tacwise A11 Eco - Hammer Tacker Manual
  1. Manuals
  2. Brands
  3. tacwise Manuals
  4. Tools
  5. A11 Eco
  6. User manual

tacwise A11 Eco - Hammer Tacker Manual

Also See for A11 Eco:

Advertisement

Table of Contents
Contents
tacwise A11 Eco - Hammer Tacker Manual

Features


Please make sure that the person using this tacker carefully reads and understands these instructions before use.

Features

  1. Pin
  2. Magazine pusher
  3. Magazine channel
  4. Personalisation window
  5. Magazine
  6. Staple mouth

Loading the tool with staples

NOTE: Do not load fasteners of different lengths together.
NOTE: Ensure the magazine is facing away from you and others.

  1. Push the magazine pusher end in and up, then pull the magazine pusher out fully.
  2. Insert the staple strip along the magazine channel inside the handle, sitting the staples on top of the rail with legs facing down.
  3. Push the magazine pusher back in and down over the metal latch in the handle. Ensure the pusher is fi rmly latched back into position securely.

NOTE: We strongly recommend that you only use approved/genuine Tacwise staples, for reliable stapling.

Operating the tool

  1. Hold the hammer in your hand with a fi rm grip, as you would a conventional hammer.
  2. Select the area to be stapled and bring the hammer down in a striking motion.
  3. Repeat the procedure for additional stapling.

Unloading the tool

  1. Remove the magazine pusher (see previous section).
  2. Tilt the tool with the handle end down to remove any unused staples in the channel.
  3. Re-insert the magazine pusher (see previous section).

Personalisation window

  1. Remove the plastic cover.
  2. Write your initials or name on the card insert before replacing the plastic cover.

Removing jammed staples

NOTE: You must remove any jammed staples before using the tool any further as you could cause damage to the mechanism.
NOTE: Ensure the magazine is facing away from you and others.

  1. Press the magazine pusher end in and up, then remove the magazine pusher.

  1. Tilt the tool to remove any unused staples in the channel (you can use pliers for ease), this should clear the jammed staple(s). If not, then remove the magazine as per the instructions below.

  1. Do not insert the damaged staple(s) back into the magazine.
  2. Always carefully test the tool function before fully proceeding with any work.

Removing the magazine

NOTE: Ensure the staple mouth is facing away from you to reduce the risk of personal injury.

  1. Remove the magazine pusher and remove any loose fastenings.
  2. Using a suitable narrow object, push the pin through from the reverse side of the handle.
  3. Pull the pin out.
    TIP: To make it easier to remove the pin,     gently squeeze the magazine into the metal housing to release the pressure on the pin.
  4. Remove the metal magazine from the top end of the tool.

Reassembling the magazine

  1. Reposition the metal magazine back into its original place, inserting it from the staple mouth and aligning the holes in the handle.
  2. Insert the pin through the hole until it is fi rmly back in place. Ensure the pin is fully inserted.
    TIP: To make it easier to insert the pin, gently squeeze the magazine into the metal housing to fully align the holes.
  3. Re-insert the magazine pusher.

Troubleshooting

Follow the instructions below if your tool seems not to operate properly. If this does not solve the issue, please contact: service@tacwise.com

Staples jammed in tool

Tool does not fire staples

Tool does not drive the staples fully
  • Use genuine Tacwise staples as specified for the tool.
  • Ensure the staple type and length is suitable for the material.
  • Clear/clean the magazine and staple mouth.
  • Load staples into the magazine.
  • Use genuine Tacwise staples as specified for the tool.
  • Clear/clean the magazine and staple mouth.
  • Check the magazine pusher is firmly secured into the end of the tool.
  • Choose the appropriate staple length for the material.
  • It may be necessary to use more force when firing the tool.


  • The operator and persons in the vicinity of the tool should wear CE or UKCA approved eye protection/goggles.
  • Do not go through the motion of firing unless the tool is aligned to the workpiece, as this could pose a risk of injury to others.
  • Only use Tacwise staples as others may cause jamming or damage to the tool.
  • Store out of reach of children and pets.
  • Keep your work area clean and well lit.
  • Always watch what you are doing and use common sense.
  • Do not wear loose clothing or jewellery that can get caught on the tacker.
  • Do not swing the hammer tacker in the direction of others
  • Be aware of the materials that you are stapling – watch out for potential hazards
  • Do not overreach; keep proper footing and balance at all times
  • Do not use this tool to fasten electric cables. This tool is not designed for the installation of electric cabling and may damage electric cables, which could lead to injury by electric shock or fire hazards.

Product advice & technical support

If you have a problem with your Tacwise hammer tacker, email: service@tacwise.com

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download tacwise A11 Eco - Hammer Tacker Manual

Advertisement

Need help?

Need help?

Do you have a question about the A11 Eco and is the answer not in the manual?

Questions and answers

Related Manuals for tacwise A11 Eco

Save Article as PDF

Table of Contents