Related Manuals for PRETUL PULA-7P
Summary of Contents for PRETUL PULA-7P
- Page 1 Manual Variable speed polisher 175 mm 1200 W 7 ” Power Diameter Applies for: Code Model 28151 PULA-7P PULA-7P Read this manual thoroughly CAUTION before using the tool.
-
Page 2: Table Of Contents
Contents CAUTION Technical data Power requirements To gain the best performance of the tool, prolong the duty life, General power tool make the Warranty valid if safety warnings necessary, and to avoid hazards of fatal injuries please read and Safety warnings for the use understand this Manual before of variable speed polishers using the tool. -
Page 3: Technical Data
Technical data PULA-7P Code 28151 Description Variable speed polisher Diameter 7” Voltage 127 V Frequency 60 Hz Current 9.5 A Power 1 200 W No load speed 1000 RPM – 3 500 RPM 20 minutes of work per 10 minutes of rest. -
Page 4: General Power Tool Safety Warnings
General power tool safety warnings WARNING! Read carefully all safety warnings and instruction listed below. Failure to comply with any of these warnings may result in electric shock, fire and / or severe damage. Save all warnings and instructions for future references. - Page 5 Safety warnings for the use of variable speed polishers This electric tool is designed to work as a polisher. Read all safety warnings, instructions, illustrations, and specifications provided with this electric tool. • Failure to follow the instructions below can result in •...
- Page 6 Safety warnings for the use of variable speed polishers Kickback and related warnings • Kickback is a sudden reaction when a rotating wheel, backing pad, brush, or any other accessory becomes jammed or snagged. Jamming or snagging causes a rapid stoppage of the rotating accessory, which in turn forces the power tool uncontrollably in the opposite direction of the accessory's rotation at the point of operation.
-
Page 7: Parts
Parts Spindle lock Speed control Main handle Power cable Polishing buff Trigger Lock-on button switch Carbon brush cover Hook & loop attachment disc Auxiliary handle Polishing Hex key pads D-handle Carrying bag Sanding disc ENGLISH... -
Page 8: Preparation
Preparation Assembly of the D-handle • Align the D-handle with the head of the polisher and match the screw holes (A). • Securely screw the D-handle to the polisher head using the included screws, washers, and key. Assembly of the auxiliary handle •... -
Page 9: Start Up
Preparation Polishing application • Most polishes come in paste or liquid form. Before using any polish, read all instructions regarding the product's uses and the correct application method. • Application of liquid polish. • Application of paste polish. Apply a small circle of liquid, approximately 3 cm in Using a putty knife or any other flat, dull object, apply diameter, in the center of the buffing wheel, followed by about a teaspoon of paste to the buffing wheel. - Page 10 Start up Speed control • The tool can be operated at different speeds. These are selected by adjusting the speed control from minimum to maximum (C). Turn the speed control while referencing the speed chart (D). • Generally, low speeds are recommended for small work areas, and high speeds for larger surfaces.
-
Page 11: Maintenance
Maintenance Carbon brush replacement • Always ensure that the tool is disconnected from the power when performing machine maintenance. • It is necessary to replace worn-out brushes (burnt, • Remove chips, oil, and grease from the machine. Keep broken, or less than 5 mm long) with new brushes. the tool and interchangeable accessories clean. -
Page 12: Notes
Notes ENGLISH... - Page 13 Notes ENGLISH...
- Page 14 Notes ENGLISH...
-
Page 15: Authorized Service Centers
Authorized service centers In the event of any problem contacting a TRUPER Authorized Service Center, please see our webpage WWW.TRUPER.COM to get an updated list, or call our toll-free numbers 800 690-6990 or 800 018-7873 to get information about the nearest Service Center. AGUASCALIENTES DE TODO PARA LA CONSTRUCCIÓN MORELOS... -
Page 16: Warranty Policy
Code Model Brand 28151 PULA-7P Warranty. Duration: 1 year. Coverage: parts, components and workmanship against manufacturing or operating defects, except if used under conditions other than normal; when it was not operated in accordance with the ® . To make the warranty valid, instructive;...
Need help?
Do you have a question about the PULA-7P and is the answer not in the manual?
Questions and answers