Subscribe to Our Youtube Channel
Summary of Contents for Berkeley 5PNP15H
- Page 1 OWNER’S MANUAL Shallow Well Water System 3869 0101 Installation/Operation/Parts For further operating, installation, or maintenance assistance: Call 1-888-782-7483 © 2014 BE586 (02/28/14)
- Page 2 Safety INTRODUCTION Please read our instructions before installing and using your Shallow Well Water System. This will help you obtain the full benefits of the quality and convenience built into this equipment. It will also help you avoid any needless service expense resulting from causes beyond our control which are not covered by our warranty.
-
Page 3: Limited Warranty
ATTACH ORIGINAL RECEIPT HERE FOR WARRANTY CONSIDERATION. Limited Warranty BERKELEY warrants to the original consumer purchaser (“Purchaser” or “You”) of the products listed below, that they will be free from defects in material and workmanship for the Warranty Period shown below. - Page 5 Safety For a pump at sea level mounted directly over the well, be sure the total lift from the pumping water level to the pump does not exceed 25 feet. This will be less if the pump is offset from the well. The maximum lift of any pump decreases at the rate of about 1’...
- Page 6 Convert to 115 Volts as shown. Do not change motor Disconnect power before working on pump, motor, wiring if line voltage is 230 Volts or if you have a single pressure switch, or wiring. voltage motor. ConTank nearly empty 68air expands filling area abov Your Motor Terminal Board (under the motor end cover) and Pressure Switch look like one of those shown below.
- Page 7 Safety Hazardous voltage. Can shock, burn, or kill. Connect ground wire before connecting power sup- ply wires. Use the wire size (including the ground wire) specified in the wiring chart. If possible, connect the pump to a separate branch circuit with no other appli ances on it.
- Page 8 Safety Lubrication It is not necessary to lubricate the pump or its motor. The motor bearings are lubricated for life. The mechanical shaft seal in the pump is water lubricated and selfadjusting. Draining for Winter Risk of electric shock. Disconnect power before working on unit.
-
Page 9: Maintenance
Maintenance 6. Pull valve through hole with pliers or a valve tool (available at your local filling station or Automotive Center). 7. Follow steps 14 through 20 under “Vinyl Bag Re placement”, Page 8, to reinstall bag in tank. Testing for Bag Leakage 1. - Page 10 Maintenance 4. Place seal plate face down on flat surface and tap out ceramic seat. NOTICE: Do not force out copper insert. If it has moved, leakage will occur. See section on installing copper insert on Page 11. 5. Clean seal cavity. 6.
- Page 11 Maintenance c. Both mounting screws must engage screw 1. Remove copper insert as shown in Figure 12. do not holes in seal plate. See Figure 10. deform. d. Be sure rubber pad (Figure 10; Key No. 8, Page 13) stays in place on top of diffuser. 2.
-
Page 12: Helpful Hints
Maintenance HELPFUL HINTS Cleaning Impeller 1. Follow steps 1A through 1D under “Disassembly How to Handle a Gaseous Well and Assembly of Pump” on Page 9. In some areas well water contains gases which must be 2. Remove diffuser and impeller from pump per allowed to escape before the water is used. - Page 13 Repair Parts Repair Parts...
-
Page 14: Repair Parts
Repair Parts Repair Parts - Tank Only... -
Page 15: Troubleshooting
Troubleshooting Troubleshooting TROUBLE POSSIBLE CAUSES REMEDIES Motor will not run 1. Disconnect switch is off 1. Be sure switch is on 2. Fuse is blown 2. Replace fuse 3. Starting switch is defective 3. Replace starting switch 4. Wires at motor are loose, 4.
Need help?
Do you have a question about the 5PNP15H and is the answer not in the manual?
Questions and answers