Advertisement
Quick Links
Advertisement
Summary of Contents for HOLZCRAFT HBS 533 S
- Page 1 Instruction Manual Wood band saw HBS 533 S HBS 633 S HBS 533 S...
- Page 2 Product identification 1.2 Customer service..........3 1.3 Disclaimer ............3 Wood band saw Item number 2 Safety ............3 HBS 533 S 5155313 2.1 Legend of symbols..........3 HBS 633 S 5156303 2.2 Operator responsibility........4 2.3 Personnel requirements........5 2.4 Personal protective equipment ......
- Page 3 Introduction Introduction Please submit any information and experiences you make during application of the machine as these may be valuable for product improvements. You have made an excellent choice in purchasing a HOLZKRAFT Wood band saw. 1.3 Disclaimer Carefully read the operating instructions prior to commissioning.
- Page 4 Safety Operator's duties If the wood band saw is used for commercial purposes, the operator of the wood band saw is subject to the legal DANGER stipulations in terms of occupational safety. For this rea- This combination of symbol and signal term indi- son, the safety instructions in these operating instruc- cates a directly dangerous situation which may tions as well as the safety, accident prevention and envi-...
- Page 5 Safety 2.3 Personnel requirements 2.4 Personal protective equipment Personal protective equipment is intended to protect the Qualifications health and safety of persons at work. Staff must wear the personal protective equipment indicated in individual The different tasks described in these operating instruc- sections of these operating instructions when carrying tions require different levels of skills in terms of the quali- out the different tasks on the machine.
- Page 6 Safety 2.6 Safety instructions for operating - Observe all safety instructions and warnings on the machine and keep the labels in a legible state staff - Keep children and persons who are not familiar with the machine clear of your work environment, the machine and tools.
- Page 7 Intended use 2.7 Special safety instructions for 2.9 Safety labels on the wood band wood band saws The following safety identifications are attached to the - When sawing round timber, clamp the workpiece to wood band saw (Fig. 1) and must be observed. prevent it rotating.
- Page 8 Technical Data - Modifications to the machine or the use of modified tool systems. Type HBS 533 S HBS 633 S Misuse of the wood band saw can lead to dangerous situa- tions. Item number...
- Page 9 Description of the device 4.1 Type plate HBS 633 S Fig. 2: Type plate HBS 633 S Description of the device Figures in these operating instructions may deviate from the original. Fig. 3: Controls 5.1 Controls Mikroswitch Saw band height adjustment Saw band clamping head Saw band guide Rip fence protection rail...
- Page 10 Delivery, packaging and storage 5.2 Scope of delivery Saw bands HBS 533 S Length x Width x Item HBS 533 S / HBS 633 S Strength number - Band saw Wood 4190 x 10 x 0,5 mm 5160535 - Work table...
- Page 11 Assembly and setting up 6.3 Storage WARNING! Allow the wood band saw to fully cool down, and always The use of unstable lifting and load suspension store in a clean condition and a dry, clean and frost-free equipment that might break under load can cause environment.
- Page 12 Operation Machines with 400 V electric motor WARNING! Connecting the machine to the power supply: Danger! Failure to observe the following rules entails a risk of - make sure that the power supply has the same injury for the operator and other persons. characteristics (voltage, mains frequency, phase position) as the motor.
- Page 13 Operation 8.2 Settings NOTE! Before starting up, using, maintaining or intervening with the machine in any other way, always carefully read the operating and maintenance instructions. Only persons who are familiar with handling and the effect of the machine are permitted to handle and work on and with the machine.
- Page 14 Operation Step 3: Release the saw band clamp by actuating the quick clamping lever (2). Step 4: Carefully pull the used saw band off the rollers and guide it through the slot in the table. Step 5: Now place the new saw band on the two saw band rollers in reverse order and centre with re- spect to the rubbers supports.
- Page 15 Operation Step 2: The screw (4) for adjusting the saw band run is located at the rear centre of the machine. This button is used to adjust the run. The saw band run setting must be adjusted with the front panel open.
- Page 16 Operation 8.2.9 Extraction port 8.2.11 Use and assembly of the laser Mount the bracket (1) on the machine. For connection to an extraction system, your band saw is Insert the batteries into the laser, paying attention to the equipped with one or two extraction ports (2) with a di- correct polarity.
- Page 17 Operation For all cutting actions, move the upper band guide as In combination with an angled table, the operator can close as possible to the workpiece. This ensures the best thus perform double mitre cuts. Hold the workpiece firmly possible cut quality and operator safety. Always guide against the fence on the cross-cutting gauge and flat the workpiece with both hands and keep it flat on the against the table.
- Page 18 Maintenance and repairs Saw band parameters: 9.1 Cleaning Softwood, as- Hard- ATTENTION! pen, poplar wood Any chips that occur should be regularly removed Rake angle [°] 13 - 16 8 - 10 from the inside of the band saw. Before opening the Tooth height [mm] 5.5 - 6.5 5.5 - 6...
- Page 19 Troubleshooting 9.2 Care after finishing work 9.3 Maintenance and repairs Maintenance and repairs must be carried out by special- Always keep the wood band saw clean. ist staff only. If the wood band saw is not operating cor- rectly, contact a specialist retailer or our customer ser- vice.
- Page 20 Example Disposal of used electrical and electronic equipment The engine for the Wood Band Saw HBS 533 S must be (Applicable in the countries of the European Union and ordered. The engine has the number 23 in the spare other European countries with a separate collection sy- parts drawing 1.
- Page 21 The following drawings of the HBS S Series are intended to identify the required spare parts in the event of service. To or- der, send a copy of the parts drawing with the parts marked to your authorized dealer. Spare Parts Drawings HBS 533 S Spare parts drawing 1...
- Page 22 Spare parts Drawing to Drawing to Drawing to Drawing to Drawing to Drawing to HBS S-Series | Version 3.13...
- Page 23 Spare parts Spare parts drawing 2 Spare parts drawing 3 HBS S-Series | Version 3.13...
- Page 24 Spare parts Spare parts drawing 4 Spare parts drawing 5 HBS S-Series | Version 3.13...
- Page 25 Spare parts Spare Parts Drawings HBS 633 S Spare parts drawing 1 HBS S-Series | Version 3.13...
- Page 26 Spare parts Drawing to Drawing to Drawing to Drawing to Drawing to Drawing to HBS S-Series | Version 3.13...
- Page 27 Spare parts Spare parts drawing 2 HBS S-Series | Version 3.13...
- Page 28 Spare parts Spare parts drawing 3 Spare parts drawing 4 HBS S-Series | Version 3.13...
- Page 29 Electrical circuit diagram 13 Electrical circuit diagram Electro circuit diagram Model HBS 533 S and 633 S Fig. 17: Wiring Diagram Wood Band Saw HBS 533 S and 633 S HBS S-Series | Version 3.13...
- Page 30 ® Product group: Holzkraft Woodworking machines Machine type: Wood band saw Designation of the machine*: Item number*: HBS 533 S 5155313 HBS 633 S 5156303 Serial number*: ___________________ Year of manufacture*: 20____ * Fill in these fields according to the information on the type plate.
- Page 31 Notes 15 Notes HBS S-Series | Version 3.13...
- Page 32 www.holzkraft.de...
Need help?
Do you have a question about the HBS 533 S and is the answer not in the manual?
Questions and answers