Download Print this page

Advertisement

Quick Links

360 Deep Wall Installation Guide
Edition 2
September 2024

Advertisement

loading
Need help?

Need help?

Do you have a question about the 360 Deep Wall and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Laminex 360 Deep Wall

  • Page 1 360 Deep Wall Installation Guide Edition 2 September 2024...
  • Page 3 To the extent permitted by law, Laminex disclaims all liability (including liability for negligence) for all loss, damage, liability or claim resulting from the use of the information provided in this document.
  • Page 4 Contents Possible tools required ..........page 5 Best practices .
  • Page 5 Possible tools required (not supplied) 2.5mm 35mm...
  • Page 6 Best practices Check all packages on delivery. Don’t store in extreme conditions. Store packages flat. Don’t use sharp objects when opening packages. Re-cycle packaging.
  • Page 7 Planning dimensions 460mm 360mm 585mm 625mm 625mm 585mm 585mm 40mm 40mm Mid-height wall cabinet Wall cabinet Tall cabinet Appliance, (illustrated) Base cabinet Base cabinet Pantry...
  • Page 8 Start in a corner - Blind corner base - 400 Door / 450 Door / 500 Door Corner planning (LH illustrated, RH opposite) m 6 5 m m 6 5 m 650 mm 650 mm 150mm 100mm 1000 Blind Corner Base 1000 Blind Corner Base 500 Door 450 Door...
  • Page 9 Start in a corner - Blind corner base - 400 Door / 450 Door / 500 Door Attach centre upright (LH, 500 opening illustrated)
  • Page 10 Start in a corner - Blind corner base - 400 Door / 450 Door / 500 Door Prepare and fit fillet (LH, 500 opening illustrated) 4x30mm CSK 500 Door = 500mm 450 Door = 450mm 400 Door = 400mm 4x30mm CSK...
  • Page 11 Start in a corner - Blind corner base - 400 Door / 450 Door / 500 Door Attach blanking panel and spacer (LH, 500 opening illustrated) 500mm door 450mm door 400mm door x6-8 45mm KD screw (not supplied) Connect cabinets (LH, 500 opening illustrated) 45mm KD screw (not supplied)
  • Page 12 Start in a corner - 1000 L Shaped corner base cabinet Fittings Fittings For ease of assembly loosen screws x6. DO NOT remove completely. Re-tighten screws x6.
  • Page 13 Start in a corner - 1000 L Shaped corner base cabinet Screw the legs all the way in before turning cabinet upright. Adjust legs 150mm...
  • Page 14 Start in a corner - Wall cabinet planning Corner planning (LH illustrated, RH opposite) m 4 0 m m 4 0 m 400mm 700mm 20mm 700 Corner Wall Cabinet 700 L Shaped Corner Wall Start in a corner - Wall cabinet 2 filler strips supplied, taped to centre upright Flip the cabinet for LH/RH corner installations...
  • Page 15 Start in a corner - Wall cabinet Attach fillet to cabinet 300mm 4x30mm CSK Connect cabinets 45mm KD screw (not supplied)
  • Page 16 Start in a corner - 700 L Shaped corner wall cabinet...
  • Page 17 1000/700 L Shaped corner base and wall cabinet - Bi-fold doors 1000 L shaped illustrated, 700 L shaped similar 165° hinge 3.5x13mm CSK Concealed hinge Left hand opening illustrated, right hand opposite 3.5x13mm CSK Bi-fold door to cabinet CLICK hinge plates Bi-fold door Cabinet 32mm...
  • Page 18 700 L Shaped corner wall cabinet - Doors + fillet Attach fillet and hinges 700 L Shaped corner wall 38mm 297mm 3.5x16mm CSK 165° hinge Fit hinge plate and door to cabinet and adjust CLICK Door up/down Door left/right Door in/out...
  • Page 19 Appliance tower Appliance tower options available See following pages for detailed instructions. Single oven Single oven + 2 drawers Single oven x2 Double oven + drawer Single oven / Microwave Single oven / Microwave + drawer Fridge - Freezer...
  • Page 20 Appliance tower - Configurations Single oven Add support brackets x4. Fix hinge plates, (RH door opening shown). Position mid shelves dependant upon your requirement. Single oven + 2 drawers Add support brackets x4. Fix hinge plates, (RH door opening shown). Add drawer runners x4, (Drawer pack supplied separately).
  • Page 21 Appliance tower - Configurations Double Oven Add support brackets x4. Fix hinge plates, (RH door opening shown). Position mid shelves dependant upon your requirement. Single oven x2 + drawer Add support brackets x8. Fix hinge plates, (RH door opening shown). Add drawer runners x2, (Drawer pack supplied separately).
  • Page 22 Appliance tower - Configurations Single oven / Microwave Add support brackets x8. Fix hinge plates, (RH door opening shown). Position mid shelf dependant upon your requirement. Single oven / Microwave + drawer Add support brackets x8. Fix hinge plates, (RH door opening shown). Add drawer runners x2, (Drawer pack supplied separately).
  • Page 23 Appliance tower - Filler strip Single oven x2 Fixing screws not included Single oven / Microwave Fixing screws not included...
  • Page 24 Appliance tower - Adapt supplied cabinet to suit a Tall Fridge/Freezer Back panel removal Retain screws for future use Shelf removal Single oven cabinet illustrated, others cabinets similar Reposition top shelf...
  • Page 25 Appliance tower - Adapt cabinet to suit the Fridge/Freezer Measure new shelf position and trim back panel Measure from top Replace back panel and secure to new shelf position Secure using retained screws Fridge/Freezer Fix hinge plates, (RH door opening shown).
  • Page 26 Appliance tower - Configurations Attach legs Single oven cabinet illustrated, others cabinets similar Screw the legs all the way in before turning cabinet upright. Adjust legs 150mm...
  • Page 27 600 Oven base cabinet Remove shelf retainer’s Remove shelf Attach clips to the 3.5x12mm PH underside of shelf Replace shelf...
  • Page 28 600 Oven base cabinet Pre-fabricated 58mm filler panels TOP FILLER 56.5mm 56.5mm BOTTOM FILLER 597mm x 58mm x2 filler panels 3.5x20mm CSK NOTE: If a 58mm filler has been supplied then the following procedures are not necessary. Prepare filler panels using a 176mm drawer front, when supplied From a 176mm drawer front trim 2 filler panels, edge raw surfaces.
  • Page 29 600 Oven base cabinet Fit top and bottom filler panels Fit top filler Drill 5mm through top rail x2 4x30mm CSK Fit bottom filler...
  • Page 30 900 Oven base cabinet Remove shelf retainer’s Remove shelf Attach clips to the 3.5x12mm PH underside of shelf Replace shelf...
  • Page 31 900 Oven base cabinet 58mm filler panels TOP FILLER BOTTOM FILLER 56.5mm 56.5mm 897mm x 58mm x2 filler panels NOTE: If a 58mm filler has been supplied then the 3.5x20mm CSK following procedure is not necessary. From 2, 115mm filler panels trim 2, 58mm filler panels, edge all raw surfaces.
  • Page 32 900 Oven base cabinet - 480 Oven option Remove shelf retainer’s Remove shelf Remove Keep in a safe place 3.5x12mm PH...
  • Page 33 900 Oven base cabinet - 480 Oven option Replace in upper position 3.5x12mm PH 115mm filler panel TOP FILLER 897mm x 115mm filler panel Drill 5mm through top rail x3 4x30mm CSK...
  • Page 34 900 Oven base cabinet - 480 Oven option 21mm 21mm BOTTOM FILLER 897mm x 115mm filler panel 3.5x20mm CSK 41.5mm 32mm 3.5x12mm PH Replace shelf...
  • Page 35 Sink base cabinet - Door / Deep drawer 600 / 800 / 900 / 1000 door and drawer options 1 door 2 door Door option (600 illustrated, 800, 900 and 1000 similar) x2/4 x2/4 x4/8 3.5x13mm CSK Right hand opening illustrated, left hand opposite CLICK Deep drawer option...
  • Page 36 800/1000 Pantry...
  • Page 37 1000/1200 Corner pantry - Preparation 90° 464mm 500mm opening 564mm 600mm opening 4x30mm CSK...
  • Page 38 1000/1200 Corner pantry with return base and wall cabinet 1000 Corner planning 1200 Corner planning (LH illustrated, RH opposite) (LH illustrated, RH opposite) 641mm 641mm 38mm 38mm Wall Wall cabinet cabinet Base Base cabinet cabinet Out of a standard decor panel cut: A 641 x 2129mm B 38 x 720mm C 38 x 720mm...
  • Page 39 1000/1200 Corner pantry with return tower cabinet 1000 Corner planning 1200 Corner planning (LH illustrated, RH opposite) (LH illustrated, RH opposite) 641mm 641mm 38mm 38mm Tower Tower cabinet cabinet 3 8 m 5 6 m 1000/1200 blanking panel, fix by 9 screws 1000 fixing 1200 fixing Pantry...
  • Page 40 1000/1200 Corner pantry - Attach doors Fit 110° hinges 3.5x13mm CSK CLICK...
  • Page 41 800/1000 Pantry - Internal drawer option (4+1) 5 Drawer runner positions Drill runner positions x30, (5 x 12mm deep). Add drawer runners x10, (Drawer pack supplied separately). Fix hinge plates, Use 165° hinges for this installation. 12mm Deep drawer Standard drawer Deep drawer Deep drawer Deep drawer...
  • Page 42 800/1000 Pantry - Internal drawer option (2+1) 3 Drawer runner positions Drill runner positions x18, (5 x 12mm deep). Add drawer runners x6, (Drawer pack supplied separately). Fix hinge plates, Use 165° hinges for this installation. 12mm Standard drawer Deep drawer Deep drawer 37mm 69mm...
  • Page 43 Height adjustment - Base and tower cabinets, (generic) Optimum height 150mm -10mm +30mm x2-5...
  • Page 44 Fix base cabinets to wall Ensure cabinet is level -10mm +30mm 3.5x12mm PH Use appropriate wall fixings for type of wall, (fixings not supplied). 3.5x12mm PH...
  • Page 45 Fix tall cabinets to wall Ensure cabinet is level -10mm +30mm 3.5x12mm PH Use appropriate wall fixings for 3.5x12mm PH type of wall, (fixings not supplied).
  • Page 46 Fix wall cabinets to wall Ensure cabinet is level Use appropriate wall fixings for type of wall, (fixings not supplied). Align top of wall cabinet with the top of an appliance tower/pantry If no appliance tower/pantry is used measure 2280mm from floor.
  • Page 47 500 and 600 Pantry - Internal drawer option (4+1) 5 Drawer runner positions Drill runner positions x30, (5 x 12mm deep). Add drawer runners x10, (Drawer pack supplied separately). Fix hinge plates, (RH door opening shown). Use 165° hinges for this installation. 12mm Deep drawer Standard drawer...
  • Page 48 500 and 600 Pantry - Internal drawer option (2+1) 3 Drawer runner positions Drill runner positions x18, (5 x 12mm deep). Add drawer runners x6, (Drawer pack supplied separately). Fix hinge plates, (RH door opening shown). Use 165° hinges for this installation. 12mm Standard drawer Deep drawer...
  • Page 49 Internal drawer assembly - (deep drawer illustrated, standard drawer similar) Fix connector brackets to drawer back Standard drawer Add drawer sides Locate and secure drawer base panel...
  • Page 50 Internal drawer assembly - (deep drawer illustrated, standard drawer similar) Attach drawer front Attach side rails - deep drawer only Drawer adjustment Vertical adjustment Horizontal adjustment Frontal alignment...
  • Page 51 Internal drawer removal Frontal removal Drawer removal...
  • Page 52 Base drawer frontals Prepare standard drawer frontal 3.5x25mm CSK Per frontal Prepare deep drawer frontal Use for a 176mm drawer back. Use for a 144mm drawer back. 3.5x16mm CSK 3.5x25mm CSK Per frontal Attach a frontal CLICK...
  • Page 53 Base drawer frontals Attach deep drawer side rails Remove a side rail Remove a frontal...
  • Page 54 Base drawer frontals Drawer removal Drawer adjustment Vertical adjustment Horizontal adjustment Deep drawer frontal...
  • Page 55 Fit door hinges and adjustment Fit hinge plates Fit hinges to door Right hand opening illustrated, left hand opposite Fit door 3.5x13mm CSK CLICK Adjustment Door up/down Door left/right Door in/out Door jointing plates - Tower cabinet Slab door J Pull door 3.5x13mm CSK 3.5x13mm CSK...
  • Page 56 Kick boards Attach front kick board Mark the position of legs and the centre line of kick board. Attach return kick board Mark the return position of legs and the centre line of kick board.
  • Page 57 Kick boards Internal corners Run one section of the plinth through the corner. With plinth against feet mark vertical line. ‘Y’mm ‘X’mm Fix against marked line. 3.5x12mm PH 14mm ‘X’mm ‘Y’mm 3.5x12mm PH Fix central on marked line.
  • Page 58 Notes...
  • Page 59 Notes...