Related Manuals for ROBO-TEK ROBO-CHARGE
Summary of Contents for ROBO-TEK ROBO-CHARGE
- Page 1 User Manual Please read this manual carefully before using the product and store the manual properly.
- Page 2 Contents 1.WARNINGS 2.Packing List 3.Product Overview 4.Instructions for Use 5.Daily Maintenance 6.Off-season Storage 7.Parts Replacement 8 FAQs 9.Compliance Statement...
- Page 3 1. WARNINGS they have been given supervision or instruction for using the robot by a person Thank you for purchasing Robo-Charge Robotic Pool Cleaner. responsible for their safety. Please read this manual carefully before using the product for the first time and keep this manual for future reference.
- Page 4 • The charging position of the product should be at least 3 meters away from the • This product contains a Lithium battery. Do not disassemble the motor edge of the pool. box to replace the battery. When the battery life ends, Contact ROBO- TEK to have the battery replaced by qualified personnel.
- Page 5 Applicable pool size swimming pool of 1,076 square feet (100 square meters) 2. Packing List Pool depth 0.5-2.5 m (1.64-8.2 ft) Robot dimensions 475 × 395 × 250 mm/18.7 × 15.6 × 9.8 inches Robot weight 9 kg/19.8 lbs Charger input 100-240 V~50/60 Hz Charger output 29.2 V 3 A (US: 29.4 V 3 A)
- Page 6 4. Instructions for Use Charging Please fully charge the robot before using it for the • first time. Remove the robot from the pool and turn it off. • Make sure that the charging port is dry. •...
- Page 7 Power and status indicators LED Color Status Green Sufficient battery Blue Insufficient battery Orange Very low battery Fault L OOR Cleaning Modes ( OFF AUTO FLOOR WALL) owly put the robot into the water. Then, the robot will release the air in the body and sink to the bottom of the pool.
- Page 8 Placing the robot into the wate Select the desired cleaning mode, and place the robot in the water as soon as possible. The robot will start working within 10 seconds after reaching the bottom of the pool.
- Page 9 Taking out of the swimming pool The robot will automatically stop at the bottom edge of the swimming pool after the cleaning task is completed or when the battery power is low. Use a hook to lift it out of the pool.
- Page 10 5. Daily Maintenance For optimal product performance, follow these instructions to maintain the robot. Remove the robot from the pool and turn it off. LO OR Cleaning the filter basket We strongly advised cleaning the filter basket after each cleaning task. ①...
- Page 11 After daily use Clean the robot and filter basket after each cleaning. Open the filter basket cover and remove the debris. Rinse the filter basket. Note: Please clean the filter basket in time. A clogged filter can affect the overall cleaning performance of the robot, making it difficult to generate suction or trap dirt and debris in the filter basket.
- Page 12 Off-season Storage If the robot will not be used for a long time, perform the following storage steps: Thoroughly clean and dry the filter basket, roller brushes, and tracks. • Ensure that there is no residual water in the cleaner. •...
- Page 13 7. Parts Replacement Roller brush replacement. On the back of the roller brush belt, peel off the silicone buckles fixing the mounting grooves Remove all the silicone buckles, replace the roller brush belt with a new one, align the silicone buckles with the mounting grooves, and press the buckles to fix them in the grooves.
- Page 14 Remove the screw cover and unscrew the screws. Remove the side Clean the inside of the side panels...
- Page 15 8.FAQs Possible Causes Issue Solutions Check whether the power outlet is working. The power outlet has no power. Check the connection between the power cord The power cord is not properly and the power outlet. connected to the power outlet. The robot does not The connection between the power Check the connection between the robot and the adapter.
- Page 16 Check whether the robot works in floor Switch to wall cleaning mode. cleaning mode and cleans only the floor. Clean the filter basket. The filter basket is clogged. The robot does not climb walls. Check the levels of chemicals in the water. Poor water quality can allow algae to There is algae on the wall and the pH grow, making walls slippery.
- Page 17 • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult Robo-Tek for assistance service@robo-tek.com.au...
Need help?
Do you have a question about the ROBO-CHARGE and is the answer not in the manual?
Questions and answers