ProLinx 138IR-12C Instruction Manual

WIRELESS HIGH OUTPUT REMOTE CONTROL
COLOR CHANGING SPOT/CEILING LIGHT
MODEL NO: 138IR-12C
Instruction Manual
LOCATION OF CONTROLS:
1. Remote Control Signal Receiver and ON
White/Red/Green/Blue & OFF Switch
2. Diffused Lens
3. 30 Warm White SMD and 18 RGB LEDs
4. Battery Compartment Cover/Mounting Bracket*
5. Tab
6. Notch
7. 24 key Remote Control (see the function of each button at the bottom)
8. Remote Control Signal Transmitter
9. Remote Battery Compartment*
10. 2 Mounting Screws
11. 2 Plastic Anchors
*On back of unit/remote
INSTALLATION
Detachable Bracket and Screws (included)
Prepare 3 x 1.5V D Battery (not included).
1. Remove the Battery Compartment Cover/Mounting Bracket from the back
of the light by pushing to the direction with OPEN arrow.
2. Using the detachable mounting bracket as a guide to mark & drill two (2)
pilot holes in the location where you want to mount the light.
3. Place 2 screws (included) into the mounting bracket and pre-drilled holes.
Tighten screws into the mounting bracket until it is secure to surface.
Do not over tighten.
4. Fasten the light to the mounting bracket by aligning the notch of the light to the
tab of the mounting bracket and turning light clockwise (see Figure 1).
To Install Batteries Before Light is Mounted:
1. Remove the battery compartment cover/mounting bracket from the bottom of the light.
To do so, keep the "Open" markings on the mounting bracket are at the top of the light,
twist the mounting bracket counter clockwise (in the direction of the "OPEN" arrow) and
then release it from the light head by facing it down.
NOTE: It may help to turn the light head or mounting bracket clockwise or
counter-clockwise as you are pulling it off.
2. Install all (3) three new D Alkaline batteries, observing the indicated
polarities (+)/(-) (Not included).
3. Replace battery compartment cover by placing it back on the light making sure that the "Open"
markings are at the top of the light. Aligning the tab of the battery compartment cover to the
notch of the light, twist the battery compartment cover clockwise until it locks into
position (in the opposite direction of the "OPEN" arrow).
To Replace Batteries Once Light is Mounted:
If the LEDs appear to be dim, this is an indication that batteries need to be replaced.
1. The light body will release from battery compartment cover/mounting bracket easily.
To do so, place fingers around light body, twist it counter clockwise & pull down gently
to release light head and expose battery compartment.
2. Remove old batteries (if replacing batteries).
3. Replace with (3) three new D Alkaline batteries, observing the indicated
polarities (+)/(-) (Not included).
4. Fasten the light to the mounting bracket by aligning the notch of the light to the tab
of the mounting bracket and turning light clockwise (see Figure 1).
Replacing the Remote Control Battery (1 CR2025/CR2032 button battery required)
This product contains a Button Cell battery. If swallowed, it could cause severe injury or
death in just 2 hours. Seek medical attention immediately.
If the Remote Control does not work to turn the LED lights ON, this may be an indication that the battery
needs to be replaced. Please insert 1xCR2025 or 1xCR2032 button cell battery & follow the correct polarity as indicated.
OPERATING INSTRUCTIONS (LIGHT)
˙1st press Remote Control Signal Receiver to turn warm white light ON.
˙2nd press to turn red light ON.
˙3rd press to turn green light ON.
˙4th press to turn blue light ON.
˙Press again to turn the light OFF.
Remote Control Operation:
ON, OFF, DIMMER, COLOR, TIMER, FLASH, STROBE, FADE, SMOOTH (Operating distance is up to 20 feet in an open area
without obstacles. For best operation, we recommend to direct the Remote Control towards the Remote Control Signal Receiver
on lights. Physical objects between the remote and the lights may interfere with the Infra Red signal. Up to 10 lights can be
controlled by one remote control).
*Lights will default to last brightness & color setting when you turn lights off & on again via remote. If you
want to adjust the brightness level of lights again, please press (+)/(-) buttons on remote.
NOTE:
Press 1HR, 2HR, 3HR, 4HR button to set timer. Light will flash once to activate timer. Press ON to
cancel timer setting. Light will also flash once.
Operations:
Increase brightness & speed
up Flash/Strobe/Fade/Smooth
(Level 1 to 5)
Specifications of 138IR-12C
Lumens: 250 LM Max.
Slide battery drawer out
Insert 1×CR2025/CR2032
Run Time: 70 hours
button cell battery
LED: 30 pcs 4000K Warm White SMD & 18 RGB
MADE IN CHINA
REMOVE PLASTIC TAB FROM REMOTE PRIOR TO USE
Direct the Remote Control towards Remote
Decrease brightness & slow
Control Signal Receiver on lights up to 20 feet
down Flash/Strobe/Fade/
Smooth (Level 1 to 5)
12 default colors
7 color flashing in cycle: Approx. 10 seconds (level 1),
15 seconds (level 2), 20 seconds (level 3), 25 seconds
(level 4), 30 seconds (level 5)
7 color changing in cycle from bright to dim: Approx.
8 seconds (level 1), 12 seconds (level 2), 16 seconds
(level 3), 20 seconds (level 4), 24 seconds (level 5)
7 color change gradually: Approx. 10 seconds
(level 1), 15 seconds (level 2), 20 seconds (level 3),
25 seconds (level 4), 30 seconds (level 5)
White
7 color flashing in cycle plus RGB color change
gradually: Approx. 20-60 seconds (level 1-5)
Timer Setting: 1/2/3/4 Hours
Wattage: 2.5 W
LED Lifespan: 30000 Hours
Voltage of Light: DC4.5V (3*D Battery)