Advertisement
Quick Links
2024-08-01
NOTE! Before assembly it is recommended to
inspect all parts and if needed, sort them so
eventual "ugly" knots or similar are placed so
they are less visible.
Special attention must be paid to the following:
1. All wooden parts must be stored at a dry
location and be dry during assembly. Never
assemble in the rain or when humidity is
high. Wood is a living material and swells
when humidity is high.
Also see page with checkpoints!
NOTE! Before assembly it is recommended to inspect all parts and if needed, sort them so eventual knots or similar are used
so they are not readily visible. Assemble the sauna on a flat surface. Note part no.1 is not part of the package.
Place the stave with the cutouts up in the middle of the base
and screw it in place (holes are pre-drilled 35 mm) on both
sides. This shall be done on both sides.
Start placing out the staves, alternate between the shorter
(57cm) and longer staves (196 cm). This is what it shall look
like after a while. See last page for assembly principle!
1
Assembly instructions for Barrel Sauna
1
Assemble the base of the sauna, the parts fit into pre-milled
grooves. Screw the parts together (holes are marked, 55
mm) NOTE! See page 18 for SLD200035 base assembly
Screw the bottom stave in place on both sides (35 mm) NOTE!
This stave is 1cm shorter at each end for water drainage.
Adjust the staves so the groove is straight. Feel with your
fingertips to make sure the staves align properly.
1
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for SpaDealers SLD200025
- Page 1 Assembly instructions for Barrel Sauna 2024-08-01 NOTE! Before assembly it is recommended to inspect all parts and if needed, sort them so eventual “ugly” knots or similar are placed so they are less visible. Special attention must be paid to the following: 1.
- Page 2 Then screw the outer staves in place in both sides, both front At this stage place the first Gable module (B1) on the back. and rear. Screw into the 5 stave from the center stave. Tongue side up! See picture on page 15. The markings on the gable module are to be lined up against Tap gently on the gable module with a rubber mallet.
- Page 3 70mm Then attach the next rear module. NOTE! Put in the included Then attach the right part of the front gable (check that the plugs (12x75) before attaching the next module. right side faces outwards). Screw the modules to each other where the pictures indicate (70mm), also see lower right picture.
- Page 4 NOTE! Use the accompanying wedges to keep the staves in place so they do not fall out during assembly. The wedges can be removed after assembly is complete. Assemble the wedges on all sides when you have reached this stage Start attaching the staves from the bottom, going in a counter clockwise direction.
- Page 5 CHECKPOINTS NOTE! When 18 staves have been assembled from checkpoint 1 to the right, you have reached checkpoint 2 and from 1 to the left checkpoint 4! If the stave size is normal* and you have followed the assembly line and all staves are mounted tightly together (image B, page 2), then the flat outermost points should be between the control points shown in the image marked "Correct".
- Page 6 How to correct This example is based on all staves Incorrect being mounted close together and following instructions on page 2 with images A and B. Example, you have reached checkpoints 2 and 4, you have exceeded by 6 mm on each side, a total of 12 mm.
- Page 7 Keep on assembly in a counter clockwise direction Verify at checkpoint 3 that the inner flat surface of the rod lines up with the markings. See pages 5 - 6 for more info. When you get this far, stop adding staves counter clockwise The last two staves are not tapped in completely, but must and begin adding from the other side.
- Page 8 Walk around and tap the stave where they meet the gable Adjust the staves using a rubber mallet as the straps get modules as you tighten the stainless-steel straps. progressively tighter. 124cm 124cm Insert the short staves that do not have a cutout between the Attach the last strap according to the measurements shown in rods as shown in the picture.
- Page 9 Place the first strip of roofing material. Place the roofing material as shown by the pictures. Build from below from each side until you reach the top of the sauna. The arrows show nails (included in package). Do not assemble the roof completely where the chimney will go.
- Page 10 32cm center Mark out a circle with the jig that comes with the sauna, hole Drill a starting hole. Cut out the circle using a saw. diameter 38cm. The center of the circle should be 32cm measured from the rear edge of the sauna. Now place the roof shingles over the hole without nailing them into place.
- Page 11 Put the rubber gasket in place. Note that the rubber gasket Cut out the circle with a carpet knife (box cutter) is placed on top of the shingles. Otherwise rain water will run down under the shingles. Assemble the remaining shingles and nail them in place. Use a heat gun to activate the glue.
- Page 12 Now put the top strip in place. Cut the far edge of the strip so Attach the top strip using heat only. it matches the hole for the chimney. If you have an electric sauna, cover the roof from edge to edge using the strip. Cut away the excess top strip.
- Page 13 Use the heat gun to glue the adhesive to the sauna and press the lowest shingles firmly against the sauna. It is not necessary to heat all shingles. The glue will be activated by the sun later. Installation of edge follows. It is important that the first parts of Do use a water level to make sure it is straight.
- Page 14 Now assemble the parts above, but don’t use screws yet. Adjust the parts until they are located evenly and everything looks good. Then screw them in place. Same method is used to attach the rear edge. Attach the plastic plugs in the screw holes. Affix plastic plugs in place with rubber mallet.
- Page 15 Screw the frame in place (screw holes are marked) Put the seats back in. 55mm 35mm Install support, one per side. NOTE! The length of these may need to be adjusted, depending on how exactly the bench frame is mounted. Installation of door frame.
- Page 16 Install the frame in the door and screw it in place, screw holes Assemble the outside benches in the same way as the interior are pre-marked, 55 mm. benches. Assemble support leg, the support leg is screwed into the wall and in the bench (55 mm, wooden plug 8x35). Picture below shows all benches assembled.
- Page 17 Finally, the door is assembled. Fasten the hinges in the pre- Screw door and handles in place. Now try and close and open marked places, 25 mm + hinges. the door. Check that the latch is working properly. If the door wont latch, see the steps below: Sometimes the door frame might bend inwards behind the strike plate and the roller latch cannot engage in the strike plate.
- Page 18 Door catch is installed on the door frame...
- Page 19 Base assembly for SLD200035 Base 2 x 400 mm 4 x 1350 mm Front 900 mm...
- Page 20 Skruvar 4,2 x 35 mm Front...
- Page 21 989 2 0174 4044 000...
- Page 22 The stove pipe is pushed upwards and through the rubber cuff. The stovepipe is then adjusted so that it lies well against the stove. The upper rubber cuff must then be pulled upwards on the stovepipe so that a slope is formed for the rain. See page 13.
- Page 23 Assembly principle SLD200025 NOT SHOWN IN PICTURE SEE PAGE 8 1960 1800 1960 619.70 1310...
Need help?
Do you have a question about the SLD200025 and is the answer not in the manual?
Questions and answers