Advertisement
Quick Links
Advertisement
Related Manuals for 2N 914422E
Summary of Contents for 2N 914422E
- Page 1 Installation manual 2N® SIP Speaker Horn v.2.11 www.2n.com...
- Page 2 Installation manual 2N® SIP Speaker Horn Content: • 1. Product Overview • 1.1 Components and Associated Products • 1.2 Terms and Symbols • 2. Description and Installation • 2.1 Before You Start • 2.2 Mechanical Installation • 2.3 Electric Installation •...
- Page 3 VMS phone systems via IP (VoIP PBX). Thanks to PoE, ® they can be connected to IP with a single network cable. 2N SIP Speaker Horn can be used for live paging or playing scheduled or pre-startable messages. It is equipped with an automatic audiotesting function, which can check the speakers for proper functions.
- Page 4 Installation manual 2N® SIP Speaker Horn • Streamed audio support • Applicable as standard VoIP telephone/communicator • DTMF detection according to RFC2833, in-band and SIP-INFO Basic Features • 10/100Base-TX LAN interface • 24 V DC / 2 A or PoE 802.3af supply •...
- Page 5 Installation manual 2N® SIP Speaker Horn Power Supply Part Numbers: • PoE injector – without cable • PoE injector – with EU cable 91378100, 01394-001 • PoE injector – with US cable 91378100E • For power supply of intercom via ethernet cable when PoE switch is not available.
- Page 6 Installation manual 2N® SIP Speaker Horn 2N Part No. 91378358 • Grandstream GXV3275 VoIP telephone • GXV3275 is the successor to the popular GXV3175 Axis Part No. 01421-001 model, which allows comfortable video calls in the IP network. Touchscreen control. Accessories Part No.
- Page 7 (2 wires) from your original door bell or door intercom to connect any IP device. You don’t have to ® configure anything, and you only need one 2N 2Wire unit at each end of the cable and a power source connected to at least one of these units.
- Page 8 Installation manual 2N® SIP Speaker Horn Caution • Important information for system functionality. • Useful information for quick and efficient functionality. Note • Routines or advice for efficient use of the device. 8 / 29...
- Page 9 Installation manual 2N® SIP Speaker Horn 2. Description and Installation ® In this section, we describe the 2N SIP Speaker, Wall Mounted product and its installation. Here is what you can find in this section: • 2.1 Before You Start • 2.2 Mechanical Installation •...
- Page 10 Installation manual 2N® SIP Speaker Horn Speaker Holder Warning • To ensure the IP cover class, tighten the screws between the body and the wave guide with a torque of 0.85 Nm. Using a higher value may lead to cracks in the screw joints.
- Page 11 Connect a 24 V power supply (unless PoE is used). Caution • Be sure to connect the 2N SIP Speaker Horn power supply as the last step. The same applies to PoE supply from the LAN. • The device must be part of the electrical system of the building.
- Page 12 Symmetrical microphone Microphone connection LAN Connection 2N SIP Speaker Horn can be connected to a standard local area network using a LAN interface via the RJ-45 connector on the back panel. Always use CAT-5d or higher class cables for reliability reasons. 12 / 29...
- Page 13 We recommend the use of a shielded SSTP Ethernet cable. Power Supply Connection 2N SIP Speaker Horn can be fed using active network elements or PoE injectors via the LAN interface. In case this option is unavailable, use a 24 V DC / 2 A (Part No. 914423E) power supply or another power supply on condition that you keep the nominal values included in the Mechanical and Electrical Parameters subsection.
- Page 14 Warning • 2N SIP Speaker Horn cannot be fed from an external power supply and PoE at the same time. A combined supply might result in a device damage. • If you use an adapter other than the recommended one, do not exceed the nominal supply voltage value of 24 V.
- Page 15 SIP-based systems. ® Use an integrated web interface for 2N SIP Speaker Horn configuration. ® ® Apply the 2N Helios IP Network Scanner to search all the 2N SIP Speaker Horn units connected. ® SIP Speaker Horn connection panel ® SIP Speaker Horn back panel Connectors and Controls: •...
- Page 16 ® Description of 2N Network Scanner ® The purpose of this application is to find the dynamic IP address of 2N SIP Speaker Horn in the local IP network. The application can be downloaded from the 2N web sites www.2n.cz. ® Run the 2N Network Scanner installer.
- Page 17 SIP Speaker Horn and start configuring as described in the Login subsection below. Login ® In the web browser enter the IP address of 2N SIP Speaker Horn. Subsequently, a login screen will be displayed. The default login username and password are as follows: •...
- Page 18 In some cases, it may be useful to reset the 2N SIP Speaker Horn factory default values using ® the RESET switch on the back panel. Do so, for example, if 2N SIP Speaker Horn ceases to respond due to, for example, incorrect LAN settings, LAN configuration changes, forgotten password and so on.
- Page 19 Note • The delay after pressing RESET till the first light and sound signalling is set to 15– 35 s depending on the 2N IP intercom/answering unit model used. ® • 11 s is the valid value for 2N SIP Speaker Horn.
- Page 20 Installation manual 2N® SIP Speaker Horn • Wait until the red LED goes off and the acoustic signal can be heard (approx. for another 3 s). • Wait until the green LED goes off and the red LED goes on again and the acoustic signal ...
- Page 21 Installation manual 2N® SIP Speaker Horn Caution • In case of resetting the factory default settings on a device with a version of firmware 2.18 or higher it is necessary to reprogram the ® Security Relay using the instructions from section 2.4.
- Page 22 (reception desk or user mobile phones). Refer to the Scheduler subsection for deactivation code settings (Configuration Manual). Call prolongation confirmation signalling ® The maximum call duration is set in 2N SIP Speaker Horn for security reasons; refer to Miscellaneous subsection (Configuration Manual). 22 / 29...
- Page 23 Meaning Internal application launched ® ® Upon 2N SIP Speaker Horn power up or restart, the 2N SIP Speaker Horn internal application is launched. A successful launch is signalled by this tone combination. Connected to LAN, IP address received ®...
- Page 24 Tones Meaning Call end advance signalling ® You can set a call time limit in 2N SIP Speaker Horn to avoid call blocking. Push a button on your VoIP telephone to prolong the call. ® Connected call when calling from a telephone to 2N SIP Speaker...
- Page 25 Installation manual 2N® SIP Speaker Horn 4. Technical Parameters Mechanical and Electrical Parameters • Dimensions: diameter 237 mm, length 309.6 mm • Weight: 2.3 kg • Color: grey • Operating temperature: −30 ˚C – +60 ˚C • Protection: IP67 • Installation: U-type holder made of stainless steel •...
- Page 26 • 5.2 Directives, Laws and Regulations • 5.3 General Instructions and Cautions 5.1 Troubleshooting For the most frequently asked questions refer to faq.2n.cz. 5.2 Directives, Laws and Regulations ® SIP Speaker Horn conforms to the following directives and regulations: •...
- Page 27 Installation manual 2N® SIP Speaker Horn Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. ® SIP Speaker Horn conforms to the ČSN EN 60529:1993+A1:2001+A2:2014 Standard. Rating: IP67. ...
- Page 28 Installation manual 2N® SIP Speaker Horn The consumer shall, without delay, change the access password for the product after installation. The manufacturer shall not be held liable or responsible for any damage incurred by the consumer in connection with the use of the original password.
- Page 29 Instalační manuál 2N® SIP Speaker Horn 29 / 29...
Need help?
Do you have a question about the 914422E and is the answer not in the manual?
Questions and answers