Summary of Contents for Tammiholma PREMIUM Atom.3 H
- Page 1 TAMMIHOLMA PREMIUM KÄYTTÖOHJEET / MANUAL EN Maahantuoja Tammiholma Oy Teerisuonkuja 5, 00700 Helsinki 09 350 5220 myynti@tammiholma.fi...
- Page 2 Important! This symbol attracts attention to important safety regulations which must be applied to avoid injury or damage to your property or that of others. Before starting work with your motor-sweeper, read all the instructions in this manual and the engine manual carefully, and follow them to the letter.
- Page 3 GENERALITIES (FIG.1) Data for motor-sweeper identifi cation Motor-sweeper type plate Petrol Electric CALLING IN THE AFTER-SALES SERVICE Before calling in the after-sales service, make a careful analysis of the problems and their causes When calling, please state: • Hours of operation. •...
- Page 4 TECHNICAL FEATURES (1/3) Versions Atom.3 H Atom.3 E (petrol) (electric) PERFORMANCES Max. cleaning capacity (with 2 side brushes) m²/h 7315 Cleaning width Main brush Cleaning width Main brush + Right side brush Cleaning width Main brush + 2 side brushes 1330 Max.
- Page 5 TECHNICAL FEATURES (2/3) Versions Atom.3 H Atom.3 E (petrol) (electric) ELECTRIC MOTORS Drive motor: Model type MRP9D Nominal power nr./V/W 1/24/400 Suction motor: Model type EVC004 2900 Nominal power nr./V/W 1/24/130 Main brush motor Model type S114SE 2800 Nominal power nr./V/W 1/24/400 RH Side brush motor...
- Page 6 TECHNICAL FEATURES (3/3) Versions Atom.3 H Atom.3 E (petrol) (electric) DRIVE Drive on wheel position front rear TRANSMISSION Transmission system type hydraulic electric WHEELS Front and Rear Ømm BRAKES Service and Parking brake type mechanical SUSPENSION Front and Rear type rigid WEIGHT Machine weight in working condition without operator...
- Page 7 CONTROLS AND COMPONENTS (FIG.3) (1A) Suction shut-off and fi lter shaking lever (petrol vers.) 1B) Suction shut-off and fi lter shaking button (electric vers.) V C C It serves to shut off suction on wet fl oors and to activate the fi lter shaker motor.
- Page 8 (8) Forward/reverse drive switch (electric sweeper) The switch 8 selects the direction of the sweeper FORWARD OR REVERSE. Position I = FORWARD Position II = BACK (reverse) Position 0 = Neutral Act on pedal 7 for the transfer. II II (9-11) Service brake pedal and parking brake handle The pedal and lock ball grip operate the service brake and parking bra- ke respectively.
- Page 9 GENERAL SAFETY REGULATIONS The machine described in this manual has been constructed in accordance with the Machinery Directive 2006/42/EC. The person in charge of the machine is responsible for complying with directives and local regulations on the working environment to ensure the health and safety of operatives.
- Page 10 STARTING WORK (FIG.5) Proceed as follows: 1B 8 • Check that the brushes are raised off the fl oor (levers 2, 6). • Release the brake pedal 9. • Insert the key 3 in the key switch and turn it clockwise. For the “petrol version”, see “starting the engine”.
- Page 11 REGULATIONS TO BE FOLLOWED DURING OPERATION • Never sweep up ropes, wire, straps, water, etc. • To pick up large but light objects (such as paper, leaves, etc.), raise the front fl ap of the machine by the pedal 10, fi g.3 slightly for just the time necessary to sweep the objects up.
- Page 12 MAINTENANCE (FIG. 7 - 8 - 9 - 10) (Petrol version) FIG.8 Engine Carefully follow the instructions in the HONDA GX 160 OPERATING AND MAINTENANCE manual for all engine maintenance operations. Always check the oil level in the engine before starting it up, using the dipstick 3, fi g.4.
- Page 13 MAINTENANCE (FIG.11 - 12) FIG.11 Main brush The main brush sweeps dust and refuse into the bin at the rear of the motor-sweeper. Caution! Never sweep up string, wire, etc., which can become entangled in the brush and damage the bristles. Adjusting the main brush The main brush is raised and lowered by lever 2, fi g.
- Page 14 MAINTENANCE (FIG.14) Removing and replacing the main brush The main brush can be removed from the left side of the motor-swee- per. Proceed as follows to remove and replace the main brush: • Open the brush inspection hatch 1. • Remove the brush protection (P).
- Page 15 MAINTENANCE (FIG.16) Checking and adjusting the tension of the pump drive belt Petrol (petrol sweeper) Every 40 hours work check the tension of the belt 1 which drives the pump. Proceed as follows to tension the belt if it is too slack. •...
- Page 16 STEERING SYSTEM (FIG.18) The motor-sweeper is steered by means of steering wheel 1. The steering wheel requires no adjustment. SERVICE AND PARKING BRAKES (FIG.19) The brake is used to stop the motor-sweeper when it is moving and to keep it stationary on slopes. The braking eff ect is provided by drums acting on the rear wheels.
- Page 17 DUST FLAPS (FIG.21) The dust fl aps prevent the dust raised by the brushes from blowing out from under the motor-sweeper. They must therefore be kept in peak condition and replaced if they become worn or damaged. Replacing the fl aps •...
- Page 18 ELECTRIC SYSTEM “PETROL VERSION” (FIG.24) The electrical system operates at 12 V and is powered by a battery 12 V - 40 Ah. Wiring diagram (petrol version) Wiring diagram description Electric cables colors F1 - Fuse 30A A - Light blue F2 - Fuse 10A B - White F3 - Fuse 25A...
- Page 19 ELECTRIC SYSTEM “ELECTRIC VERSION” (FIG.25A) The electrical system operates at 24 V and is powered by two 12 V, 118 Ah batteries (connected in series). Never continue operating the motor-sweeper until the batteries run fi g.25A/1 completely fl at. When indicator 12 (fi g.3) shows yellow, the batteries are starting to run down.
- Page 20 ELECTRIC SYSTEM “ELECTRIC VERSION” (FIG.25B/1)
- Page 21 ELECTRIC SYSTEM “ELECTRIC VERSION” (FIG.25B/2) Electric cables colors Safety microswitch (Fig.25B/1 - B/2) A safety microswitch integrated inside the seat enables electric circuits only with operator on A - Light blue board. B - White C - Orange G - Yellow H - Grey L - Blue M - Brown...
- Page 22 ALARMS DESCRIPTION (Diagnostics “LED 16 - Fig.3” electric version) Call the Authorized Service Staff Nr. Flashes Alarm description What to do Release the drive control to stop the LED fl ashing. If that does Drive control already active when turned on: the machine was not happen, it may be necessary to recalibrate the accelera- turned on with the drive control already activated.
- Page 23 ON BOARD BATTERY CHARGER “OPTIONAL” (FIG.26A) Caution! Read carefully the instructions handbook supplied with the bat- tery charger. The machine is designed for the installation of an on-board battery char- ger for systems powered by two 12V batteries or four 6V batteries. The battery charger is designed to charge lead-acid (standard) or gel bat- teries (optional).
- Page 24 DIPSWITCH CONFIGURATION TABLE FOR BATTERY CHARGER 24V 25A (FIG.26B) To access to the Dipswitches 3, it is necessary remove the charger 1 from the machine and its cap 2. DIPSWITCH In the following table you can fi ndmeaning of all diff erent position of dipswitch for programming the battery charger. Number of Status of the Reference...
- Page 25 ROUTINE CONTROL AND MAINTENANCE OPERATIONS AND SAFETY CHECKS The machine must be inspected by a specialist technician who checks its safety or for any damage or defects in the following cases: • Before it is put into operation • After modifi cations or repairs •...
- Page 26 TROUBLESHOOTING Problem Cause Corrective action The sweeper fails to pick up large particles of dirt or Working speed too fast Reduce working speed leaves traces of dirt behind. Brush pressur too light Adjust brush pressure (trace on fl oor) Brush worn Replace brush Bristles bent or string or wire etc., entangled in brush Remove string or wire...
Need help?
Do you have a question about the PREMIUM Atom.3 H and is the answer not in the manual?
Questions and answers