Summary of Contents for Cold Point Adirondack Aire WM Series
- Page 1 WM series Water Source Replacement Unit INSTALLATION, OPERATION & MAINTENANCE MANUAL Cold Point Corporation, Rome, New York 13440 | Phone 315.339.2331 Fax 315.339.2358 | www.ColdPointCorp.com...
- Page 2 Only auxiliary electric heaters approved by Cold Point shall be Only auxiliary electric heaters approved by Cold Point shall be who meet local, state, and federal proficiency requirements.
- Page 3 Adirondack Aire WM series - IOM Attentions, Cautions, and Warnings CAUTION CAUTION CAUTION CAUTION DO NOT store or install units in corrosive environments or in DO NOT store or install units in corrosive environments or in For duct connected appliances containing A2L refrigerants, false For duct connected appliances containing A2L refrigerants, false locations subject to temperature or humidity extremes (e.g., attics,...
- Page 4 Adirondack Aire WM series - IOM General Information Inspection: Preparation of Units for Installation: Upon receiving your equipment, carefully check the 1. Verify Unit Shipment: Confirm that the electrical shipment against the bill of lading. Make sure you specifications on the unit’s nameplate match the have received all units.
- Page 5 Adirondack Aire WM series - IOM General Information intrinsically safe. • Refrigerant piping or components are installed in Presence of Fire Extinguisher: a position where they are unlikely to be exposed In the event that hot work is to be performed on...
- Page 6 Adirondack Aire WM series - IOM General Information Repair to intrinsically safe components: Table 1: Altitude Adjustment Intrinsically safe components must be replaced. ft (m) Cabling: 0 (0) 1.00 Ensure that the cabling is protected from wear, 656 (200) 1.00...
- Page 7 Adirondack Aire WM series - IOM Refrigerant System Servicing to avoid using compressed air or oxygen for purging The following leak detection methods are acceptable refrigerant systems. for all refrigerant systems: For appliances with flammable refrigerants, the Electronic leak detectors can be employed to purging process involves breaking the vacuum with locate refrigerant leaks;...
- Page 8 Adirondack Aire WM series - IOM Refrigerant System Servicing special cylinders for the recovery of refrigerant). • All personal protective equipment is accessible Cylinders shall be complete with pressure-relief and utilized properly. valve and associated shut-off valves in good working order.
- Page 9 Adirondack Aire WM series - IOM OPERATING LIMITS Minimum Cold Cooling Heating Model serviceable Start area (ft2) Min. Ambient Air WM-08 10.8 Min. EWT Min. EWT WM-10 14.4 Max. Ambient Air 95/78 WM-12 12.9 Max. EWT WM-15 18.4 Normal = 3.0 Max = 4.2...
- Page 10 Adirondack Aire WM series - IOM Installer - General Information and pull towards you to expose the chassis. Dispose We have designed and manufactured this unit to be of the room cabinet if the new unit comes with a new safe and trouble free.
- Page 11 Adirondack Aire WM series - IOM between 197V and 253V. Inadequate wiring and/or and outlet properly. If pipe thread fittings are used, improper electrical supply will likely result in failure use Teflon thread tape or pipe dope. When tightening of the compressor and other electrical components the water connections and drain at the unit use a and voids the warranty.
- Page 12 Adirondack Aire WM series - IOM • Has the water loop system been balanced to design WM Models - Cooling Operation: flow rates? 1). Open the cabinet control door. Locate the “COOL’, ‘OFF’, ‘HEAT’ and the ‘FAN’ ‘HI’ ‘LO’ push button •...
- Page 13 Adirondack Aire WM series - IOM Boilerless System: 6). A strainer (20 mesh or greater) may be used to Boilerless systems (systems in-which the building keep debris from entering the system and to help does NOT have a boiler as part of the closed loop ensure a clean system.
- Page 14 Adirondack Aire WM series - IOM 8). Be careful that the contaminated material does 9). Confirm that the drain line remains open following not come into contact with other areas of the unit the cleaning process. or building. Properly dispose of all contaminated materials and used cleaning solution.
- Page 15 Adirondack Aire WM series - IOM Before Calling for Factory Assistance A call to the factory is sometimes necessary for technical support or service/troubleshooting. We are happy to help! Before calling please gather and record the following information so that we are best able to help.
- Page 16 Adirondack Aire WM series - IOM TROUBLESHOOTING CHART The troubleshooting chart that follows is provided to serve as an aid for identifying malfunctions that may occur. Within the chart are three columns. 1. The Problems column describes what the unit is doing.
Need help?
Do you have a question about the Adirondack Aire WM Series and is the answer not in the manual?
Questions and answers