1. Manuals
  2. Brands
  3. HALNy Manuals
  4. Enclosure
  5. HL-F-FIBER TRAY
  6. Installation manual

HALNy HL-F-FIBER TRAY Installation Manual

Hide thumbs

Advertisement

Table of Contents

Title:
HALNy HL-F-FIBER TRAY INSTALLATION
Fibrain Sp. z o.o., Zaczernie 190F, 36-062 Zaczernie 190F, Poland tel: +48 17 866 08 12; email:
INSTALLATION GUIDE
Installation guide of HL-F-Fiber Tray
GUIDE
Rev:
00
Date:
Page:
27.04.2022
1
sales@halny.com;
web: halny.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HL-F-FIBER TRAY and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for HALNy HL-F-FIBER TRAY

  • Page 1 Rev: INSTALLATION GUIDE Date: Page: 27.04.2022 Title: Installation guide of HL-F-Fiber Tray HALNy HL-F-FIBER TRAY INSTALLATION GUIDE Fibrain Sp. z o.o., Zaczernie 190F, 36-062 Zaczernie 190F, Poland tel: +48 17 866 08 12; email: sales@halny.com; web: halny.com...

  • Page 2: Table Of Contents

    HL-4GXV-F, HL-4GXVC-F, HLE-3GX-F, HLE3GXV-F installation ........8 3. Final actions: ................... 12 1. Introduction HALNy ONT Fiber Tray is innovative by its flexibility and easy installation for FTTH / FTTP installation. The solution is designed to optimize the deployment and roll-out of the service provider. Any engineer or installer can easily install the fiber tray.

  • Page 3: Installation Guideline

    Date: Page: 27.04.2022 Title: Installation guide of HL-F-Fiber Tray 2. Installation guideline: Check the conformity of the Fiber Tray before you begin the installation of the Fiber Tray. All of the components of the Fiber Tray should be clean without defects.
  • Page 4 INSTALLATION GUIDE Date: Page: 27.04.2022 Title: Installation guide of HL-F-Fiber Tray View of Fiber Tray for pre-connected patchcord placement. View of Fiber Tray drop cable entry points up to 7mm View of Fiber Tray with cable entry from all possible sides.

  • Page 5: Wall Installation

    INSTALLATION GUIDE Date: Page: 27.04.2022 Title: Installation guide of HL-F-Fiber Tray b) Wall installation To mount the Fiber Tray on the wall, 4pcs of dowels and screws are needed. 1. Remove the cover by using a flat face screwdriver as the picture.
  • Page 6 Date: Page: 27.04.2022 Title: Installation guide of HL-F-Fiber Tray 1. Locate the fixing holes on the four corners of the Fiber Tray. 2. Based on the desired position vertically or horizontally and mark out the hole position on a wall.
  • Page 7 Date: Page: 27.04.2022 Title: Installation guide of HL-F-Fiber Tray 4. Place the top cover back based on the installed position, by clicking back to the latch as in the picture. Fibrain Sp. z o.o., Zaczernie 190F, 36-062 Zaczernie 190F, Poland tel: +48 17 866 08 12; email: sales@halny.com;...

  • Page 8: C) Hl-4Gxv-F, Hl-4Gxvc-F, Hle-3Gx-F, Hle3Gxv-F Installation

    INSTALLATION GUIDE Date: Page: 27.04.2022 Title: Installation guide of HL-F-Fiber Tray c) HL-4GXV-F, HL-4GXVC-F, HLE-3GX-F, HLE3GXV-F installation 1. Remove the cover by using a flat-face screwdriver as in the picture. Or by following method 2 2. Remove the cover by pulling from the centre, then use the thumb to remove the lid out from the latch as in the picture.
  • Page 9 Rev: INSTALLATION GUIDE Date: Page: 27.04.2022 Title: Installation guide of HL-F-Fiber Tray Fibrain Sp. z o.o., Zaczernie 190F, 36-062 Zaczernie 190F, Poland tel: +48 17 866 08 12; email: sales@halny.com; web: halny.com...
  • Page 10 Rev: INSTALLATION GUIDE Date: Page: 27.04.2022 Title: Installation guide of HL-F-Fiber Tray Vertical installation HL-4GXV-F,HL4GXVC-F,HLE-3GX-F,HLE-3GXV-F 1. Remove the dust cap from the HL-4GXV-F or HL- 4GXVC-F or any other Fibrain housing ONT with SC/APC port. 2. Remove the pre-connected SC/APC patchcord from the placement holder and connect it to the ONT.
  • Page 11 Rev: INSTALLATION GUIDE Date: Page: 27.04.2022 Title: Installation guide of HL-F-Fiber Tray Horizontal installation HL-4GXV-F,HL4GXVC-F,HLE-3GX-F,HLE-3GXV-F 1. Remove the dust cap from the HL-4GXV-F or HL- 4GXVC-F or any other Fibrain housing ONT with SC/APC port. 2. Remove the pre-connected SC/APC patchcord from the placement holder and connect it to the ONT.

  • Page 12: Final Actions

    Rev: INSTALLATION GUIDE Date: Page: 27.04.2022 Title: Installation guide of HL-F-Fiber Tray 3. Final actions: VERFIY INSTALLATION BY CHECKING ALL SIDE ARE INTACK WITH THE FIBER TRAY ➔ Vertical installation ➔ Applies to all models Fibrain Sp. z o.o., Zaczernie 190F, 36-062 Zaczernie 190F, Poland tel: +48 17 866 08 12; email: sales@halny.com;...
  • Page 13 INSTALLATION GUIDE Date: Page: 27.04.2022 Title: Installation guide of HL-F-Fiber Tray VERFIY INSTALLATION BY CHECKING ALL SIDE ARE INTACK WITH THE FIBER TRAY ➔ Horizontal installation ➔ Applies to all models Fibrain Sp. z o.o., Zaczernie 190F, 36-062 Zaczernie 190F, Poland tel: +48 17 866 08 12; email: sales@halny.com;...

This manual is also suitable for:

Hl-fiber-tray

Table of Contents