Advertisement
Quick Links
Precision Router Table Top
OWNER'S MANUAL
GUIDE D'UTILISATION • MANUAL DEL PROPIETARIO
Item# PRS1025
Article #PRS1025
Artículo # PRS1025
Tools Required:
• Phillips-head screwdriver
• Straight-slot screwdriver
• ⅛" hex wrench (included)
• #2 square driver (included)
• Double-faced tape
• Electric drill or drill press
• Drill bits
• Countersink bit
NK8854
Version 6 - 05/2018
Outils nécessaires :
• Tournevis cruciforme
• Tournevis à tête plate
• Clé hexagonale de
⁄
po (incluse)
1
8
• Tournevis carré n
2 (inclus)
o
• Ruban adhésif à double face
• Perceuse électrique ou à colonne
• Forets
• Fraise
( 24" x 32" )
Herramientas necesarias:
• Destornillador Phillips
• Destornilladores de punta recta
• Llave hexagonal de
1
• Punta de destornillador cuadrada
#2 (incluida)
• Cinta doble faz
• Taladro eléctrico o prensa de taladrar
• Brocas para taladro
• Broca para avellanar
⁄
pulg (incluida)
8
Advertisement
Related Manuals for Kreg PRS1025
Summary of Contents for Kreg PRS1025
- Page 1 Precision Router Table Top ( 24" x 32" ) OWNER’S MANUAL GUIDE D’UTILISATION • MANUAL DEL PROPIETARIO Item# PRS1025 Article #PRS1025 Artículo # PRS1025 Tools Required: Outils nécessaires : Herramientas necesarias: • Phillips-head screwdriver • Tournevis cruciforme • Destornillador Phillips •...
-
Page 2: General Safety Instructions
General Safety Instructions WARNING When using electric tools, always follow the safety precautions below to reduce risk of fire, electric shock, and personal injury. Read all these instructions before attempting to operate this product. SAVE THESE INSTRUCTIONS. 1) Work area safety a) Keep guards in place and in working order. - Page 3 This router table is designed for a specific application. Do not modify and or use it for any other application. If you have questions relative to the application of the router table, DO NOT use it until you have contacted Kreg Tool Company and have been advised accordingly.
-
Page 4: Exploded View
Exploded View Parts Item# Description Kreg Part# Quantity Item# Description Kreg Part# Quantity Table top NK8324 ¼-20 x 1½″ set screws RT10111 Combo-Trak NK8151 Insert plate NK8840 5mm system screws 20mm long NK8025 ¼-20 x 1¾″ flathead machine screws RT10112... - Page 5 Assembly Assemble the top The table top (1) is shipped with the combination miter-gauge track/ T-track (2) in place, but fastened only with a plastic rivet. Remove the rivet and secure the track with the system screws (3), driving them into the holes in the table top.
- Page 6 ATTENTION To view a free video that shows you how to drill your insert plate, go to www.kregtool.com. You also can have Kreg do the drilling for a fee. For complete information, go to www.kregtool.com/plateprogram. ATTENTION The included insert plate has center points molded into the bottom face for drilling mounting holes for the following routers: Pattern 1 (three holes): Bosch 1617 and 1618;...
- Page 7 When ready for use, thread the starting pin assembly into the threaded hole in the insert plate. ATTENTION When using the Kreg Precision Router Table Fence PRS1015 on your router table, store the starting pin in the threaded hole at the rear of the clamp block.
- Page 8 If you have questions relative to the especially important to use straight, flat stock and avoid warped, bowed, or twisted application of the router table, DO NOT use it until you have contacted Kreg Tool stock.
Need help?
Do you have a question about the PRS1025 and is the answer not in the manual?
Questions and answers