Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for RoboSea WARP 10
-
Page 2: Table Of Contents
CONTENT INTRODUCTION WARNING PARTS DIAGRAM BATTERY INSTRUCTION GETTING STARTED CARE & MAINTENANCE CAMERA ASSEMBLY... -
Page 3: Introduction
INTRODUCTION The new generation of foldable sea scooter Warp 10 has a speed of up to 7. 2km/h (4.5 mph), and can freely switch the speed between 3 gears, which can bring you the enjoyment of underwater cruising. Seascooter is designed for use in seawater. It is less buoyant in fresh water, lakes or swimming pools and may sink into such waters. - Page 4 Be careful when using Seascooter near people with long hair. Long-haired users should wear a headband or a swimming cap when using Seascooter. Pay attention to proper water level, tidal changes, dangerous currents, weather changes and strong sea breeze. Before venturing out, be sure to search for unfamiliar water.
-
Page 5: Parts Diagram
• In different waters (seawater, lakes, swimming pools), conditions such as water flow, temperature, and pressure can affect the buoyancy of the device and may cause it to sink if accidentally sunk. • When using Seascooter for scuba diving, the ascent and descent should follow accepted diving conventions. -
Page 6: Battery Instruction
1.Front Grille 7.Foldable Control Handles Release Buttons 2.Camera Mount(Camera not included) 8.Rubber Handle 3.Speed Control 9.Battery 4.Start Buttons 10.Battery Charging Base 5.Control Handles(Foldable) 11.Charger 6.Battery Indicator BATTERY INSTRUCTION Battery installation Battery charging BATTERY CAUTION Always remove the battery from the Seascooter for storage. Do not discharge the lithium-ion battery for a long time - the battery will discharge itself and the charge may drop enough to damage the battery. -
Page 7: Getting Started
Use the specified charger ONLY. It must be dealt with properly. The battery MUST be charged after each use. Whennotinuse,thebatteryMUSTbechargedatleastonceeverythree months. Do not put the battery in fire, direct sunlight or heat the battery; Otherwise, it may explode or leak. Keep lithium-ion batteries away from high temperatures - high temperatures may cause premature battery failure. - Page 8 Step 3 Press the speed control button to the Medium High gear position to adjust the speed. Step 4 Pay attention to the power indicator, when the power is lower than 40% or 20%, the indicator turns red. Step 5 Press the button underneath the control handle.
-
Page 9: Care&Maintenance
WARNING Make sure use the Seascooter in the correct position. When using the Seascooter, maintain the correct posture to achieve maximum speed. Do not put your hands or any other objects into the propeller. CARE&MAINTENANCE Washing and Care The Seascooter must be cleaned after each use. Before long time storage, please dry the Seascooter in a well ventilated and cool place. -
Page 10: Camera Assembly
If there is sand in the battery housing, please gently wipe the sand from the machine, taking care not to scratch the sealing surface. CAMERA ASSEMBLY ATTACHING YOUR CAMERA TO SEASCOOTER MOUNTS (Can be used with GoPro HERO [3, 3+, 4, 5, 6 or 7] cameras, or other camera with using the same mount system) To attach your camera to Seascooter, you will need a thumb screw or hardware depending on the mount you are using. - Page 11 Please read your User Manual and find solutions for your questions. -STEP2- Contact your local distributor in your region for after-sales technical support. * The customer pays the cost of delivery to the dealer. -STEP3- Contact Robosea After-sales Service Team at- service@roboocea.com.
- Page 12 Boya Gongdao (Beijing) Robot Technology Co.,Ltd. Email: hello@roboocean.com www.robosea.org...
Need help?
Do you have a question about the WARP 10 and is the answer not in the manual?
Questions and answers