Subscribe to Our Youtube Channel
Related Manuals for FoxESS L11P
Summary of Contents for FoxESS L11P
- Page 1 USER MANUAL 11kW AC EV Charger Address: FOXESS CO., LTD. No. 939, Jinhai 3rd Road, Longwan District, Wenzhou, China Tel: +86(510) 68092998(General) +86(510) 68101679 (Sales) V1.0 Website: www.fox-ess.com...
-
Page 2: Table Of Contents
Table of Contents Notes on this Manual 1.1 Scope of Validity 1.2 Target Group 1.3 Symbols Used Safety Packing List Introduction Technical Data Installation 6.1 Product Handling 6.2 Out of the box inspection 6.3 Install APP download Operation Maintenance Decommissioning 10.1 Dismantling the charger 10.2 Packaging 10.3 Storage and Transportation... -
Page 3: Notes On This Manual
Symbol Explanation CE mark. The charger complies with the requirements of the applicable CE guidelines. Beware of hot surface. L11P The charger can become hot during operation. Avoid contact Note during operation. -
Page 4: Safety
Safety Packing List EV chargers are designed and tested in accordance with international safety requirements. However, certain safety precautions must be taken when installing and operating this. The installer must read and follow all instructions, cautions and warnings in this installation manual. - All operations including transport, installation, start-up and maintenance, must be carried out by qualified, trained personnel. -
Page 5: Introduction
Introduction Technical Data FOX-ESS 11kW AC-CHARGER SPEC ⑧ ③ Model L11P Input Input line 3L/N/PE ⑦ ④ ① Rated voltage 400Vac，±20% Rated current Rated frequency 50/60Hz ⑥ ⑤ ② Output Output voltage 400Vac，±20% Maximum output current Rated power 11kW Interaction method ①Meaning of lights... -
Page 6: Installation
Installation Installation Ensure that the wall or column is vertical or positive 15 ° before installation. Product Handling To ensure safety, the following points should be paid attention to: -All accessories are placed separately during transport or handling. -Avoid violent shock and impact, and take it lightly. -Avoid inversion. - Page 7 Installation Installation Step 3: Floor type / Vertical installation method Secure the mounting backplate (B) and Type 2 Plug holder (J) to the wall with screws (D)and(L). Step 1: 1. Use a 12mm drill bit to drill four 60mm deep holes with a spacing of 170*120mm.
- Page 8 Installation Installation Step 4: Electrical Connections（Bottom entry） Fix the Mounting backplate (B) and Type 2 Plugholder(J)to the column with screws. A leakage protection switch needs to be installed. The leakage protection switch should use Type A, Type C20 leakage protection device is recommended, and the input wire should be led out from the leakage protection switch.
- Page 9 Installation Installation Step 3: Communication wiring(Bottom entry, when external meters need to be Unscrew the wiring cover screws and open the wiring cover. connected) Step 5: Trim all cables (wire diameter 0.3mm²) to 15mm (as shown in the figure), peel o the insulation sheath to expose the conductor by about 8mm. Unscrew the screws 0.5 N·m...
- Page 10 Installation Installation Electrical Connections（Back entry） Step 8: Install the cable wires into the terminals and lock the screws, press the tubular Complete steps 1, 2, and 3 in electrical connections (bottom entry)steps first, pre-insulated terminal E0508. then follow the steps as the following steps. Step 1: 0.5 N·m , process a hole of Φ40mm.
- Page 11 Installation Installation Communication wiring(Back entry, when external meters need to be Step 5: connected) Install the cable wires into the terminals and lock the screws, press the tubular pre-insulated terminal E0508. Complete steps 5 and 6 according to communication cable (bottom entry), and then perform the following steps.
-
Page 12: App Download
Operation APP download Charging mode and Operation Users can scan the QR code (Android and IOS ) in the quick installation guide . Users can set three charging modes through the charging mode setting interface of the APP: plug and charge, controlled, locked . A. -
Page 13: Maintenance
Operation Maintenance Troubleshoot by alarm information on APP or LCD display. Controlled mode with APP If fault occurs, users can check the fault information on the APP or by blinks of Start Charging: the LED indicator light. 1. Set the charger to the controlled mode. 2. -
Page 14: Decommissioning
Decommissioning 10.1 Dismantling the charger -Disconnect the charger from AC input and AC output. -Disconnect communication and optional connection wirings. Remove the charger from the bracket. -Remove the bracket if necessary. 10.2 Packaging If possible, please pack the charger with the original packaging. If it is no longer available, you can also use an equivalent box that meets the following requirements.
Need help?
Do you have a question about the L11P and is the answer not in the manual?
Questions and answers