HyperChiller HC2 Series, EBC-1023 Series (HC1, HC2W) Manual

PARTS IDENTIFICATION

1. Lid
2. Small stainless steel cup
3. Large stainless steel cup
4. Black HyperChiller cup

NOTE: The small stainless steel cup nests inside the large stainless steel cup. Both cups can be attached and detached from the lid by twisting.

INITIAL ASSEMBLY INSTRUCTIONS

1. Fill small stainless steel cup with water up to the Indented Mark or MAX fill line and twist securely on to the lid. (Avoid overfilling to prevent cracking).
   
2. Fill large stainless steel cup with water up to the Indented Mark or MAX fill line and empty contents into the black HyperChiller cup. (Avoid overfilling to prevent cracking).
   
3. Twist empty large stainless steel cup securely on to the lid.
   
4. Twist lid assembly securely on to the black HyperChiller cup.
   
5. Place the HyperChiller upright in freezer until frozen solid, minimum 12 hours. NEVER place the HyperChiller on its side or at an angle when freezing to prevent leaking or cracking due to uneven freezing.
   

INSTRUCTIONS FOR DAILY USE

STEP 1:
Brew fresh coffee directly onto the recessed area of the Hyperchiller's lid with your compatible single cup brewer, or carefully pour it in with a carafe. Liquid will flow through the opening at the bottom of the lid, and into the cooling chamber.

NOTE: It is OK to pour liquid over the vent on the recessed area of the lid. During use it enables air to escape from the ice chamber, so you may see small bubbles coming from it. Also, once frozen, there is no need to take the product apart for regular use.

STEP 2:
After the coffee is inside of the Hyperchiller, gently swirl the product every few seconds to keep the coffee moving.

Use caution when handling hot liquids.

STEP 3:
In as little as one minute, the coffee will have cooled down by up to 130°F/54°C+. Pour via the spout on the opposite side of the lid into your cup and enjoy!

NOTE: Cooling time requirements vary based on freezer temperature, initial liquid temperature & volume, as well as whether the product is swirled or not. Please refer to "Cooling Times" chart below.

STEP 4:
To prepare for your next use, simply pour clean water through the lid (as you did with the coffee), and then pour back out into the sink. Lastly, dry off condensation from the outside, and put the product back in the freezer in an upright position.

Note: NEVER place the HyperChiller on its side or at an angle when freezing to prevent leaking or cracking due to uneven freezing.

HYPERCHILLER COOLING TIMES

*To enjoy your coffee ice cold, without ice in your drink, add 60+ seconds to the corresponding cooling time.

GENERAL INFORMATION

Periodically, the product should be taken apart and thoroughly washed. All parts are top shelf dishwasher safe.
For a demo video of product assembly & use go to: https://hyperchiller.com/pages/how-it-works-video

IMPORTANT SAFEGUARDS

The Hyperchiller Brand takes consumer safety very seriously. Products are designed and manufactured with our valued consumers' safety in mind. Additionally, we ask that you exercise a level of caution when using any non- electrical or electrical appliance by following all instructions and important safeguards.

Ensure that this device is stable and secure as you slowly and carefully pour hot liquid into the device. Do not allow any liquid to overflow from or pool on the top of the vessel. Be sure that the liquid drains from the top completely before you continue pouring liquid into the chamber. Do not overfill.

WASH BEFORE USE (Top shelf dishwasher safe)

Visit: shopelitegourmet.com for Live Chat Support and Contact Us Form for assistance with your product.

Documents / Resources

References

• https://hyperchiller.com/pages/how-it-works-video
• Shop Elite Gourmet - Small Kitchen Appliances

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download HyperChiller HC2 Series, EBC-1023 Series (HC1, HC2W) Manual