Advertisement
Table of Contents
Advertisement
Table of Contents
Related Manuals for Nexgrill 710-0691A
Summary of Contents for Nexgrill 710-0691A
- Page 1 This Owner's Manual is provided and hosted by Appliance Factory Parts. Nexgrill 710-0691A Owner's Manual Shop genuine replacement parts for Nexgrill 710-0691A Find Your Nexgrill Grill Parts - Select From 922 Models -------- Manual continues below --------...
-
Page 2: Dear Customers
5270 Edison Avenue., Chino, CA 91710 (Tel) 800-790-1299 (Fax) 909-718-1949 NOTICE Dear Customers: Thank you for choosing our barbeque grill and hope that you enjoy our product. Our gas valves and components are preset at the factory to operate on Liquid Propane (LP). If you wish to convert your grill from LP to Natural Gas (NG), we strongly recommend that you hire a professionally trained technician to convert the unit. - Page 3 Natural Gas Conversion for Model# 720-0691A 720-0691A NG Conversion Kit for Model # WARNING! FALURE TO HEED THESE WARNINGS COULD RESULT IN A FIRE OR EXPLOSION THAT COULD CAUSE SERIOUS BODILY INJURY, DEATH OR PROPERTY DAMAGE. Installation of this Natural Gas Conversion kit must be performed by a QUALIFIED GAS TECHNICIAN ONLY. DO NOT ATTEMPT TO INSTALL THIS KIT YOURSELF.
- Page 4 Natural Gas Conversion for Model# 720-0691A Warning: Make sure all grill components are completely cool and gas supply is turned off and removed from grill prior to performing the conversion. NG Hose and Regulator Conversion Tools required: Phillips Head Screwdriver (+) 14mm wrench Turn all knobs to OFF.
- Page 5 Natural Gas Conversion for Model# 720-0691A Note: Make sure the orifice will be lined with valve when loose out and replace orifice in Main Tube Burner Conversion, Searing Side Burner conversion and Rear burner Conversion. And then test gas leak accordingly. Main Tube Burner Conversion Tools required: Phillips Head Screwdriver (+)
- Page 6 Natural Gas Conversion for Model# 720-0691A Searing Side Burner Conversion Tools required: Phillips Head Screwdriver (+) 6 mm Nut Driver The step-by-step instruction for converting the searing side burner’s orifice are stated below. Remove the screw under C bracket to take off the C bracket, then remove the searing side burner from the firebox by loosening the screws securing the burners near the back wall of the firebox.
- Page 7 Natural Gas Conversion for Model# 720-0691A Rear Burner Conversion Tools required: Phillips Head Screwdriver (+) 6mm Wrench Steps ： Remove the screws securing the rear baffle from inside the firebox. Remove the Rear Baffle from the back of the grill. Remove the LP orifice with 6mm wrench.
- Page 8 Natural Gas Conversion for Model# 720-0691A For Main Tube Burner Conversion Only (The 3 steps below are not necessary for the Sear side burner and Rear burner ) You will need to adjust the High Flame setting screw when converting the barbecue from Propane to Natural Gas. Please follow the steps as detailed below.
-
Page 9: Flame Characteristics
Natural Gas Conversion for Model# 720-0691A WARNING: IMPORTANT! TO LIGHT THE SEARING SIDE BURNER BEFORE LIGHTING… To light the searing side burner, remove any cooking Inspect the gas supply hose prior to turning the gas utensils from the burner grate. Push and turn the control “ON”. - Page 10 Natural Gas Conversion for Model# 720-0691A Note: Remove all packaging, including straps, before using the grill Make sure the lid is open. Push and turn Main Burner knob slowly to IGNITE/HI. Keep knob pressed in until the burner is lit. If burner does not light within 5 seconds, turn the knob to OFF and repeat the lighting instruction.
-
Page 11: Exploded View
Natural Gas Conversion for Model# 720-0691A Match light If the burner will not light after several attempts them the burner can be match lit, before using the match allow 5 minutes for any accumulated gas to dissipate. Clip a paper match on one end of the lighting rod. Light match.
Need help?
Do you have a question about the 710-0691A and is the answer not in the manual?
Questions and answers