Summary of Contents for Avitech IV-6054
- Page 1 Four-channel programmable DC power supply instruction manual PSIV3600系列可编程直五路 AVITECH INSTRUMENT INC.
- Page 2 Preface respected user: Hello! Thank you for purchasing a new Avetech instrument. In order to use this instrument correctly, please read this manual carefully before using this instrument, especially the section on "Safety Precautions". If you have read the full text of this manual, it is recommended that you keep this manual in a safe place and place it with the instrument or in a place where you can read it at any time for future reference.
-
Page 3: Copyright Information
Copyright Information ● Dongguan Avetech Instrument inc. all rights reserved. ● Products are protected by patents in China or other countries, including patents that have been obtained or are pending. ● Dongguan Avetech Instrument inc. reserves the right to change product specifications and prices. - Page 4 Verification and Correction Statement The company specifically declares that the instruments and equipment listed in this manual fully conform to the specifications and characteristics stated in the company's technical specifications. This instrument has passed the factory calibration of the company before leaving the factory, and the calibration procedures and steps are in line with the specifications and standards of the electronic inspection center.
-
Page 5: Table Of Contents
MATRIX TECHNOLOGY INC. www.szmatrix.com;sales@szmatrix.com CONTENTS CHAPTER I PRODUCT INTRODUCTION......................1 CHAPTER II TECHNICAL SPECIFICATIONS....................1 2.1 Main technical specifications....................,........1 2.2 Supplementary features............................,..2 CHAPTER III QUICK STAR..........................3 3.1 Introduction to the front and rear panels........................3 3.2 Pre-check...................................5 3.3 If the power does not start............................5 CHAPTER Ⅳ... -
Page 6: Chapter Iproduct Introduction
MATRIX TECHNOLOGY INC. www.szmatrix.com;sales@szmatrix.com Chapter Ⅰ Product Introduction Four-channel programmable DC power supply is a new generation of high-quality programmable linear DC power supply. All four channels can independently adjust voltage and current. This series of products is equipped with RS232 communication interface, which has the characteristics of desktop and system type, and can be arbitrarily matched with other instruments , integrated into a test system with special functions to meet the measurement requirements in different occasions, and the host computer program can be edited through the communication protocol, which brings great... -
Page 7: Chapter Ii Technical Specifications
MATRIX TECHNOLOGY INC. www.szmatrix.com;sales@szmatrix.com ChapterⅡ Technical Specifications 2.1 Main technical specifications Four-channel programmable DC power supply technical specification table: Model IV-6054 IV-3104 Rated input voltage AC220V±5% aisle Rated output voltage 0-60V 0-30V Rated output current 0-5A 0-10A Transformer way Linear power... -
Page 8: Supplementary Features
MATRIX TECHNOLOGY INC. www.szmatrix.com;sales@szmatrix.com 2.2 Supplementary Features State memory capacity: 9 groups of operating states Recommended calibration frequency: 1 year/1 time Cooling method: forced air cooling Operating ambient temperature: 0 to 40 ℃ Storage ambient temperature: -20 to 70 ℃ Use environment: indoor use design, pollution level 2, maximum humidity 80% Chapter Ⅲ... - Page 9 MATRIX TECHNOLOGY INC. www.szmatrix.com;sales@szmatrix.com The rear panel layout of the four-way programmable DC power supply is shown in the following figure. Picture 3.2 Four-channel programmable DC power supply rear panel ① Rear output terminal and SENSE (remote range port) "L" is the rear output terminal, "S"...
-
Page 10: Pre-Check
After power on, the power supply system first check and test itself, and then enters the standby state. 3.3 If the power does not start Use the following methods to solve the problems you may encounter when turning on the power. 1. Check whether the power cord is connected properly Fuse specifications Model 230V IV-6054 IV-3104... -
Page 11: Chapter Ⅳ Panel Operation
MATRIX TECHNOLOGY INC. www.szmatrix.com;sales@szmatrix.com 2. How to replace the fuse Use a screwdriver to open the small plastic cover below the power input socket on the rear panel of the power supply, and you can see the fuse. Please use a fuse that matches the specification. -
Page 12: Front Panel Basic Operation
MATRIX TECHNOLOGY INC. www.szmatrix.com;sales@szmatrix.com Key Description Button position Button function description 0-9 : Number key Esc : Number key input and exit I-Set Set the maximum output current V-Set Set power supply output voltage Save Power storage current correlation parameter to a specified storage location set Recall Recall power-related setting parameters from the designated storage... -
Page 13: Voltage Setting
MATRIX TECHNOLOGY INC. www.szmatrix.com;sales@szmatrix.com 4.3 Voltage setting The voltage setting range is between 0V and the maximum voltage setting value. You can use the following two methods to set the output voltage value through the front panel. The set voltage is the value of the channel indicated by the current cursor. -
Page 14: Memory Recall Function
MATRIX TECHNOLOGY INC. www.szmatrix.com;sales@szmatrix.com 4.5 Access operation The power supply can save some commonly used parameters in 9 groups of non-volatile memory for users to quickly recall. You can use the Save and Recall keys on the front panel to access (0~9) groups of memory areas. -
Page 15: Menu Setting
MATRIX TECHNOLOGY INC. www.szmatrix.com;sales@szmatrix.com Note: After setting, press "ESC" to exit or wait about 10 seconds to exit automatically. 4.7 Menu setting Press shift and then press the number key "0" to enter the menu setting function, press the ▲ and ▼ keys to switch options, the screen will display as follows: 1．P-UP ON/OFF ( Enable switch in power-on state, ON is turned on, OFF is turned off, set by the knob, and confirm by the "... - Page 16 MATRIX TECHNOLOGY INC. www.szmatrix.com;sales@szmatrix.com 3. Key Beep Set ON/OFF (beeper enable switch, ON is turned on, OFF is turned off, the default value is "ON", use the knob to change the setting, press the "Enter" key to save, when the button is set to ON, there is a sound, No sound when set to OFF button,) 4.
-
Page 17: Chapter Vremote Operation Mode
MATRIX TECHNOLOGY INC. www.szmatrix.com;sales@szmatrix.com 8. Reset Power NO (factory initialization setting, turn the knob left and right to change the selection, press the "Enter" key to confirm, NO means no initialization, YES means initialization, all parameters will be set to factory defaults after initialization.) Chapter V Remote operation mode 5.1 Communication between power supply and PC... -
Page 18: Chapter Vi Scpi Communication Protocol
MATRIX TECHNOLOGY INC. www.szmatrix.com;sales@szmatrix.com 3.Interface pin definition RXD（accept data） TXD（send data） GND（ground） Chapter VI SCPI communication protocol Command format According to the SCPI command syntax, the short mnemonic uppercase format is supported. 1. The braces ({}) contain the parameter options of the given command string. The braces are not sent with the command string. - Page 19 MATRIX TECHNOLOGY INC. www.szmatrix.com;sales@szmatrix.com power supply through a PC. Communication set Before operation, you should first match the power supply with the following parameters of the PC. Baud rate：4800/9600/19200/ Data bits：8 Stop bits：1 Calibration: None IEEE 488.2 common demand *IDN? This query command reads the identification string of the power supply.
- Page 20 MATRIX TECHNOLOGY INC. www.szmatrix.com;sales@szmatrix.com For example： APP:VOLT? Return parameters: CH1 set voltage (X.XXX), CH2 set voltage (X.XXX), CH3 set voltage (X.XXX) CH4 set voltage (X.XXX), CH5 set voltage (X.XXX) ) APPly: CURRent {<CH1 Current >, <CH2 Current >,<CH2 Current >, <CH4 Current >,<CH5 Current >} This command set current value of 5 channels simultaneously.
- Page 21 MATRIX TECHNOLOGY INC. www.szmatrix.com;sales@szmatrix.com For example: MEAS:VOLT:ALL? Return parameters: CH1 actual voltage value (X.XXX), CH2 actual voltage value (X.XXX), CH3 actual voltage value (X.XXX), CH4 actual voltage value (X.XXX), CH5 actual voltage value (X.XXX) XXX) MEASure: CURRent? This command checks the actual current output value of the channel. For example: MEAS:CURR? Return parameter: actual current value (X.XXX) MEASure: CURRent:ALL?
-
Page 22: Safety Signs
MATRIX TECHNOLOGY INC. www.szmatrix.com;sales@szmatrix.com This command is used to check the set current value of the channel. Example: CURR? Return parameter: The current setting value of the channel (X.XXX) INSTrument command INSTrument command is used to switch the channel. INSTrument {<1|2|3|4|5|>} This command is used to switch the channel. -
Page 23: Maintenance & Service
MATRIX TECHNOLOGY INC. www.szmatrix.com;sales@szmatrix.com Maintenance service If this product needs to be repaired, please return the product to the repair service center designated by our company. The customer shall bear the one-way freight for sending the repaired product to the maintenance department, and our company will be responsible for paying the return freight.
Need help?
Do you have a question about the IV-6054 and is the answer not in the manual?
Questions and answers