Subscribe to Our Youtube Channel
Summary of Contents for Frigicoll MA3-PCK
- Page 1 INSTALLATION & OWNER'S MANUAL Protocol Conversion Kit MA3-PCK (KA3-PCK) Original Manual Thank you for purchasing our product. Before using the unit, please read this manual carefully and keep it for future reference.
- Page 3 Contents Safety Precautions ..................1 Product Description .................3 1 Debugging and Solutions ..............5 Web Configuration ...................7 1 System Settings ................7 2 Firmware Upgrade ................8 Installation Instructions ................9 1 Product Overview .................9 2 Product Dimensions .................9 3 Installation Accessories ..............10 4 Installation Method .................10...
- Page 4 Safety Precautions Precautions The Operation and Installation Manual of this product describes how to properly handle the product, how to prevent harm to others and prevent property losses, as well as how to use the product correctly and safely. Read the following carefully, make sure you understand the content (symbols and marks), and observe the precautions below.
- Page 5 Warning • This unit must be installed by professional technicians. Users are not allowed to install the unit themselves; otherwise, personal injury or damage to the controller may occur. • Other electrical wiring work must be carried out by a professional technician according to the circuit diagram.
- Page 6 Product Description The protocol conversion gateway (here in after referred to as "gateway") converts the V6/S6 series VRF protocol into the V8/S8 series VRF protocol, enabling the V6/S6 series VRF system to connect to the V8/S8 centralized control gateway. PROTOCOL CONVERSION KIT X Y E A1 B1 E A2 B2 E Port...
- Page 7 Indicator Type Status Function Gateway powered off Power supply Steady on Gateway powered on Off/steady on Abnormal communication X1Y1E X Y E communication status Blink Normal data Off/steady on Abnormal communication A1B1E A1 B1 E communication status Blink Normal data Off/steady on Abnormal communication A2B2E...
- Page 8 1 Debugging and Solutions 1.1 Debugging Connect the X, Y and E ports on the ODU to those on the gateway. Power on the gateway. (*1) (*1) When the refrigerant system is powered on, system detection will take some time. During this period, the gateway may obtain incorrect information about the refrigerant system.
- Page 9 1.2 Solutions If the gateway does not detect the refrigerant system (with the displayed number of IDUs and that of ODUs being 0), follow these steps to check the communication between the gateway and the refrigerant system: 1. Check whether the refrigerant system is just powered on. After the refrigerant system stabilizes (approximately 15 minutes after the power-on, depending on the refrigerant conditions), check whether the gateway can detect the IDUs and ODUs.
- Page 10 Web Configuration 1 System Settings The IP address of the gateway is 192.168.1.200. The IP address for accessing the PC on the Web page of the gateway must be on the same subnet segment as the gateway. Upon gateway setting, enter "192.168.1.200" in the address bar in Google Chrome (recommended).
- Page 11 2 Firmware Upgrade To update the gateway firmware, click "Upload" and select the upgrade package. Once the progress bar reaches 100%, the upgrade package has been successfully uploaded. Following the restart of the gateway, the firmware will be automatically updated. Caution •...
- Page 12 Installation Instructions 1 Product Overview PROTOCOL CONVERSION KIT X Y E A1 B1 E A2 B2 E 2 Product Dimensions Unit: mm 51.5 74.5...
- Page 13 3 Installation Accessories Please check that you have all the following parts. Name Quantity Remarks Self-tapping screw ST4*20 Plastic expansion pipe For installing the controller onto the wall 3-pin black terminal For communication 3-pin gray terminal For connecting the power supply 4 Installation Method I.
- Page 14 Phillips head screw ST4*20 (This screw is Plastic pre-inserted into the wall expansion pipe and the distance from the highest position of the nut to the wall is 5.5mm) Drill with a 6mm drill bit, with a Phillips drill depth of head screw no less than ST4*20...
Need help?
Do you have a question about the MA3-PCK and is the answer not in the manual?
Questions and answers