RiDom Ri-KB-1 Installation Manual

Keypad «Ri-КВ-1»
Installation guide
1 GENERAL INFORMATION
1.1 The «Ri-KB-1» keypad (hereinafter referred to as the Keypad) is
designed for entering and exchanging information via a two-way radio
channel in accordance with the «Ri-Contact-R» protocol.
1.2 The keypad operates as part of the RiDom smart home security
system, communicating with the «Ri-HUB-1» control center (hereinafter
referred to as the Hub) via the «Ri-Contact-R» radio channel protocol.
1.3 The keypad does not require licensing or registration of a radio
frequency device.
1.4 Two frequencies – the main and backup – are used to exchange
radio signals between the keypad and the wireless control panel. The
transition to the backup frequency is automatic.
1.5 The keypad generates and ensures transmission of notifications via
radio channel:
- «Main battery discharge» when the battery voltage drops below
2.4 В;
-0,1
- «Backup battery discharge» when the battery voltage drops below
2.3 В.
-0,1
1.6 The keypad ensures that codes are transmitted when the
pressed. Resetting the entered codes on the keyboard is done by pressing
the key.
1.7 The keypad is designed for continuous round-the-clock operation.
1.8 The keypad is resistant to electromagnetic interference.
2 TECHNICAL SPECIFICATIONS
Table 1
Parameter
Frequency range
Radiation power
Protection class
Battery type
Duration of operation of the keypad from a battery
under normal climatic conditions and with an
average frequency of use twice a day
Dimentions
Weight
Average service life
Operational conditions
Operating temperature range
Permissible air humidity at a temperature of +25 °C,
without moisture condensation
3 CONTENTS OF THE KIT
Table 2
Name
Keypad «Ri-КВ-1»
Lithium battery СR123A
Instructions for keypad «Ri-КВ-1»
* Included
4 DESIGN
The keypad consists of the following elements (Picture 1): front panel (1)
with a printed circuit board installed in it (4), base (Picture 2). The
indicator (2) is displayed on the front panel and can be turned on or off
in accordance with the command received from the Hub.
The following components are installed on the printed circuit board: a
piezo emitter (3), «RESET» contacts (7) for switching the keyboard to the
«Linking» mode. The battery (5) with an insulator is installed in the battery
compartment (6).
5 INDICATION
The keypad generates the following types of indication (2):
- indication of the «Linking» mode (see 6.4);
- «Communication Quality» indication;
- indication «Loss of connection»;
- «Low battery» indication.
The modes of indicators depending on the status of the keypad are
presented in Table 3.
Table 3
«Linking» mode
Ending «Linking»
key is
Indication «Loss
of connection»
«Low Battery»
«Battery OK»
Value
868.7...869.2 MHz
Communication
25 mW
IP41
CR123A, 1 pc.
6 CONNECTING THE KEYPAD TO THE SYSTEM
6.1 Open the RiDom application. In the «My Devices» tab, click
12 months
and then
and follow the application prompts.
6.2 Remove the cover by unscrewing the screw at the bottom of the
146х60х25 mm
case.
0.125 kg
6.3 When prompted by the app, remove the battery isolator.
8 years
6.4 The keypad will periodically turn on the green indicator, which
indicates that it is in the «Linking» mode.
6.5 If you successfully connect to the Hub, the indicator on the keypad
-20... +55 С
о
in the application, as well as all the corresponding information about
it. Linking mode time is limited to 100 seconds. To resume the «Linking»
98 %
mode, it is necessary to briefly close the «RESET» contacts (pos. 7, Pic. 1)
with a screwdriver.
6.6 Install the cover back.
7 COMMUNICATION QUALITY ASSESSMENT
To determine whether the keypad can be used in the selected
Qty.
location, you must press the
1 pc.
display the quality of radio communication with the Hub on the indicator
1 pc.*
(pos. 2, Pic. 1) in accordance with Table 4.
1 copy
Table 4 – Indication of communication quality control results
Color
Green
Green
Green
1
2
Picture 1
Status Indication
The indicator turns green
periodically
Turns on the red indicator for 2 s
Mode
The indicator turns red 4 times
The indicator turns red 1 time
Indication when you press any key
The indicator turns green 1 time
indication when you press any key
quality See section «Communication quality assessment»
assessment
. Select the «Ri-KB-1» keypad from the list of devices
Indication
Mode
Three blinks
Two blinks
One blink
Red Multiple blinks
3
7
RESET
4
6
5
Notes
Request to
register a device
in the Hub
If there is no
connection
key, after which the keypad will
Connection
Recommendations
quality
Perfect
Installation in this
location is allowed
Good
Choose a different
Weak
installation location
No connection or use a repeater