GmbH & Co. KG Address: Flachsmarktstraße 8, 32825 Blomberg, Germany Product designation: WF 1000 Order No.: 1212149 This declaration of conformity is issued under the sole responsibility of the manufacturer. The product(s) specified in this declaration are in conformity with the following relevant legislation: S.I.
- Page 19 The receipt of technical documentation (in particular user documentation) does not con- stitute any further duty on the part of Phoenix Contact to furnish information on modifi- cations to products and/or technical documentation. You are responsible to verify the suitability and intended use of the products in your specific application, in particular with regard to observing the applicable standards and regulations.
- Page 20 Should you have any suggestions or recommendations for improvement of the contents and layout of our manuals, please send your comments to: tecdoc@phoenixcontact.com 20 / 20 Phoenix Contact GmbH & Co. KG • Flachsmarktstraße 8 • 32825 Blomberg • Germany phoenixcontact.com...
- Page 22 Phoenix Contact GmbH & Co. KG Flachsmarktstraße 8 32825 Blomberg, Germany Phone: +49 5235 3-00 Fax: +49 5235 3-41200 Email: info@phoenixcontact.com phoenixcontact.com...
Need help?
Do you have a question about the WF 1000 and is the answer not in the manual?
Questions and answers