1. Manuals
  2. Brands
  3. ENDEVCO Manuals
  4. Motherboard
  5. 4876
  6. Instruction manual

ENDEVCO 4876 Instruction Manual

2680b sensitivity programmer
Hide thumbs
1
2
3
4
5
6
7

Advertisement

Table of Contents

REV NR, ECO 54817
8/21/24
Piezoelectric accelerometers
ENDEVCO
2680B Sensitivity Programmer
|
Piezoresistive accelerometers
|
IEPE accelerometers
intensity microphones
|
Inertial sensors
www.endevco.com
|
Variable capacitance accelerometers
|
Signal conditioners and supportive instrumentation
Tel: +1 (866) ENDEVCO [+1 (866) 363-3826]
Model 4876
Instruction Manual # 77080
|
Piezoresistive pressure sensors
|
Piezoelectric pressure sensors
|
Cable assemblies
IM 2680B 77079 013124
®
|
High
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 4876 and is the answer not in the manual?

Questions and answers

Summary of Contents for ENDEVCO 4876

  • Page 1 Piezoelectric accelerometers Piezoresistive accelerometers IEPE accelerometers Variable capacitance accelerometers Piezoresistive pressure sensors Piezoelectric pressure sensors High intensity microphones Inertial sensors Signal conditioners and supportive instrumentation Cable assemblies ENDEVCO www.endevco.com Tel: +1 (866) ENDEVCO [+1 (866) 363-3826] IM 2680B 77079 013124...
  • Page 2 01 CONNECTION AND POWER ON ......................3 02 DIAGNOSTIC SCREENS .......................... 4 03 MAIN SCREEN AND FUNCTION DESCRIPTIONS ................6 04 BURN SENSITIVITY TO MODULE ......................7 Tel: +1 (866) ENDEVCO [+1 (866) 363-3826] ENDEVCO www.endevco.com IM 2680B 77079 013124...

  • Page 3: 01 Connection And Power On

    1) Connect the 7-pin circular connector of the 2680B module to the “2680 I/O” DB-9 connector using the 100-18846-40 output cable (provided in 4876-KIT). 2) Connect power to the Model 4876 Sensitivity Programmer, using the 100-18846-30 (18VDC) external power supply (provided in 4876-KIT). The device will illuminate the POWER and DEVICE POWER LEDs.

  • Page 4: 02 Diagnostic Screens

    A power out of range error will be displayed if the external power supply is not within 18VDC ± 2V. Power Out of Range A “Power Issue Corrected” screen will display once the correct voltage is applied. Power Issue Corrected Tel: +1 (866) ENDEVCO [+1 (866) 363-3826] ENDEVCO www.endevco.com IM 2680B 77079 013124...
  • Page 5 1) There is physically no module connected. 2) There is a module connected but either the data lines are bad or the programmer is unable to communicate with the module. Module Not Connected Tel: +1 (866) ENDEVCO [+1 (866) 363-3826] ENDEVCO www.endevco.com IM 2680B 77079 013124...

  • Page 6: 03 Main Screen And Function Descriptions

    See “Burn Sensitivity to Module” section. Note: The cursor will be seen blinking with a line under its location ENDEVCO www.endevco.com Tel: +1 (866) ENDEVCO [+1 (866) 363-3826] IM 2680B 77079 013124...

  • Page 7: 04 Burn Sensitivity To Module

    If at any point you press [N], you will receive a Value not saved screen that will list the remaining burns left in the digi-pot. Tel: +1 (866) ENDEVCO [+1 (866) 363-3826] ENDEVCO www.endevco.com...

Table of Contents