RiDom Ri-SCT-1 Manual

Socket «Ri-SCT-1»
Installation guide
1 GENERAL INFORMATION
1.1 The «Ri-SCT-1» socket (hereinafter referred to as the Socket) connects
external devices to the 230 V AC network and transmit notifications via a
two-way radio channel in accordance with the «Ri-Contact-R» protocol.
1.2 The socket works as part of the RiDom smart home security system,
communicating with the «Ri-HUB-1» control center (hereinafter referred to
as the Hub), which supports the «Ri-Contact-R» radio exchange protocol.
1.3 The power to the Socket is supplied from the AC mains with a rated
voltage of 230 V and a frequency of 50 Hz.
1.4 During operation, the Socket provides indication of the following
statuses:
- «Linking»;
- «Identification»;
- «Communication quality assessment»;
- "Power is supplied to the external device»;
- «Power is not supplied to the external device».
1.5 The radio exchange is initiated by the socket with a period: 10 s,
15 s, 30 s, 1 min, 2 min, 5 or 10 min, the time frame is set in the Hub.
1.6 The Socket is resistant to electromagnetic interference.
1.7 Operating modes of the socket are displayed by a two-color LED
indicator (see table 3).
2 SPECIFICATIONS
Table 1
Parameter
Frequency range
Supply voltage
Maximum power consumption
Maximum switching load current (with resistive
load, cos φ=1)
Protection class
Dimensions
Weight
Average service life
Operational conditions
Operating temperature range
Permissible air humidity at a temperature of +40 °C,
without moisture condensation
3 SCOPE OF SUPPLY
Table 2
Name
Socket
«Ri-SCT-1»
Installation guide for the «Ri-SCT-1»
4 SAFETY MEASURES
4.1 The manufacturer is not responsible for damage caused by
non-compliance with safety regulations and the rules for application
of the Socket.
4.2 The Socket is designed for domestic use and can be used in
apartments, country houses, hotel rooms, utility rooms of shops, offices
or other similar non-industrial environments. Industrial or any other
non-intended use of the Socket will be considered as a violation of the
conditions for the proper application of the product. In this case, the
manufacturer is not liable for the possible consequences.
4.3 Before connecting the Socket to the power mains, check whether
the voltage matches the rated supply voltage of the socket (see technical
specifications).
4.4 Unplug the power Socket during lightning storms, when it is not in
use for a long time or when cleaning.
4.5 Do not use the Socket outdoors: moisture or foreign objects entering
the socket body can cause serious damage.
4.6 Do not leave unattended appliances with heating elements
connected to the mains through a socket.
IT IS FORBIDDEN
4.7 The Socket is not intended for use by persons (including children)
with a physical, nervous or mental impairment or lack of experience and
knowledge, unless such persons are supervised or instructed in how to
use this appliance by a person responsible for their safety. It is necessary
to supervise children in order to prevent them from playing with the
appliance, its accessories, as well as the factory packaging. Cleaning
and maintenance of the Socket should not be carried out by children
without adult supervision.
It is forbidden to use the Socket in case of any malfunctions.
5 INSTALLATION RECOMMENDATIONS
The Socket is not recommended to be placed:
- on massive metal structures and closer than 1 m from them;
- near sources of radio interference;
- inside metal structures.
6 VIEW AND DESIGN
The Socket contains:
- LED indicator (1);
- b u t t o n ( 2 ) f o r c o n n e c t i n g
disconnecting the power, checking
the quality of communication, if the
device was linked (indicated by the
button after changing the status of the
relay), switching to the «Linking» mode.
7 INDICATION
Table 3
communication quality
«
Power is not supplied to
8 CONNECTION OF THE SOCKET TO THE SYSTEM
Value
8.1 Open the RiDom application. In the My Devices tab, click
868,7...869,2 MHz
then press
and follow the prompts of the application.
184...253 В, 50 Hz
8.2 Plug the device into a wall outlet.
1,5 W
8.3 Make sure that the green indicator on the case is turned on.
8.4 To switch the Socket to the «Linking» mode, press and hold the
7 А
button on the Socket case for 10 seconds until an intermittent green
indication appears, then release the button.
IP30
8.5 Время режима «Подключение» ограничено 100 секундами.
103х62х84 mm
The device operates only from external power in networks with a
voltage of 184-253 V 50 Hz. Do not plug in the appliances in the Soc-
0,2 kg
ket with power consumption greater than 1.5 kW.
8 years
9 COMMUNICATION QUALITY ASSESSMENT
9.1 Bring the Socket to the intended place of installation.
-30... +55 С
о
9.2 Press and hold the button for 3 seconds.
9.3 With in 5 seconds, the socket will indicate the quality of commu-
93 %
nication with the Hub by turning on the LED indicator (see Table 4).
Table 4 - Indication of the communication quality control results
Qty.
1 pc.
1 copy
10 SOCKET OPERATION FEATURES
10.1 The Socket supports the following load connection modes:
by radio channel:
- turned on;
- turned off;
- turned on with a frequency of 4 Hz;
- turned on with a frequency of 2 Hz;
- turned on with a frequency of 1 Hz;
- turned on with a frequency of 0.5 Hz.
All modes can be turned on permanently or for a period of time from
1 to 2500 seconds.
by pressing the button for 3 to 10 seconds:
- turned on;
- turned off.
10.2 The maximum switching current is calculated for a resistive load.
Reducing cos φ* reduces the maximum switching current.
* The ratio of active power to apparent
to immerse the Socket in water!
Mode of operation
« »
Linking Mode
« »
Linking is complete Turning on the red indicator for 1 second
« »
Dentification
Alternating green and red indicators
indication
«
Assessment of
»
« Power on external
»
device
»
the external device
button. Select the
Indication
Color Mode
Green Three blinks
Green Two blinks
Green One blink
Red Multiple blinks
Picture 1
Indication
Intermittent green indicator light
See table 4
Continuous red indicator light
Continuous green indicator light
Ri-SCT-1 from the list of devices
« »
Communication
quality Recommendations
assessment
Perfect
Installation in a
standard location
Good
Weak Choose a different
installation location
No connection
or use a repeater
1
2
and